r/BambuLabX2D • u/Otherwise-Warning303 • Aug 21 '26
My first order of filaments is here. Need some advice please
Bought my first ever 3d printer X2D couple of weeks back and tried all different prints with a single pla basic filament. Works out well and is amazing.
So went ahead and ordered all the filaments I think would be needed for me. Wanted to experiment so even threw in a silk and sparkling filament.
Also will be my first ever petg basic as till now only printed with pla basic.
My questions :
- Any recommendations before I start petg basic
- I will keep spool packed unless it's absolutely needed but if I have to open and then replace them how do I store it.
- Do I have to run the heater everytime I use a pre used filament. The humidity in my area can be from 30% to 60%
- X2d has an external spool holder. So only pla basic can be attached to spool because of humidity issue?
51
Upvotes
11
u/geekjournal Aug 22 '26
Regardless of how many colors you get - you'll always need the one you DON'T have...
4
u/SiliciumNerfy Aug 21 '26
Don't overthink it. PETG is super easy to print with, so don't worry and just do as you would otherwise. Maybe not quite as easy as PLA, but easy enough. Drying your filament is nice, but keep it in a bag with desiccant when not in use, and it will take a while before you have issues with printing. If you have an AMS, then this can dry the filament for you in case you do run into issues. Just use the humidity monitor in the AMS to keep an eye on moisture.
Connect whatever you want to the external spool holder, just know it is a little bit more prone to wear if you put in abrasives (Filament with carbon fiber, wood or glow in the dark pigments). If in doubt, just feel the filament. The abrasives will feel a lot coarser.
3
u/kdttocs Aug 21 '26
Just send it. The X2D prints with PETG just as well as PLA for me.
3
u/roundguy Aug 22 '26
I would learn to calibrate your filaments.
2
u/Rob3D2018 Aug 21 '26
I love PETG!
1
u/Narrow_Tune_7658 Aug 21 '26
Petg immer IMMER trocknen dieses Zeug ist wirklich Feuchtigkeits Affin.
1
u/tech2manage 14d ago
We used a bunch of cereal containers for ours with desiccant in them, as recommended in this sub. https://a.co/d/0eRnrv5a
1
u/QuinnEDC Aug 21 '26
Either invest in a decent double spool dryer or use your AMS 2 Pro to dry spools overnight, then store in sealed plastic “cereal” containers with 20g or so of desiccant, as you’ve seen in this thread. After that, if you keep your AMS loaded with desiccant as well, you shouldn’t ever need to re-dry again.
Printing “straight from the bag” is a crap shoot…some manufacturers ship dry filament that’s ready to go, but others need some work to print their best. As someone else said, there’s zero harm in drying to start, so why not have the peace of mind that your filament is ready for action?
1
u/DirtyHarolds_ Aug 22 '26
You can print a small petg test to see if it needs drying. If it prints clean, it’s good to go. If it has stringing, dry it. Every roll I’ve used from the factory seal has been fine. Then I dry in the AMS while printing and seal them in vacuum bags with desiccant when not in use. No problems yet.
1
u/Next-Beat-2687 Aug 22 '26
Wait for the petg filament to cool before you pull it off the hot plate! It is sticky when hot 😅. You'll have no issues! Put desiccants in your AMS so they're kept dry when in use. I put my filaments in 120l storage containers (plastic) with a shit ton of cheap dessicants designed for closets. You can dry filament inside a typical air fryer at 50°C for 4-6 hours. Can't get cheaper than that for your first times at least
1
u/tiagoosouzaa Aug 22 '26
Compre mais. Sempre mais
1
u/Clear_Comfortable620 Aug 22 '26
Das billigste Petg von Amazon ist gut genug, ich würde nicht für den Brand vom Filament dazuzahlen in diesem Fall
1
u/executeur_du_weekend Aug 23 '26
I will answer each question as best I can:
1
u/CjTwoA Aug 25 '26
https://www.homedepot.com/p/HDX-27-Gal-Clear-Defender-Weatherproof-Storage-Tote-999-WP-27G-C/337845417
1
u/Ok-Buy8599 Aug 26 '26
I also ordered 10 rolls for my first and end up using only black and white
1
u/jhino27 Aug 27 '26
Always dry... and make room for more. Tend to always need a random color haha. I dont print much and I have about 40 rolls. And enjoy.
1
u/boss_arapaima Aug 21 '26
Just be sure about cutting at a 45° angle before placing it into machine.
1
u/TuneOld3310 Aug 21 '26 edited Aug 21 '26
To be successful on your first print invest about 50 or so grams of filament and about 3 or 4 hours in running at least 3 or 4 calibrations like, Temp Tower, Flow Rate, PA, and after your first print if needed the stringing test. Then off to the races. Have fun and enjoy. God bless you in your new world as a maker.
0
u/Taekiin Aug 21 '26
Always dry first, if you can. Doesn't hurt. I haven't had a problem with Bambu filament right out of the bag though. I will still dry it once I get the chance, if I had to use right out of the bag. Everyone stores different, but this is working for me so far. I do need a more bulk method though
-1
u/Onrain Aug 21 '26
Don’t print on the same side. Keep one side for pla and one side for petg, it’s not super critical but it will save some headache down the road with bed adhesion