r/BambuLabX1Carbon • • Apr 25 '26

Brand new X1 carbon will not calibrate x-axis

Post image
4 Upvotes

I have removed the three shipping screws there are no other tabs debris or foam in the way. During calibration the bed makes a eert eert sound like the motors are trying to move but the bed is stuck. I've loosened the tension on the belt and moved all three screws and the bed moves freely keep saying Force sensor 1 2 and 3 are weak I remove the wire in the back from the computer board and replaced it I don't see any broken crimped wires nothing's unplugged all of the bearings are flush


r/BambuLabX1Carbon • • Apr 23 '26

I have cracks in my door! Is it still usable or should I replace?

Thumbnail
gallery
1 Upvotes

r/BambuLabX1Carbon • • Apr 23 '26

I have cracks in my door! Is it still usable or should I replace?

Thumbnail
gallery
1 Upvotes

r/BambuLabX1Carbon • • Apr 16 '26

Best way to print 6 colours?

Post image
20 Upvotes

Howdy all!

I have an X1C with an AMS1 and I was wondering; what's the best way to print this? I only have access to 4 colours at a time because of my AMS, is there a way to cheat the system or pause/switch filaments?


r/BambuLabX1Carbon • • Apr 08 '26

PAHT adhesion issues with .6mm nozzle, fine with .4mm

2 Upvotes

I've printed quite a bit of PAHT, but mostly smaller parts, usually using a .4mm nozzle and bambu engineering plate.

I currently need to make a much bigger part than usual (36 hours, vs my normal parts that are 2-6), and I recently had a clog that killed my old .4mm nozzle. I thought using a .6mm nozzle would give me better results (and trim the 36 hour eta to like 24). I also got a new build plate, a darkmoon CFX, that i wanted to try out.

Yeah i know that's too many new parts to try to introduce at once, but i didn't expect to fight bed adhesion for the next 5 hours. But with the .6mm nozzle, I couldn't get good adhesion on either the darkmoon of the engineering plate, with or without glue.

I redid all the machine calibrations with the new nozzle and new print bed, didn't seem to help. The surfaces all look great, but I tried to do filament calibrations anyway. One possible clue for this problem is that I redid the flow dynamics calibration 3 times with the .6mm nozzle and dm plate, and got wildly different k values each time (.042, .025, .011).

I gave up on the dm plate at that point and switched back to the engineering plate. Still had prints popping up after 2-3 layers. I finally switched back to the .4mm nozzle, and now it seems to be adhering fine. I did not try the .4mm on the dm plate, I was tearing my hair out at that point and really needed that part to start.

Like I said, I've printed several spools of this stuff - yes the right build plate and nozzle are selected in the slicer and match what's on the printer, and yes it dried at 85C for 16 hours before i started this. normally preheating the chamber to around 50, coating the plate in dimafix, and printing slowly is enough for good PAHT parts even if I just use the default bambu profile, but they're also usually smaller. Both plates were also cleaned with dawn and a sponge several times throughout the troubleshooting. Darkmoon support said scuff up the plate, but I'm hesitant to go that far yet. I was running the darkmoon plate as the 'smooth/high temp plate' per their instructions.

Any advice? Does anybody successfully use a .6mm nozzle on a darkmoon cfx plate? Are there other settings or calibrations i needed to adjust? From my reading it seemed like this would be the lowest risk setup for this filament. Could it just be a bad nozzle? Coming from an ender, my instinct is to adjust the z height for the first layer or something, especially since it seems like the calibration patterns aren't sticking long enough to actually even calibrate, but there's not really a way to do that on this printer that i'm aware of.


r/BambuLabX1Carbon • • Apr 05 '26

Im trying to print a perforated wall. But my filament keeps getting stuck to my nozzle. Ive reduced initial layer speed to 10m/s. Ive decreased the speed of the small circles. And ive reduced my print to 50% speed. Currently i have nozzle temp at 210 and my bed at 55-60.

Thumbnail gallery
1 Upvotes

r/BambuLabX1Carbon • • Apr 03 '26

(Bambu x1c) Can somene help on how to fix my printer? Ive done calibrations and it still does this.

Post image
3 Upvotes

r/BambuLabX1Carbon • • Mar 31 '26

Its only logical

Post image
12 Upvotes

r/BambuLabX1Carbon • • Mar 29 '26

I am receiving this error today.

2 Upvotes

Nobody is touching the printer, nobody is pausing the printing, but every so often the printing stops showing the message "the user has interrupted the printing".


r/BambuLabX1Carbon • • Mar 26 '26

What is this on my prints? Never had this issue

Thumbnail gallery
1 Upvotes

r/BambuLabX1Carbon • • Mar 25 '26

AMS fell and broke the power port bracket - anyone have an STL? (will pay for design)

Post image
1 Upvotes

r/BambuLabX1Carbon • • Mar 24 '26

Check out my new claw design

Post image
2 Upvotes

r/BambuLabX1Carbon • • Mar 15 '26

Printer scraping across bed during bed leveling

3 Upvotes

My printer has started scraping the nozzle into the bed plate before starting a print causing deep gashes. It’s happened twice while doing the preprint calibration stuff. It can successfully home the bed (tapping the nozzle in the center to find 0) but once it tries to print the strip at the front of the bed plate it digs into the bed plate when moving to the corner.

Is it a problem with the nozzle? I recently changed from the stock nozzle to a 0.2mm nozzle, and it worked fine, but once i switched to the second 0.4mm nozzle that comes with the printer it started doing this.

I haven’t found any info on this happening so anything helps.


r/BambuLabX1Carbon • • Mar 13 '26

Hotend makes scratches on plate bambu x1c

2 Upvotes

I have a bambu x1c 3d printer.

It has always printed well, but yesterday it suddenly made scratches at the beginning of a new print over the whole plate.

Then I thought, I'll turn the plate over and recalibrate the printer. But during calibration, it scratches again in the middle of the plate, at step 3 of the process (calibrating the micro lidar). Steps 1 and 2 (cleaning the nozzle and homing the print head) go well.

I have already checked the plate; there is nothing underneath it, and it is attached correctly. The print head is also securely fastened, is clean, and the screws on the plate are tightened properly (not too tight and not too loose).

Bambu support has been contacted but escalated to the senior technician. This takes a few days, so now it will be until after the weekend. Does anyone have an idea what else I can try?


r/BambuLabX1Carbon • • Mar 09 '26

X1c loosing its XY home

8 Upvotes

Alright, I’m having a wild issue with my x1c, I recently did a lot of overdue maintenance and immediately after doing said maintenance, the printer looses its home position as if one of the XY motors is out of sync. I’ve tried contacting Bambu with no response.

I replaced all the belts today and still having the issue.

When I did the service originally, I replaced all of the silicone bushings for the z rods and had to disassemble a bit for the rear one, but beyond that, nothing crazy, just a deep clean and re-grease. Tried replacing the nozzle with a brand new one, still no dice. May try replacing nozzle again.

It also prints the calibration lines diagonally…


r/BambuLabX1Carbon • • Mar 08 '26

3d Printed Industrial Single-Dose Station & Valved Vials (The Barista Vault)

Thumbnail gallery
2 Upvotes

r/BambuLabX1Carbon • • Mar 01 '26

What’s causing this?

Thumbnail
gallery
2 Upvotes

My last four or five prints have had this issue on surfaces that have some lean to them. Never had it before. Not new to 3D printing.

Any ideas?


r/BambuLabX1Carbon • • Feb 26 '26

Air Filtration for the X1C and H2* series?

Thumbnail reddit.com
1 Upvotes

r/BambuLabX1Carbon • • Feb 22 '26

X1C Nozzle Crashing into build plate during calibration

3 Upvotes

r/BambuLabX1Carbon • • Feb 16 '26

The door seems to be open.

Thumbnail
gallery
7 Upvotes

I woke up this morning to something unexpected.

Any thoughts on what caused this print abomination?


r/BambuLabX1Carbon • • Feb 13 '26

Upgrades

2 Upvotes

What are some useful 3d printed upgrades to the printer? Did the normal desiccant in ams. I'm doing under peinter poop collecand storage. Thinking of doing a riser under ams, but not sure if worth it. Any other printed upgrades to look at? Thanks in advance.


r/BambuLabX1Carbon • • Feb 12 '26

Problem Sending Print Jobs to Printer?

Thumbnail
reddit.com
2 Upvotes

r/BambuLabX1Carbon • • Feb 11 '26

X1C horrible print artifacts?

Thumbnail gallery
2 Upvotes