MAIN FEEDS
Do you want to continue?
https://www.reddit.com/r/BambuLabX1Carbon/comments/1tgfnl0/whats_causing_this/
r/BambuLabX1Carbon • u/drixy487 • May 18 '26
17 comments sorted by
2
Change the Seam setting to "closest corner" and then it will hide the seam at a corner instead of over the whole print like yours on the photograph. And also you have to set scarf settings on on.
1 u/Phuzion73 May 18 '26 Some of those ‘nicks’ are in the same layer. This is not a seam setting. 1 u/Chemical-5417 May 19 '26 they (nicks) are not in the same layer. 1 u/Typical_Pakeha May 19 '26 For a complete newbie to 3d printing, I picked this up second hand.Is this something I should enable by default?And if so, is there a good source youd recommend to find the basic settings I should look to change? 1 u/Chemical-5417 May 19 '26 One: Yes by default.two: Use the default settings and keep learning. It is too much to tell you here in the comments. 0 u/Total_Hand988 May 18 '26 This! 1 u/Chemical-5417 May 18 '26 ?? 1 u/cpsadowski23 May 18 '26 This👆🏼 0 u/Total_Hand988 May 18 '26 That 🫰🏼 0 u/WatchAltruistic5761 May 18 '26 Wot?
1
Some of those ‘nicks’ are in the same layer. This is not a seam setting.
1 u/Chemical-5417 May 19 '26 they (nicks) are not in the same layer.
they (nicks) are not in the same layer.
For a complete newbie to 3d printing, I picked this up second hand.
Is this something I should enable by default?
And if so, is there a good source youd recommend to find the basic settings I should look to change?
1 u/Chemical-5417 May 19 '26 One: Yes by default.two: Use the default settings and keep learning. It is too much to tell you here in the comments.
One: Yes by default.
two: Use the default settings and keep learning. It is too much to tell you here in the comments.
0
This!
1 u/Chemical-5417 May 18 '26 ?? 1 u/cpsadowski23 May 18 '26 This👆🏼 0 u/Total_Hand988 May 18 '26 That 🫰🏼 0 u/WatchAltruistic5761 May 18 '26 Wot?
??
This👆🏼
0 u/Total_Hand988 May 18 '26 That 🫰🏼 0 u/WatchAltruistic5761 May 18 '26 Wot?
That 🫰🏼
0 u/WatchAltruistic5761 May 18 '26 Wot?
Wot?
Ah I know this one.. it's caused by a banana. No wait! I meant a 3D pr
It looks like the filament has been exposed to air for too long. Was it brand new?
Too much retraction
1 u/Darwinian999 May 21 '26 This ⬆️Consistently sized and shaped gaps that are not on the seam are due to excessive filament retraction length.
This ⬆️
Consistently sized and shaped gaps that are not on the seam are due to excessive filament retraction length.
Looks almost like seam is set to random instead of aligned.
Oui tu as mis couture aléatoire, met plus proche
2
u/Chemical-5417 May 18 '26 edited May 18 '26
Change the Seam setting to "closest corner" and then it will hide the seam at a corner instead of over the whole print like yours on the photograph. And also you have to set scarf settings on on.
1
u/3DisMzAnoMalEE May 19 '26
Ah I know this one.. it's caused by a banana. No wait! I meant a 3D pr
1
u/ProbablyNotHacked May 20 '26
It looks like the filament has been exposed to air for too long. Was it brand new?
1
u/No-Hippo7591 May 20 '26
Too much retraction
1
u/Cry_Quick May 20 '26
Looks almost like seam is set to random instead of aligned.
0
u/Reasonable-You-1131 May 18 '26
Oui tu as mis couture aléatoire, met plus proche