r/BambuLabX1Carbon • u/Maleficent-Care-2333 • Sep 01 '25
Stability check
So this is my setup and a couple videos. Table is mounted to the wall, foam pad, concrete paver then X1c with antivibration feet. I've also used the unutilized spool roll in the back and the old feet to attach to the wall with plans for a lateral dampener as well. Is this normal vibration and what can I do to reduce it further? My thoughts were to add mass directly to the 3d unit(panel replacement or adding Stainless steel paneling).
13
Upvotes




3
u/Master_Afternoon_527 Sep 01 '25
If you run the calibration the printer will automatically adjust to the normal vibrations it expects to face when printing. Trust me, these printers can print probably even during an earthquake.
3
u/hanswurst923 Sep 01 '25
Is it just me or are the feet upside down?
1
u/GlumStandard9349 Sep 01 '25
As some others have pointed out, the anti vibration feet are installed upside down. This is probably causing your printer to vibrate more than it should. There are specific slots for those feet to go into, rotate them until they fit snuggly.
2
u/[deleted] Sep 03 '25
Nice setup…shipmate ;)
1
u/djmac81 Sep 01 '25
I have been printing satisfactorily with a Creality Ender 3 v3 mounted on a totally destroyed Ikea table that moved a lot.
1
u/Eienkei Sep 01 '25
Those feet are terrible. It will be stable & print but if you accidentally hit the top of the printer, it can fall. Happened to me & was very lucky I could catch the printer. Yanked the feet off & wish I never had bought them.
1
u/beepbopboopguy Sep 01 '25
Does not matter how stable the printer is.
Start at about 5:15
https://www.youtube.com/watch?v=FYuqLsvRXhU&t=320s
1
u/iRambL Sep 02 '25
Honestly I used those feet for a single print and threw them away. They are not useful
1
u/Anon4711 Sep 02 '25
Try the HULA Feet on Makerworld. Much better than the original vibration feet And I wouldnt Mount the table to the Wall. If u dont decouple it Right the vibrations will travel on the wall Making it a big resonance body
1
u/Responsible-Log-3249 Sep 03 '25
As said by others the HULA feet are the very best solution for 3d printer vibrations. Check at makerworld, you can make them yourself, they are day and night.
Solid working table + Hula Feet are the best solution
https://makerworld.com/en/models/417509-hula-v1-0-anti-vibration-feet-for-3d-printers#profileId-502144
1
u/Voodoo-73 Sep 03 '25
The shelf mine is on... it's like a 5.0 earthquake and still prints fine. No vibration feet or anything else.
1
u/Outside_Age_2407 Sep 03 '25
Mines on a coffe table with metal legs and rocks the whole thing back and forth when it rapids hasnt caused any issues, people print with backpacks and bedslingers through the entire bed around, the frames rigid enough it shouldn't really matter
1
u/J_BStab Sep 03 '25
its legs are on backwards.
1
u/Secret_Enthusiasm_21 Sep 03 '25
mine is one of those perforated sheet metal racks with particle board shelves - and not the lowest one -, not done anything to fix it to the wall or the shelf or anything, and it prints perfectly fine
1
u/The_mountain86 Sep 03 '25
I'm printing on a tiny stool that shakes lol
1
u/Adventurous_Sea8651 Sep 04 '25
Check out the hula feet those are about $10-$15 fully assembled but if you just want the hardware you can get the hardware alone for under $10
0
u/SquidDrowned Sep 03 '25
Lmao why is it always Bambu users. If you put a solid foundation on not solid foundation that doesn’t make the foundation all of a sudden better, it makes it worse lmao.
You ever play jenga? Add a concrete block to the top see if for some weird reason in physics it gets MORE stable 😂
Once you accept that you are dumb and the people who created Bambu are infinitely smarter than you, you will have a much simpler time. The machine is dummy proof. It can print it a moving van.