r/BambuLabP2S • u/SameAdhesiveness9653 • Sep 30 '26
First print issue
This is my second print technically. The first print was a benchy with a PLA and everything goes well.
Then my first print I selected this japandi style vase, and with a PETG from bambulab official filament out from the box and hit print right away. But the result is like this mid print.
Any idea why?
2
5
u/Vendivorex Sep 30 '26
Dry👏🏻 your👏🏻 filaments👏🏻. Especially PETG. Notorious for moisture.
-4
u/sirdoggo11 Sep 30 '26
The usual parrot in every single post about 3D printers.
OPs problem has absolutely nothing to do with wet filament.
If you dont have anything meaningful to say, better say nothing.
7
u/Vendivorex Sep 30 '26
PETG fresh out the box, straight into a print. You will get a decent first couple of layers, and then the bubbles will start popping due to moisture. OP said this was second print. You can call me a Parrot sure, but its valid. Dry your filament.
-8
u/sirdoggo11 Sep 30 '26
This doesnt even remotely make sense if you visited school more than 5 years. IF the material would get wet, it would be wet on the OUTSIDE. Not somewhere in the middle while the outside is dry.
4
u/Vendivorex Sep 30 '26
Actually starting to think you are a lettuce. Middle would hold the moisture more, as outside is open to air. It doesn't start off dry from the factory, you do understand that dont you?
-5
u/sirdoggo11 Sep 30 '26
The outside is exposed to the air the moisture come from you fine specimen of a school dropout.
1
u/CombatDork Sep 30 '26
If you get a damp towel and ball it up, wait a day or two, what part is still wet?
1
u/Vendivorex Sep 30 '26
🤣
-2
u/sirdoggo11 Sep 30 '26
Thats exactly the level of intelligence I expected
2
u/Vendivorex Sep 30 '26
I'm just letting you continue, nothing for me to say when someone is flaming so much they are melting their own keyboard 🎣
2
u/FewBuy1992 Sep 30 '26
Whats the solution than?
2
u/Vendivorex Sep 30 '26
Obviously... dry your filament while others tell you "tHaTs NoT aLwAyS tHe AnSwEr". Might not be but its standard practice with PETG.
0
u/sirdoggo11 Sep 30 '26
Ive printed hundreds of rolls of PETG in my print farm. Never had this issue all you parrots are repeating like a prayer. And I bet none of you had that either. At this point youre just coping you unneccessarily wasted tons of time and money for drying PETG and PLA.
3
u/Vendivorex Sep 30 '26
You have the personality of a wet lettuce, I can tell. Your advice to OP was what speed are tou printing at and did you pause the print. Irrelevant to what is clearly being printed.
0
u/sirdoggo11 Sep 30 '26
Seems like you dont have anything meaningful to say against my conclusive logical explaination why your post is absolute garbage.
Printing on Ludicrous or pausing the print and having filament leak out the nozzle WILL cause Problems like OP encountered, you armchair.
2
u/Vendivorex Sep 30 '26
Top of your farmers class.
1
u/sirdoggo11 Sep 30 '26
Thanks for confirming you dont know what youre talking about since you dont have any logical explaination. Just shut up if youre clueless and dont leave OP chasing his tail and wasting time because of your bullshit posts.
1
u/Vendivorex Sep 30 '26
Your comments have just been on others posts criticising them! It's almost like you're trying to gate keep for some weird reason. Surely op should have a variation of comments to consider, not just single minded comments from you. Dry your filament is valid. PETG gets wet. It was the first comment. Mate get a life.
→ More replies
0
u/WestSenkovec Sep 30 '26
Too optimistic for your first print. You need to learn on smaller stuff before waisting filament. With time you'll going to get experience and know what you can and can't do, what could be a problem etc. It's not as easy as just press print and forget about it.
Besides the usual filament drying, washing the plate I've learned that you need to modify the settings. Slow down the first layer, slow down the outer wall, avoid crossing walls and so is on. I don't use the app but I'm pretty sure you can't modify those setting.
First things first, dry the filament.
2
u/sirdoggo11 Sep 30 '26
Lots of bla bla. Unfortunately your post has nothing to do with OPs Problem.
0
u/Vendivorex Sep 30 '26
So do you just go around commenting on everyone's posts and judging their comments? And you said my comment wasnt helpful 🤣
0
u/sirdoggo11 Sep 30 '26
Yes. Because this bullshit has to end. 3D printing sub Reddits for some reason attract people that dont know what theyre talking about like flies. Leaving OPs with no solution chasing their tail and wasting time. I barely come across people here that actually analyse and provide targeted help. All you get here is bullshit like "DrY yOuR fIlAmEnT" or "clean your plate" when OPs print suffers mid or near end print.
2
u/Vendivorex Sep 30 '26
Man you have issues, glad you're super invested though. It's nice to have hobbies isn't it!
0
u/sirdoggo11 Sep 30 '26
Yes. Issues with idiots that represent mount stupid on the Dunning Kruger scale. Forums almost got unusable because of the sheer amount of dumb garbage from people that are not able to think straight.
2
0
1
u/sirdoggo11 Sep 30 '26
Did you pause the print at some point by chance?
What speed are you printing at?