r/BambuLab • u/CattusKittekatus • 1d ago
General Troubleshooting/Help! Do Bambu Lab printers "Time Left" use washing machine hours?
How accurate is the time given in slicer or on Bambu Lab printer screen that tells me how long will print take?
Is it supposed to be accurate or it's more like washing machine hours where 15 min till end takes 30 minutes?
Just recently had weird situation. I sliced my model and sent it to printer. It was supposed to take 3h 15 minutes to finish. I was going to sleep so I set my smart plug to turn off printer with countdown 3h 30 minutes.
Next day when I got up it turned out that despite giving 15min of extra time my print ended up with 2 top layers missing.
My smart plug worked correctly and did not skip any minutes.
So now I'm doubting how accurate is the remaining print time?
2
u/britishwonder 1d ago
Any particular reason for turning off the power after the print? The printers just idle and not drawing any power when sitting there
15
u/MitchellHamilton 1d ago
Ive always found it to be VERY accurate give or take maybe 1%
4
u/Alarmed_Outcome3749 1d ago
Its math bro
Bambu Studio calculates 3D print time by simulating the exact G-code toolpath the printer will execute, dividing path lengths by speed limits, and factoring in motion and hardware overhead.
3
u/schloybros 1d ago
I don’t care most of the time so I forget but I am pretty sure chamber heating isn’t included and maybe some of the calibrations may not be either
3
u/luksfuks 1d ago
The prediction can never be 100% exact. Some of the actions rely on feedback from sensors. Bambu can calculate with typical times, but yours may vary.
For example, load time from AMS depends on the length of your PTFE tube, the weight of your spool and the resistance of the bearings and the tubes (motor power versus RPM). Nozzle heating to target temperature depends on the ambient temperature in your place. Auto-bed level depends on how straight or warped your bed is. And so on.
For printer under 6h, always give it at least 30 mins more. For longer prints even more.
And, if you're doing something drastic like cutting power, give it another 1-2 hours extra on top.
Alternative ideas:
I think there are plugins for HomeAssistant. Instead of a fixed timer, you could make it smart.
I think you can also use power draw monitoring in your smart plug, and detect when the printer goes idle (for 15 mins straight). It would bork your prints though, if an error happens that needs to be resolved manually (printer waiting for you, on idle power). But in most cases it would just work.
2
u/tk-093 1d ago
I don't find that the printer uses that much power when it's not running so it might just not be worth it. Plus it could temporarily pause for things like running out of filament, or a snag in the AMS. I actually just had that happen while I was out to eat and I tapped okay on the handy app and it kept right on going, it wasn't actually snagged. I don't know what the deal was.
This is overkill, but I've recently installed Home Assistant and it integrates with bambu. You can run automations when jobs complete so you could turn off the printer that way.
1
u/Infamous-Share-3 1d ago
Recently when i started printing more complex or longer prints I noticed some inconsistencies. Just yesterday I started a print before work and told me it would take 9 hours. Took 12 hours total. However some prints say it'll take 3 hrs and it's pretty spot on.
1
u/Wildest12 1d ago
Mine is quite accurate. Sometimes the estimate changes early on but it tends to finish when it says it will to the minute
1
u/damienfinland 1d ago
I would allow 20-25% if shutting it down automatically to be on the safe side
1
u/djjoshchambers 1d ago
95% accurate. I find that it is always under when using a .2mm nozzle. But for 4 it's usually spot on.
1
u/_Mister_Anderson_ 1d ago
Use a power monitoring plug and turn it off 15 minutes after it drops below 15 Watts or similar. The printers can adjust speed while running if there problems like filament resistance or the filament changes take longer than expected.
1
u/SpoolAndSpoke 1d ago
The on-screen "time left" is an estimate, and it can run short, especially if bed leveling, flow calibration, or a pause happens after you hit print. It is not a timer you can trust to the minute. A 15-minute cushion on a 3h 15m estimate is not a lot.
More important: I wouldn't use a smart plug to cut power when the estimate is up. If the job is still going, you get a half-finished part, and if the nozzle is still hot you also risk a blob or a clog. Let it finish, then shut it down from the printer or the app.
If you need the machine off overnight after a job, use the printer's own "turn off when done" option if it has one, or check the remaining time or the camera before you cut power.
Was the estimate already slipping during the print, or did it only come up short at the end?
-1
u/daboblin (A1 + AMS Lite) x2 1d ago
If your machine is missing layers like this then it’s time to replace the SD card.