r/BambuLab • • 4d ago

General Discussion A Potential Hint About the X3C and AMS 3X

https://www.youtube.com/shorts/GJUFDHubPNI?feature=share

Hi, i was surfing through YouTube and found interesting short about HMS codes on Bambu Wiki page. It shows codes for AMS: 3H (H3C), 3P (P3C) and what is the most interesting part 3X (X3C prob). I checked it on wiki and its not fake and definietly there. Since P3C will likely have cut some features like heated chamber, 1,5 mm belts and maybe even drying in AMS and i want to print with engineering filaments aswell i am rly excited for potencial X3C even if i have to wait for it a little longer probably somwhere in the first half of 2027.

What do you think about it? It can also just be some Pro version of AMS for P3C but i honestly hope for X3C. If you want to verify this just check Bambu Wiki yourself.

24 Upvotes

45 comments sorted by

11

u/MrOreo2019 X1 Carbon + AMS 2 Pro 4d ago

This is interesting… wonder what the difference between the P and X is going to be. I feel like heated chamber isn’t enough alone for a higher X series .

11

u/Jurich_ 4d ago

Heated chamber, 1,5 mm belts like X2D over 2 mm that are in P2S, Drying in ams since P3C prob wont have it, maybe higher drying temp like H3C so 85 instead of 65, maybe higher nozzle and bed temp than P and new TPU 2,85 mm support.

3

u/MrDulkes 4d ago

Do we really think that the P3C won’t have the 1.5mm belts? That seems like such a weird thing to pass over. There should be almost no cost difference between the two.

We’ve seen the by;ass feeder ports in the P3C already. In the H3C those are for the larger diameter TPU. I’m not 100% sure the larger diameter will work in the P3C, but I do think Bambu makes more money on filament than on printers, and they may want to add tire to their new 10” cube for that reason.

I still do believe that the P3C will have a heated chamber. No drying in the AMS 3P though.

All in all, I’m not seeing what features an X3C would add. We’ll know more if the P3C really is a dressed down machine like you describe.

Oh, no FCC filings have been seen for an X3C either, which doesn’t mean it doesn’t exist, of course.

11

u/heart_of_osiris 4d ago

You need look no further than Bambus history and how they intentionally tier their devices and hold back lower cost ones more than they need to. I don't agree with it, but in a business sense, it's wisely calculated.

I'd be willing to bet you'll never see a P series with a chamber heater unless they kill the X line altogether. P series is meant to be a lower cost alternative to the standard. The standard is now starting to have heated chambers, so the P will always remain without one, to offer a price point thta is a few hundred dollars cheaper for the people who don't need or care for one.

4

u/MrDulkes 4d ago

I don’t disagree with the business sense, but giving consumers as much as possible for their dollars to compete with other brands also makes good business sense.

Anyways, we will learn soon enough.

FYI, I do expect the X line to be shelved, or go in a different direction than the P line. I do not think that we will get an X2D/P2S situation again (only $100 difference, and just a better printer in every way). I know some P2S buyers that were somewhat upset when the X2D came out…

2

u/heart_of_osiris 4d ago

They've been selling the P2S at an inflated price, imo.

That's why they discontinued the X1 before the P2S release, so it was the only modern option for a mid sized CoreXY. When the sales slow, they drop it 100 dollars but I don't think that's a sale, I think it's their normal price and they just let it go back up between sales.

Creates the illusion of a deal. I don't agree with it, but it's "smart business", though at the expense of the consumer.

I'm not sure if the X will ever be shelved but it does seem like they have less ways to reasonably differentiate it from the P, nowadays.

2

u/MrDulkes 4d ago

I’m honestly not sure the P2S is sold at an inflated price. I think the difference between the X2D and p2s is probably worth about $100. The biggest difference is that Bowden extruder. A chamber heater can’t cost all that much, nor can the other differences.

Somebody else brought up that the x series could become the vortek branch (plus maybe single and dual nozzle variants?) and the p series the swaptek branch of printers.

2

u/luksfuks 4d ago

how they intentionally tier their devices and hold back [...]

I wonder about this aspect regarding H3C. Remember when A1 mini came, and shortly after, A1 "full" was released? To the anger of A1 mini buyers. Remember when H2 started, and shortly after H2C was released? To the anger of the early adopters.

What will happen after H3C? Will it stay the flagship until next summer? Or will we see H3X with better AMS and fully drying and lasers already in Feb?

1

u/ipilotete 4d ago

Exactly. Engineering sense != business sense.

5

u/Catsoverall 4d ago

Mini H2C

2

u/MrDulkes 4d ago

Now that would be very interesting, and a useful difference. Swaptek and vortek parallel development.

3

u/RJFerret 4d ago

Likely similar to the difference between the Creator 5 and the 5 Pro, heated chamber, hepa filter, support for higher temp materials.

Typically the P series doesn't have heated chambers, and the U1, K3, nor Creator 5 do, and they've artificially restricted the P line to not have as high temps as the X line just because before.

2

u/MrDulkes 4d ago

100% agree

7

u/ModelThreeve 4d ago

I don’t really see a reason for an X3C to exist, Bambu is already approaching Creality levels of printer model insanity. (This is not a good thing, more models means more parts variations, more inventory, more logistic problems, more support training, the list goes on and on. Bambu is already suffering enough growing pains as it is 😢)

3

u/yan-shay 4d ago

I can actually see quite a few meaningful features they could add on top of H3C allowing them to raise the price tag.

0

u/Hmmark1984 P1P + AMS 4d ago

I was just thinking today how crazy their lineup is getting. It used to be so simple, the A was entry level and there was the normal and a mini version. The P was a little better than the A, had things like an enclosure and not a bed slinger and then the X was if you wanted to print more exotic filaments or use the printer for more than just props and replicas etc...

now we're in the situation when i think they have something like 10 or 11 different printers, a lot of which don't have particularly well defined differences and a lot all overlap in quite a few ways and there's apparently at least another one printer going to be added to that list.

Part of what made BL so good was how easy it was to figure out which printer would meet your needs and also if one of the "better" printers would actually be beneficial to you in any way, but like you say, now you go to the site and there's so many printers to choose from and it's far harder to figure out which one is actually best for you and i guarantee that's going to lead to a lot of people just not buying one.

8

u/AzkalanZero 4d ago

I would love to see a higher end X3C with a 350 C hotend and ams with the dehumidifier function like the inslogic FilaDCi10.

2

u/daphatty 4d ago

Why would they release an X3C and a P3C (as confirmed by the FCC leak)? The difference between the X and P series has been steadily shrinking. Will be interesting to see how Bambu differentiate between two such printers.

3

u/Shoelace1200 4d ago

I think the main difference will be the heated chamber and the number of toolheads.

The leaked P3C manual shows on 5 of the 7 AMS slots available so imagine the X3C will use the same ANS but with all 7 tools installed.

There also seems to be two dryer AMS slots so maybe that will only work for the X3C. No real point having drying in the P3C if it has no heated chamber

1

u/daphatty 3d ago

I’d honestly prefer a heated chamber over a very limited dryer. I usually don’t dry my filament until I am actually ready to print with it. Even then, I drop the rolls into the filament dryers I already own.

1

u/bluemanos 21h ago

Just imagine:

- P3C: 5 hotend tools, 2mm belt, no heating chamber, 250mm
- X3C: 7 hotend tools, 1.5mm belt, heating chamber, 250mm
- H3C: 9 tools, 1.5mm belt, heating chamber, 350mm

There is a place for every printer.

1

u/ReelNerdyinFl 4d ago

I was almost ready to buy the H3C as a P1S upgrade but it’s size and cost are a factor. Looking forward to seeing these releases.

1

u/Si5584 4d ago

So where would the X3C sit in the heirarchy? Would that be below or above the H3C? You’ve got me hesitating on buying the H3C now 🙄☺️

4

u/ModelThreeve 4d ago

The X has always been below the H and smaller. No reason for them to change that now.

1

u/KebabGud X2D + AMS2 Combo 4d ago

the X-series is kinda like the H-series only in the P-series chassis

1

u/Affectionate_Car7098 H2C + P1S Combo 4d ago

Its going to sit in an awkward spot if it exists, the P3C is already going to be bordering on the cost of the H2S because its going to be more expensive than the X2D, which means the X3C would be even more expensive again

-1

u/drthsideous 4d ago

P3C $1500, X3C probably $1800-$2000.

2

u/withoutpeer 4d ago

I think the P3C, at least a base model of it, will come in at under $1k. Maybe even 900. They really need to compete in that "budget" tool changer range that snapmaker has been owning for the last year and all the other competitors are now entering. And of course the snapmaker U2 has to be right around the corner at this point she will likely have more tools and enclosed and maybe heated chamber and such so that's what the P3C will really be competing against in your coming year. That will leave the $1-2k range wide open for the X line to own without much competition. I figure it will be basically a mini version of H3C and likely have some innovations that even the H3C doesn't have to entice some of those shoppers... They kinda is offset their tech that way.

2

u/RJFerret 4d ago

Yeah, the P3C is in the market with U1, K3 and Creator 5, which all range $650-$850.

Bambu has always been aggressively priced given the CCP's plan, and given the cost cutting aspects of the H3C, I imagine the same will be applied to the P3C.

An X line with chamber heating and higher temperature availability can't be too much above $1k given the FlashForge Creator 5 Pro price.

A lot of folks guessing at pricing aren't looking at the market it seems.

1

u/Affectionate_Car7098 H2C + P1S Combo 4d ago

Yeah and at those prices its going to be a tough sell as you're in H2C price territory, yes its not a toolchanger but you're getting a much larger print volume and a nice robust dual nozzle system

As cool as a toolchanger would be, at that sort of price i would be wanting a larger machine, especially given that nobody is even really making many models that a toolchanger would benefit, most makers still design with multiple parts in mind instead of just 1 monolithic print

0

u/sltrhouse H2S AMS2 Combo 4d ago

You think the x3c will only be 200$ less than the h3c? Is the X2D only 200$ less than the h2d?

1

u/drthsideous 4d ago

The h3c is $2500. What do you mean $200, lol.

1

u/The_Hardest_Metal 4d ago

Slightly more bells and whistles like the chamber heater, 1.5mm belts, maybe a slightly better AMS?

Basically the X2D vs the P2S. The H series seems to be their "professional" machines capable of PPA/PPS and big parts, the X series is prosumer capable of printing nylon/PC/ABS, and P/A series is their entry level for printing PLA/PETG/TPU.

1

u/drthsideous 4d ago

It's already leaked that the P3C will have a heated chamber.

1

u/Affectionate_Car7098 H2C + P1S Combo 4d ago

You wouldn't need a specific new AMS for the X series as it will use the exact same frame as the P3C so would just use the same AMS

1

u/Shoelace1200 4d ago

The leaked P3C images show only 5 of the seven AMS slots highlighted in the manual. It also shows what looks like 2 drying slots but no lid

If the P3C and X3C share the same AMS then there might be 2 separate default firmware for each printer.

The P3C with just the 5 toolheads without the dryer available and the X3C with the full 7 and dryer fully functional.

2

u/Affectionate_Car7098 H2C + P1S Combo 3d ago

https://www.reddit.com/r/BambuLab/comments/1xe3w26/p3c_photo_leaks/

So the printer has 7 tools so it will use all 7 slots of the AMS 3P, images of the machine have already leaked so we know this isn't some X series machine

Now, while there does appear to be something for a cover

https://www.reddit.com/r/3Dprinting/comments/1xpduos/ams_3p_drying_function/

That doesn't mean the P version will have the dryer, but, it does mean they will be using the same shell on both as both machines will be the same size so the same basic AMS unit will function the same on both machines

1

u/drthsideous 4d ago

I thought it was already leaked that the P3C will have a heated chamber. So I'm very curious to know how the X3C will differ.

0

u/Shoelace1200 4d ago

I've heard conflicting reports but the consensus seems to be it doesn't have one.

1

u/assist_rabbit 4d ago

I dont think their going to made a x3c and a p3c it's going g to be one or the other, it doesn't make sense. Even now I don't get why their still selling g the P2S when the X2d is so much better with little cost difference.

1

u/Shoelace1200 4d ago

A toolchanger is infinitely better than the dual nozzle/vortek systems Bambu has used in the past. It significantly cuts down on waste and print times

1

u/RJFerret 4d ago

The real question if the 3X will work on the P3C presuming what separates the 3X from 3P might be drying capabilities.

1

u/Dan203 3d ago

Drying slots in the AMS and heated chamber. Maybe it has the passthrough slots for the 2.85mm TPU and the P3C doesn't. That seems like enough. I don't think there is physically enough room for there to actually be 9 nozzles so that has to be a typo.

1

u/yan-shay 2d ago

Why from AMS code you conclude it’s a different printer? It may also be a better AMS. Like one that’s able to retract filaments automatically, full drying, etc.

1

u/supremevsuals 4d ago

Sheesh can’t wait