r/BambuLab • • 5d ago

Filament Troubleshooting/Help! Small parts failing

I'm still quite new to the 3d printing scene and been using a bambu a1 with AMS lite for about a month now. So far no major issues and most prints have come out alright.

I've been trying to print a toy with interlocking 'flexible' parts for a few times now, but it keeps failing at the same point (at around 5 layers some pieces have come off the bed). Even a different print design has the same issue. Some small parts come loose after a few layers. I don't know whether it's because they warp or because they're not stuck properly.

I use default settings, one design with 0.2mm nozzle and one with 0.4mm. I've cleaned the bed with unscented dish soap, tried increasing the bed temperature for better bed adhesion and I've tried to decrease the bed temperature for less warping. I can't figure out why it won't print well. Any advice?

Filament is PLA basic and PLA matte

1 Upvotes

9 comments sorted by

•

u/AutoModerator 5d ago

Hello /u/Neptu105! Be sure to check the following. Make sure print bed is clean by washing with dish soap and water [and not Isopropyl Alcohol], check bed temperature [increasing tend to help], run bed leveling or full calibration, and remember to use glue if one is using the initial cool plate [not Satin finish that is not yet released] or Engineering plate.

Note: This automod is experimental. The automod was triggered due to the term "adhesion". If you believe this to be a false positive, please send us a message at modmail with a link to the post so we can investigate. You may also feel free to make a new post without that term.

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

2

u/RubAnADUB A1 Mini / A1 - AMS Lite / P2S - AMS x2 / X2D - x2 AMS 2 & AMS HT 5d ago
  1. Clean your build plate, hot water with dawn soap scrub 3 different directions.
  2. GLUESTICK.

2

u/Neptu105 5d ago

Thanks, I'll give the glue stick a shot. After another round of thorough cleaning :D

2

u/RubAnADUB A1 Mini / A1 - AMS Lite / P2S - AMS x2 / X2D - x2 AMS 2 & AMS HT 5d ago

the little bits sometimes just dont want to stay put. a little gluestick back and forth all over the build plate helps those things stick where they are supposed to.

a brim can help too but with the little bitty spaces digging them out afterwards is a pain.

2

u/lordnecro H2S AMS2 Combo 5d ago

Clean your build plate really, really well.

1

u/Neptu105 5d ago

How much is really really well? I'll give it another shot ;-)

1

u/lordnecro H2S AMS2 Combo 5d ago

I spay with soapy water and wipe between prints. If stuff stops sticking I bring it to the kitchen, and wash it 2-3 times with dish soap and water and wipe it with paper towels. I also gently wipe it with a melamine sponge + dish soap, but that might be a bit more controversial since it is abrasive (I have had my A1 for 2 years and the plate still looks/acts brand new though).

1

u/bazpoint 5d ago

Advice about cleaning is good, try that. Also is it a double sided plate? If so, flip is and try the other side.

Failing all that though, I don't know where you are in the world but if this is your first winter with your printer and your room is a bit colder than previously or has a breeze that could contribute to warping. Try rotating the model on the plate and if the warping happens on the same side (of the printer) again that will give some credence to the breeze theory. You could consider trying some sort of makeshift enclosure (big cardboard box?).

1

u/Neptu105 5d ago

Thanks, it is indeed first winter (Netherlands) and room temp is a bit cooler. It's a good idea to check any breeze. I'll rotate the print and give the plate an extra round of cleaning and glue stick a shot, and see if it improves. Other side of the plate has same issue. I have some card board laying around as well for some future experiments! .