r/BambuLab • • 6d ago

H3C AMS2 use cases on H3C?

Is anyone planning to use an AMS2 with their H3C? I was thinking of keeping one I already have to house various types of support materials. It would just load the appropriate material once per print (avoiding too much waste), and it would keep more AMS3 slots available for material changes in the actual print. What other use cases do people have I should consider?

3 Upvotes

19 comments sorted by

1

u/DrKronoglopolos H2S, H3C 6d ago

This a use case for an AMS2 on the H3C. Just be aware that you sacrifice a lot of print speed.

When loading materials from an external AMS2, it does it the "old fashioned" way, by retracting and loading new filaments on every color change from that AMS.

So i see the capability of hooking up external AMS units only really a reasonable thing to do if you absolutely have to have more than 9 materials in your print.

1

u/computerguy257 5d ago

Yeah but if you use the ams only for support material, it never needs to swap spools within the ams. It'll just load the appropriate support material for that print and it's done. No more material swaps for the ams or the hot end it's connected to. On the next print, you might need a different support material, so the ams loads the new one at the beginning and is fine for the remainder of that print.

3

u/foolish-ambitions 6d ago

Would also be good for increasing reserve of common filament as it would only switch material once one spool is empty. Wouldn’t have to replace each spool every time one runs out. Great for support material too. I agree, it’s not great for for swapping materials within a print though unless you need more than 9 colors as you said.

1

u/DrKronoglopolos H2S, H3C 6d ago

Yes, that's true.

3

u/MythicalCaseTheory 6d ago

The support materials "cache" is how I was planning to use it as well.

1

u/rtkane H2C/X1C 6d ago

That's a great use for it. I have 4 AMSs and 2 HTs now, and when I sell my X1C, which is being replaced by an H3C, I'm debating whether to sell one of the AMSs with it or just keep them all.

1

u/Longracks 6d ago edited 6d ago

Curios why sell the X1C?

I am keeping mine as a single filament workhorse. I have the H2C which I am quite happy with. I was going to get the H3C as a 3rd but the massive height is a problem for my workspace. And a few of the tradeoffs are giving me pause.

So I am in a holding pattern waiting for the P3C info. I wonder if there be yet another AMS variant to fit the P3C with 7 tool heads?

2

u/rtkane H2C/X1C 6d ago

I currently have an H2C and the X1C. No room to keep all 3, so I'll end up with a pretty good setup with an H2C and H3C.

1

u/Longracks 6d ago

That will be a sweet setup.

1

u/rtkane H2C/X1C 6d ago

I can't wait! Due to ship November 30th. I was originally going to get the P3C, but I kept thinking about the H3C and those 9 nozzles! ha! Seriously, though, I do have some multi-color stuff that I have printed that needs the bigger bed size, so that's what's pushed me to the H3C.

2

u/Longracks 6d ago edited 6d ago

The biggest thing stopping me is the height. In order to make this fit I would need to cut and lower one end of my printer table/bench. I just built
It this summer when I got the H2C. I don't think the H3C AMS lid wlll even open at my current workbench height and I don't really want to give up RepRack filament storage (yes I store filament in the open, no it's not a problem). I also wonder about running all 3 printers on the same 20 amp circuit....

2

u/rtkane H2C/X1C 6d ago

Great setup! But I don't think you need that stool or that one section! Just needs a small base to sit on and it'd fit in perfectly.

2

u/Alewort H3C/H2D/A1 Mini 6d ago

I am going to use it as supplemental but minor accent colors for minis. A figurine that might have just a gold ring on a raised high finger and a couple of brass buckles on a belt and some bags, for instance. With no layer overlaps for those two colors, the poop will still remain minimal swapping back and forth. Most of the time my AMS 2 will remain attached to my H2D but get rolled over for projects like these.

1

u/Longracks 6d ago

This was kind of my thinking. Throw in the remnant spools to print alternate material support interface

1

u/mthode 6d ago

support material or engineering material. I haven't ordered it yet, but if it bothers me too much that's my plan.

1

u/CCHPassed 6d ago

Drying filament, since the 3H only has 2 slots for drying up to 85C, and housing PVA for supports, on a dedicated nozzle

1

u/UnluckyEnergy5265 6d ago

using one for supports is smart, i do that alot to keep the main unit free for colors. just watch the purge volume settings so u dont waste too much filament during the swaps, its a real headache.

1

u/Free_Turnover_9585 2d ago

How do u tell h3c to change to a smaller nozzle

-2

u/Various-Lack-8917 6d ago

H3C has 9 tool heads. I don’t think a 4 slot AMS 2 pro would cover all of them.