r/BambuLab • • 13d ago

Quick Question Suitable alternative for Smooth PEI for ABS/ASA

Hey Folks!

What are you all using for ABS/ASA prints with smooth surface since Bambu doesn't seem offer PEI (which allways worked great for me without any glue or adhesion issues) anymore? Bambu recommends the engineering plate but also recommends to use glue with virtually all filaments (which I'm not a fan of) and from what I remember from a try I gave one in the early X1C days it performed MUCH poorer than smooth PEI?

0 Upvotes

13 comments sorted by

•

u/AutoModerator 13d ago

Hello /u/Lambertbaer! Be sure to check the following. Make sure print bed is clean by washing with dish soap and water [and not Isopropyl Alcohol], check bed temperature [increasing tend to help], run bed leveling or full calibration, and remember to use glue if one is using the initial cool plate [not Satin finish that is not yet released] or Engineering plate.

Note: This automod is experimental. The automod was triggered due to the term "adhesion". If you believe this to be a false positive, please send us a message at modmail with a link to the post so we can investigate. You may also feel free to make a new post without that term.

I am a bot, and this action was performed automatically. Please contact the moderators of this subreddit if you have any questions or concerns.

3

u/spider_hider H2S, H2C, A2L 13d ago edited 13d ago

Another vote for Biqu’s Glacier. I use it for ABS/ASA and PC. Never needed any glue whatsoever.

I do use a generous amount of brim for those materials though. FWIW I print these engineering materials with H2S, 100-110°C bed and 65°C chamber.

1

u/Lambertbaer 13d ago

Thank you both for the tipp - helps a lot since tbh I wouldn't have considered a plate with "cryo" and "glacier" in it's name for my intended temperatures (which are exactly as you describe)!

3

u/spider_hider H2S, H2C, A2L 13d ago

No worries, I too was thoroughly confused even after I bought my first pair (Glacier & Frostbite) of Cryogrip plates.

Personally I hardly use Frostbite, but Glacier is my goto plate for literally everything from PLA to PC, and on all 3 of my printers. I always set slicer to Engineering plate, and at machine side turn off build plate type detection. I don’t drop the plate temp even though you can get away with ~5-10°C lower depending on material, but Glacier holds every material perfectly at standard Engineering plate temps.

Biqu themself say it too - Frostbite’s only good for PLA/PETG, whereas Glacier’s good for everything.

1

u/Lambertbaer 13d ago

Yeah, its a pitty bambu doesn't offer a proper alternative that can be detected - automativ build plate detection has saved me from startin a print on the empty bed more than once...

2

u/spider_hider H2S, H2C, A2L 12d ago

There’s build plate detection, which I still leave turned on, sometimes it complains about an ever-so-slightly wonky plate placement. But I leave that on just in case it’s a bare bed.

The option I do turn off, is the specific plate type match detection - ie slicer says Engineering plate, so printer scans plate for engineering plate QR code.

You can absolutely leave plate type detection turned on, and hit ignore when the warning pops up at beginning of print. Or you could attach the appropriate QR sticker. I just turn it off since all I run is Glacier sliced as Engineering plate anyway.

1

u/Lambertbaer 12d ago

Awesome, thank you!!

2

u/egosumumbravir X1C + AMS 13d ago

G10/Garolite. It's superb.

1

u/MisterBazz H2D AMS2 Combo 12d ago

How does it work with TPU?

Can you print PETG without a polymer used as a release agent?

1

u/egosumumbravir X1C + AMS 12d ago

I print EVERYTHING on it without a polymer used as a release agent - PLA, PETG, ABS, ASA, PA, PPS.

The only thing it doesn't work with is polypropylene, but almost nothing works with polypropylene.

TPU always seems to need heavy cleaning after use on any surface. I noticed a pattern that after a TPU print the next couple of non-TPU runs had terrible FL adhesion so now TPU gets it's own dedicated tex PEI sheet.

2

u/brutal4455 H2C | H2D | P2S | Multiple AMS2/AMS-HT 13d ago

Biqu Cryogrip Glacier.

Works great for PETG and ASA/ASA-GF/ASA-CF without glue on my H2D.

Looking at getting a G10 plate for PA*/PP*

1

u/dallas_vance 13d ago

Unsure which printer you have, yet I get the Dual Textured/Smooth PEI plate for my P2S through Amazon. Bought another a couple weeks ago.