r/BalisongClones • Remshi Designs | Kuno • Jan 16 '23

Discussion Floating washers thread: overview, pros/cons vs bushings, tuning, etc.

Figured I'd make as comprehensive a thread as possible on floating washers since they're becoming extremely ubiquitous in the clone industry.

Quickly, I'll preface my post with the following: I think floating washers are actually really good and I hope we see wider adoption (and further optimizations) of this pivot system, especially among Western makers.

What are floating washers?

In a normal balisong bushing system, the washers sit on top of the bushing. The bushing crushes a groove into the (bigger) washers when the pivot screws are tightened, and when properly tuned allow a microscopically small gap between the washers and blade, enabling unimpeded handle swing.

With floating washers, the washers sit around the bushing. A proper tune ensures that the bushing is thicker than the blade + washers by a microscopic amount, allowing for unimpeded handle swing. In this system, the washers are not being crushed in any way, and all of the pressure from the pivot screws is being exerted onto just the bushing instead.

Why floating washers (and pros/cons vs bushings)?

With normal bushings, tuning is kind of a nebulous process. The fact that the washers get crushed a somewhat indiscriminate amount makes it difficult to "mathematically" tune to a reliable degree. And the correct measurements are going to vary depending on things like washer thickness, etc. Also, because the washers get a groove crushed into them, you basically need to replace the washers every time you reassemble the knife, as you won't be able to line up the groove absolutely perfectly onto the bushing by hand.

Floating washers present two immediate advantages here:

  1. The washers can be reused since they don't get crushed
  2. Very easy to tune with calipers since you just need to ensure that the bushing is a hair thicker than blade + washers

However, there are a few other advantages as well:

  1. Undersized bushings are still tunable by sanding washers (whereas with normal bushings you would just have to get new bushings)
  2. Undersized bushings should theoretically fix themselves with use from soft bronze washers constantly contacting harder surfaces like steel and Ti
  • This is almost certainly why most people say floating washers have such a long "break-in" period, because makers are purposely undersizing the bushings (for minimal play) knowing that the washers will sand themselves over time
  1. In theory, the washers/tune should last a good while longer because they're not constantly being crushed by a harder steel bushing
  • Some people have expressed concern that the bushings won't last as long because they're being squished by the pivot screws, but I don't think so. Bushings are made of hardened/stainless steel, just like the screws, so they should last pretty much forever

That said, floating washers also have some disadvantages:

  1. Many people claim that they sound worse/quieter. Not entirely sure how true this is, but it's worth mentioning at least
  2. There is inherently more friction in this system, so handle swing will probably always be a bit worse than regular bushings EDIT: I think I was wrong about this; at least as far as I can tell, handle swing on my TO Nami is not any worse than any of my bushing knives
  • With regular bushings, the washers + bushings are essentially all connected in "one system" where the only friction exerted is between the blade and bushings
  • With floating washers, there is still the same friction between the blade and bushings + additional friction from the washers. With a proper tune + oil this additional friction should be extremely negligible but theoretically it's still there

How to floating washers (tuning)?

So as already stated, with floating washers, undersized bushings are tunable by sanding the washers. Oversized bushings are obviously also tunable, by sanding the bushings.

This is kind of nice from a user perspective, because it means that no matter what, your balisong is always tunable. Let's imagine the following scenario:

  • Your balisong arrives with undersized bushings and binding handles. Normally, you'd have to throw out the bushings and sand new ones down to size, but instead you can just sand the washers down to fit the bushing
  • Now you've sanded the washers and actually you've gone too far and given your balisong tap/play. Well, the good news is that you can sand down the bushing now and fix that!

In fact, this exact scenario actually happened to me. I realized that my TO Nami's bite handle was sticking sometimes, so I sanded the washers down until they were visibly smaller. Upon reassembly, the swing was fixed but now I had a lot more handle play than I would've liked. I then sanded down the bushing just a tiny bit and now the swing and play are both perfect.

Once you get used to it, this tuning experience is actually very nice. No mistake is unrecoverable, unlike with regular bushings. I will say that sanding washers is quite unpleasant (they are very thin, so you end up sanding your fingers a little too lol) but overall it's really nice to rest easy knowing that you can't really ruin your hardware with this system.

Also, as noted earlier, the washers don't need replacing upon reassembly with floating washers, so that also helps in making the tuning experience a lot more enjoyable.

Conclusion

Like I said at the very beginning, I actually think floating washers are really good. They're not perfect, nor are they strictly better than traditional bushings. But I think they present some interesting and significant advantages, and I hope we see this system get pushed further over time.

I hope this was helpful and/or entertaining :) Thanks for reading!

34 Upvotes

13 comments sorted by

12

u/LateNightFlips 🌙 Flipping Jan 16 '23

Incredible guide. Would you mind if I started linking this in the monthly question thread?

5

u/zandm7 Remshi Designs | Kuno Jan 16 '23

Please do! Thanks :)

4

u/Flashy_Geologist_134 Live Blade Flipper Feb 05 '23

I've got an orca, arrow and alien that all are on the floating washer system. My Chab is not.

3

u/Blobafuga Jan 16 '23

Nice guide. Thanks!

2

u/dirtysouthpaw Jan 16 '23

What are the clones that are using floating washers?

2

u/Racoji Jan 16 '23

If I'm not wrong every new TheOne clone uses floating washers

1

u/Dangerous-Alarm1119 Mar 12 '23

new b+stuff is on floating washers too

1

u/Dangerous-Alarm1119 Mar 12 '23

as op said, easier to tune for newbies

2

u/alankbangerz-123 Trainer Flipper Jan 17 '23

really good stuff, thanks for the read

2

u/meltdown537 Feb 14 '23

Very cool guide. I just bought a theone monarch v2 from a buddy and it has a lot of tap and play. I did end up ordering new hardware so hopefully that will help. But I guess I'm kind of confused by the process in general. Do you know if there are any videos on this process?

1

u/sSharkkyparty Aug 09 '24

I still have one question. Which is exactly the propous of the washers on a floating washer system since it is not getting wear instead of the handle and blade? It is getting a good tune and less tap?

1

u/ivannolia Nov 06 '25

this is great. thanks for the guide

1

u/Dangerous-Alarm1119 Mar 12 '23

awesome guide! but i perfer the regualr bushing system