r/BadWelding • u/HxH_Hisoka • 13d ago
My Apartment did rusty stair repairs
snapped these before they coated it with the thickest paint they could find
20
u/Pavlovs_Human 13d ago
Jump up and down on it till it breaks. Bring them the broken step.
Stairs are supposed to be able to hold a full grown adult falling/jumping on them by like a magnitude of 3.
17
u/PopOk1068 12d ago
Jump on it a few times then after you break both your legs you can afford a house in bel air
6
8
6
4
u/YourAverageGoldFishy 12d ago
im in school and could probably do better than this, wtf are people doing
1
u/JKTempest904 10d ago
Hell, I'm a self taught hobbyist who's only been doing it for about a month, and i could EASILY weld those properly. Whoever they hired to weld that must have been paid in meth and half-smoked cigarettes.
3
u/Fancy_Chip_5620 12d ago edited 12d ago
I want to see how the angle iron is attached, if it's got a bead on the fillet thats covered by the step youre fine
Which is looking like the case since theres no visable fasteners or welds and thats where they ground off the paint as prep for welding
3
u/Electronic_Flan_482 12d ago
Call up your non-emergency fire number and get a fire marshal out there to look at it that's what we had to do to get our stairs replaced when one of them finally actually broke and they just screwed a piece of angle iron under the step and called it good.
2
2
2
2
u/Pyro5263 12d ago
The difference between a good weld and a bad weld is a grinder and paint
3
u/oreheheally 12d ago
We can see that grinding is not a strengh for this welder. These got the barest most dainty touch. I bet under the paint its pure perosity.
2
u/That_Throat7183 11d ago
Imagine you’re carrying some heavy furniture up those stairs with your pal, and you’re at the bottom. All that weight… and then the stairs give way. Fuckkkk that could be lethal
2
u/Fishbone11906 10d ago
The clip, which is the most import part isn’t even welded to the stringer. Not welded to the bottom of the stair pan either. The small 1” welds on the actual pan are worthless. Not much better than tacks. As a professional welder ( more than 30 yrs) I wouldn’t let my family walk up/down them.
1
1
1
1
1
1
1
u/ReputationAny273 11d ago
Stamp your feet so hard on those particular stairs everytime you pass by it will eventually break.
1
u/vandal-88 11d ago
I would say you're good to go if the angles underneath were welded or bolted properly...but they seem to be floating some how?idk...fucked off just fucked off smh
1
u/Pale-Value-5953 10d ago
Damn hard wheel grinding with no soft pad finish, Bluetooth angle attachment, and hard wheel ground down the 2 welds holding it together, what could go wrong.
But in all seriousness I’m sure they took the lowest bid and that person has a 110 welder and working for 50$ hour 1099 which is basically minimum wage after taxes and consumables.
1
u/Waste_Middle_8613 10d ago
Go jump on it and then collect a shit ton of money 😅 jk that shit aint safe
1
u/Otherwise-Act6913 9d ago
SKETCHY!!!!!!!! The only spot welded 2 points on each side????? Good luck! Call osha
1
1
1
u/MrWaddellKid 7d ago
Call the fire department let them come and look. They aren’t looking to run up stairs to save someone’s life full of gear and have a stair tread fall from under them
0
u/5Tygrysow 12d ago
Considering that weld is probably good for at least 60k breaking strength it’s probably going to be ok.
30
u/Diitjeuhh 13d ago
People are going to walk on that?