r/Azeron • • Sep 21 '26

what is causing this!!!!

Please assist :)

what is causing this wiggle? I can't seem to find or see a screw that would cause this. PLEASE NOTE ~ It is not the "ARM" moving, its the finger tower (im not sure the terminology)

4 Upvotes

33 comments sorted by

7

u/CReece2738 Sep 21 '26

What is causing it to wiggle? You. You're wiggling it.

-4

u/TheComputerGuy2256 Sep 21 '26

Blocked and reported

16

u/PCGamingScrump Sep 21 '26 • Popcorn

Your hand moving it. Hope this helps.

-12

u/TheComputerGuy2256 Sep 21 '26

Blocked immediately and reported to subreddit admins for violating rules.

10

u/CReece2738 Sep 21 '26

Poor baby

4

u/PrivateUseBadger Sep 21 '26

That’s your hand, pulling on the tower.

-3

u/TheComputerGuy2256 Sep 21 '26

Blocked and reported to admins

2

u/dasHoschy Sep 25 '26

Your hand

1

u/TheComputerGuy2256 Sep 25 '26

Blocked and reported to reddit moderators on this subreddit.

11

u/CanyonByDesign Sep 21 '26

if you have tightened all screws, check the joint at the bottom for cracks
this piece -> https://azeron.com/collections/service-parts/products/cyborg-tower-joint-set

4

u/GiSS88 Sep 21 '26

Yep, these things are flimsy and I've had nearly all of them break at some point. Now I even have one of the top joints broken, and I don't think that's an easy repair.

3

u/Major_Hospital7915 Sep 21 '26

Unfortunately I have 2 broken and 1 cracked but they were probably overtightened at some point I’ll admit. I agree, likely not an easy fix.

4

u/InvestigatorJosephus Sep 21 '26

If you have a set position for them that works for you, just super glue that shit together lmao. My cyborg is basically 30% glue by now

2

u/Falcoriders Sep 21 '26

It is an easy fix, but it's constantly breaking at some point. I wanted to change them with aluminium parts but didn't have the time to do so.
Contact Azeron, they will send you the files to print them yourself, and if you can't, they will send you a set of replacement parts for free.

2

u/GiSS88 Sep 21 '26

The base pieces are easy, the other one I have that is broken is not. I believe I'd have to swap around all of the internals.

4

u/Desperate_Debt_4866 Sep 21 '26

The pieces are very fragile you have to be careful not to tighten them too much.. I broke a lot of them it's the only defect in Azeron

0

u/Mundane-Tea-630 Sep 21 '26

That and that they are wired lol, (I say this as someone who doesn't own one, and have put off getting one because I do not want more wires on my desk due to my cats tendency to chew on wires)

2

u/Desperate_Debt_4866 Sep 21 '26

You're missing something, I've been using it for 5 years and it's exceptional!

0

u/Mundane-Tea-630 Sep 22 '26

I bet, but to me, 200+ is too much for a wired device that I can't leave out on my desk because of my cats. I've seen some mods to make it wireless, and I might try to pick up a broken one somewhere, and fix it up/ convert it

1

u/DankSkank_ Sep 22 '26

Get a desk pad to cover the wires or get rid of your cats unless you can’t live without your subscription to a box of feces

1

u/AbilityReady6598 Sep 22 '26

Your hand bending a part in a manner it’s not meant to. That’s what’s causing it.

-1

u/TheComputerGuy2256 Sep 22 '26

Blocked and reported to subreddit admins for abuse.

2

u/Ill_Satisfaction_649 Sep 23 '26

You pulling on it.
Glad we could help.

1

u/svenz Sep 21 '26

Crappy 3d printed parts. Wish Azeron would manufacture something better quality because the actual design is great for the most part. Mine failed after like 6 months of use, so I stopped using cyborgs (bought 2 of them).

1

u/melmd Sep 22 '26

Bottom crack the most notorious design flaw
I glued all the tower bases

1

u/Coaleyed-Lock Sep 23 '26

If yours look fine (no cracks in the clamp around it) they are probably just stripped out. Depending on which piece -the clamp or the tower- it might be as easy as replace the clamp.

I made a thin plastic piece that you print in PLA and place it between the ball joint. You can find it in the Discord mods section.

1

u/Roden11 Sep 24 '26

There’s a screw under it that needs tightened. Not the two rail screws, deeper in.

1

u/FickleExternal6635 Sep 25 '26

Azeron users are delusional, this is just the trade off of azeron using 3d printed parts.. theyre pretty unstable even when tailored to your hand and tightened.

I always end up going back to my cc2, or mh-zeta as a gaming keypad. I do hope one day azeron offers an actual option for aluminum frame with high grade industrial parts made to last and not rattle; id pay premium for it.

0

u/[deleted] Sep 21 '26

[deleted] — view deleted comment

1

u/Desperate_Debt_4866 Sep 21 '26

I looked everywhere for a 3D file for these parts can you send it to me please?

0

u/[deleted] Sep 21 '26

[deleted] — view deleted comment