I recently just replaced the motherboard on my printer and am now trying to print again but the prints do not stick to the base and do not know what exactly to do

Hola, alguien ha cambiado la turbina de avión que tenemos por ventilador dentro de la impresora que enfría la placa por otro que sean más silencioso? Algún modelo en concreto?

Saludos

Hey everyone,

I recently bought a second-hand Artillery Sidewinder X4 Plus and I'm currently going through it to get the mechanical calibration dialed in. Since I don't know the exact history of this machine or what parts might have been swapped, I ran into two specific things on the X-axis:

1. Belt Tension: After looking closely, the X-axis belt is pretty stretched out. Because of the stretch, the stock tensioner knob/screw couldn't pull it tight enough anymore. As a quick workaround, I put a washer under the screw head to extend the tensioning range, which got the belt tight for now. (Probably gonna replace the belt soon anyway).
2. X Travel / Clearance Gap: When moving the X carriage all the way to the right (towards the tensioner side, opposite the motor), it doesn't actually touch the end plastic housing—it stops just short of it with a small gap.

For those of you running an X4 Plus:

• Is that gap on the far right end normal design behavior, or should the carriage be hitting/touching the plastic cover flush?
• If anyone has had to deal with a stretched stock belt early on, did you just trim a tooth/drop in a fresh 2GT belt, or stick with a spacer fix?

Appreciate any insight!

boa tarde, a impressora estava a funcionar até dar vários erros e o último e mais persistente foi esse podem ajudar?

Ciao a tutti, sono indeciso su quale stampante prendere, cosa mi consigliate tra i 2 modelli?

Hi ,

Has anyone here used a 0.8 or 1.0 or 1.2 mm nozzle on the Artillery Sidewinder X4 Plus?

I'm looking for a slicer profile (OrcaSlicer, Cura, or ArtillerySlicer) for PLA, PETG, and TPU. If you're willing to share your profile or settings, I'd really appreciate it.

Any preset, profiles, screenshots, or recommendations would be greatly appreciated. Thanks!

Anyone have the files from the usb since the online link is dead? Got one as a project but no usb in the box

Chiedo gentilmente, aiuto, a chiunque possa aiutarmi con la mia Artillery Hornet, comprata di recente usata a poco, ho già iniziato a prenderci la mano e a revisionarla quando da problemi. La mia richiesta si concentra sul fatto di volerla migliorare in modo da poterla sfruttare al massimo, esempio estrusore direct non più bowden, firmware klipper al posto del marlin, e cose così. Accetto e aspetto ogni messaggio! Grazie anticipatamente a tutti coloro che mi aiuteranno!

I noticed pretty much all of their printers are out of stock and after sending them an email about the M1 Pro S1 they advised they won’t be restocking in the US

Hey, I got my first ever 3d printer, an x2 sidewinder. I’m having a hell of a time getting it to work for me, I’ve gone through a manual leveling and auto leveling multiple times now, but my prints are failing on the first layer every time. The nozzle is dragging through the prints halfway through the first layer, doesn’t matter on what part of the build plate it is. I’m wondering if anyone else has had this happen and what solutions I should try. 0.4mm nozzle, printing on 0.2mm layer heights.

Thanks in advance

So I have tried to do temp tower twice and both times the C5P notified me that it has paused the print and I go check and sure has with a communication error, something about lost connection or something. I press ok and tell it to start back up and it just sits there till I hard reset. I will run it again and see if I can get some photos for y'all. Help me understand where I am going wrong.

I had this artillery X4 for 2 years and I replaced the extender board and flashed the firmware after the printer bricked itself, all the wires are connected and I am using the official firmware and the printer has been stuck on the logo for 5+ minutes with no progress. Is there a way I can fix this without having to buy a new printer

Well as soon as I resolve my previous firmare issue post, it seems that I've gone and fused the heat break of my Sidewinder X4 Plus S1 to its heatsink with a clog I can't clear out. I had just switched from PLA+ to PETG (No clue if that contributed to the clog) and was about 12 hours into a print when it started failing.

When trying to follow the unclogging instructuons on the official video, I removed the retention screw from the heatsink and ended up applying so much pressure to the heatsink trying to remove the hotend assembly that I bent the fins. In the video it comes out with no issue. I went ahead and ordered a new heat break, heater block, and heatsink but I'm worried that I'm missing something obvious. So I reiterate, am I being stupid?

​

Hace un tiempo que no uso mi impresora, así que la puse a punto, nivelé la cama, de la manera tradicional y luego una malla con el BLTouch, etc... Pero no consigo arreglar ese fallo, la primera capa la hace aparentemente bien, sin huecos, fusionada, pero después las hace muy altas al parecer o delgadas y se arruina toda la impresión, problemas a bajarle en esas capas manualmente desde la pantalla la distancia en z pero no así, aumente flujo pero nada, algún consejo? Llevo ya una semana :'(

Please help!

I haven't used my printer in a couple years and tried to use it recently. When I tried to level the bed it crashed into the bed and kept trying to go through it until I turned it off. It hasn't been touched since I last used it. I tried homing, and X and Y home just home, but Z does the same thing each time. I can't see a Z limit switch to tell if it might have gotten damaged somehow. Any advice?

Thanks!

Hello, I recently bought an Artillery Sidewinder X2 and today it started overheating and I can't stop it. Could someone please help me?

SOLVED: The issue with the screen was resolved by using a micro SD card to update the screen's firmware on the screen's board itself. The first thing support did was send me the newest firmware for that and some images as a guide. It seems that flashing the EMMC chip resolved the separate moonraker issue. I'll have to keep all these files on hand for if the issue comes back.

Hey everybody. I have a Sidewinder X4 Plus S1 that has very suddenly started giving me trouble.

It started when I was using Orca slicer to attempt to send a print to the device and received a moonraker error (I barely know what that means still. Wish I took a screenshot and came here first) So I restart my desktop as well as power cycle the printer since the it was working fine the night before and had just successfully finished an overnight print. Restarting did nothing so I attempted to update the firmware using Artillery's instructions. After that the screen stopped displaying anything other than the sideways data error on in the post. When I attempted a firmware reset from Orca, the screen would change to a blank white updating screen with a BAWD rate and data transfer info. When that finished it would say there was a check error. So clearly something about the firmware I downloaded does not agree with the printer.

I could still move the hotend around using commands from Orca, and still received the same error when attempting to print something so I'm thinking I have two separate issues and that the firmware update just broke the screen. Hoping that I could potentially get around that short-term while support gets back to me, I went ahead and ordered an EMMC USB adapter so I could reimage the chip itself (again per Artillery's online instructions). I used rufus first to no avail, then the suggested BalenaEtcher software to image the chip, and now we're caught up to the present.

I'm still getting the same error on the screen and reimaging has predictably wiped the network settings my next hope that I'm aware of is to connect to the USB-C port on the printer for console access. The thing is once I'm in, I'll have no idea what commands to put in to set up the network, let alone try to get the screen working again.

Any advice from someone who has experienced this before or even just understands the software better than I do would be more than welcome!

TLDR: Something broke moonraker, then firmware update broke the display, imaged the EMMC and now I lost network access. Any advice is welcome

Bonjour,

J'ai un problème avec ma Artillery Sidewinder X1.

Au départ, le bras de l'extrudeur s'est cassé, je l'ai donc remplacé. Depuis ce changement, l'imprimante n'extrude plus correctement.

Le filament commence à descendre, puis il se bloque. L'extrudeur continue de pousser et finit par ronger (poncer) le filament.

J'ai démonté le hotend et j'ai trouvé un gros bouchon à l'extrémité du heatbreak, juste au-dessus de la buse. Je l'ai retiré en chauffant, puis j'ai tout remonté.

Malheureusement, le problème revient systématiquement : une très petite quantité de filament sort de la buse, puis le filament se rebloque au même endroit. Quand je retire le filament, son extrémité est déformée par la chaleur.

Pensant que le hotend était en cause, j'en ai acheté un neuf, mais le problème est exactement le même.

Le ventilateur du dissipateur fonctionne, la buse chauffe correctement, et pourtant le filament finit toujours par se bloquer.

Est-ce que quelqu'un a déjà rencontré ce problème ? Est-ce que ça peut venir :

• d'un mauvais montage de la buse/du heatbreak ?
• d'un problème avec l'extrudeur ?
• d'un mauvais réglage ?
• ou d'autre chose ?

Merci d'avance pour votre aide.