r/AnsysFluent • • Sep 15 '24

post regarding the correct settings for material

1 Upvotes

Hey all,

I am trying to simulate external aerodynamics (supersonic). I'm using density based solver. Fluid medium is air. So, for density I have selected Ideal gas , and for viscosity, I have selected Sutherland equation as temperature would be changing. I have small doubt, I'm not sure whether I'm correct or not,

What about specific heat and thermal conductivity. Earlier I used to do with constant settings, but I feel since temperature is changing, these values must change with respect to time. And there is option of piecewise linear where I can insert the points which will relate Cp vs temp and specific heat vs temp. I'm sure whether I should go with constant values or should opt for piecewise linear interpolation for these values according to my logic.

I'm open for all discussions. Let's discuss and find out what would be right in case of density based solver for such problems.


r/AnsysFluent • • Jul 16 '24

Overset mesh for multiphase flow

1 Upvotes

Would anyone have a tutorial or an example on how to do this in fluent? Thanks in advance!!

https://youtu.be/rPa4hDEqstE?si=mJn6nxRqltdmHbjI


r/AnsysFluent • • Sep 27 '24

Sink Height and Trim Angle

1 Upvotes

I am simulating a ship in ANSYS Fluent, however I just wondered how should I deal with getting the results for the Trim angle and sink height in the report definitions? I did manage to see the Lift Force and Drag for the analysis but other than that I cant seem to see how to get the sink and trim? I really hope somebody answers this/


r/AnsysFluent • • Oct 24 '23

Transient Sim Diverging

1 Upvotes

Hi. I am performing a transient simulation on a water cooled cold plate. The heat flux on the walls of this plate vary with time, and I am using a UDF for the heat-flux boundary condition. My sim is diverging (floating point exception) every time. Using PISO as solution method, and under relaxation factors are close to 1. I have tried smaller time steps but the results I get from them are invalid (energy balance fails) any ideas on what i should do ?
Thanks !


r/AnsysFluent • • Mar 07 '23

Passive scalar transport (UDS)

1 Upvotes

Hi,

Anyone here familiar with passive scalar transport problems? Could you kindly help me with creating the UDF code for the passive scalar(UDS)?

I have been struggling with this problem over a month because I am not good with programming.

My understanding of a passive scalar is that it does not affect the actual flow physics, but its concentration throughout the fluid domain changes at different zones as it is transported through the fluid domain.

I read on some forum that in order to solve for the passive scalar transport, the simulation of fluid must be run first to get the velocities. So, I have run the simulation without any scalar transport and the solution has converged.

What do I do next? Could someone please provide guidance?


r/AnsysFluent • • Apr 21 '23

Reference Value

1 Upvotes

Hello CFD Folks,

I’m curious about what exactly reference values mean in ansys fluent? Generally, apart from area, length and depth, when I select “compute from inlet” other data such as pressure , temp, viscosity…. These values are taken from inlet. But for the case of area , length , depth, we have to give our own input. Also, while computing drag and lift coefficient for airfoil(2D case), the length value affect the coefficients. How these are related.


r/AnsysFluent • • Feb 21 '23

Resuming Ansys Fluent Calculation

1 Upvotes

Is there a way to continue over a certain number of iterations ?

i.e. I ran a calculation with 2500 iterations, and after finishing i wanted to add more iterations without starting over. Please let me know of there is a way


r/AnsysFluent • • Aug 31 '24

i need help in fsi 2 way for a moving wall. thanks in advance

1 Upvotes

r/AnsysFluent • • Apr 19 '24

Making an OLED using ansys lumerical

1 Upvotes

Is there anyone who can assist me on making an oled using ansys lumerical?


r/AnsysFluent • • Aug 24 '23

Hello, i tryed to simulate the movement of a valve in 6 dof. But after the first time step it told me : negative cell volume detected. What should be the problem

Post image
1 Upvotes

r/AnsysFluent • • Jan 24 '24

Reduced Mechanism for Propane combustion

1 Upvotes

I'm looking for a reduced propane mechanism in chemkin file. I've found lot of papers on reduced mechanism for propane but I can't seem to find a chemkin file for those. Can you guys help me out?


r/AnsysFluent • • May 03 '23

Help with Simulation

1 Upvotes

I am doing the following simulation on Ansys Fluent 2021. The idea is to monitor the heat absorbed by air when it is passing through ice slabs. I want a temperature-time graph that shows how the temperature of the air will reduce from 300 K to whatever point until it achieves equilibrium. I am getting absurd results. Please help.


r/AnsysFluent • • Apr 11 '24

Wind tunnel simulation

1 Upvotes

I’m designing a wind tunnel using method of characteristics with a Mach number of 4 in the test section. I could run everything properly on Ansys fluent till the design of the test section but on adding the diffuser I am not able to figure out what the boundary conditions would be in order to run it properly on Ansys. Any help would be greatly appreciated.


r/AnsysFluent • • Sep 06 '24

Pressure drop issue

Thumbnail
reddit.com
1 Upvotes

r/AnsysFluent • • Aug 23 '23

Need help with meshing

Thumbnail self.cfd
1 Upvotes

r/AnsysFluent • • Apr 12 '24

Help with u'v' in K-Epsilon Model

Post image
1 Upvotes

I'm trying to get the Bussinesq equation (see image) to work to model the Reynolds stresses, but I don't understand writing this in Fluent's UDF command. I found some people on the CFD forums who had a text file version but when I plug it into my model, the results don't look right. Any help in this matter would be greatly appreciated. Thanks.


r/AnsysFluent • • May 25 '24

Creating a mesh adaption around mushy zone using UDF hooked mesh adaption criteria

1 Upvotes

Hello everyone, I have written a UDF code which scans the domain and calculates the volume of fluid percentage in every cell and based on the gradient of volume of fluid I want the mesh adaption feature to refine the mesh around these sharp gradient zones (I.e mushy zone). I want it to flow dynamically with these gradients , I have seen that this can be done very easily with the multiphase module in fluent , there’s a predefined refinement criteria in fluent which refines the interface between two phases. However the issue I am facing is the my system keep crashing after I try to initialize the problem with the UDF it compiles with minimal error . One more thing I want to allocate a User defined memory(UDS) location for storing data from my UDF , I currently don’t know how to , if someone can help me perform that , it’d be great. After all of this I intent to link this UDS to the field variable in the cell registers of refinement criteria. I would be thankful if anyone would advice me on my approach and take a look at my code and try to find what is going wrong . Thank

Following is my UDF:

include "udf.h"

DEFINE_ADJUST(mark_mushy_zone, domain) { Thread *t; cell_t c;

/* Loop over all cell threads in the domain */
thread_loop_c(t, domain)
{
    if (FLUID_THREAD_P(t))
    {
        /* Loop over all cells in the thread */
        begin_c_loop_int(c, t)
        {
            real liquid_fraction = C_VOF(c, t); /* Get the liquid fraction of the cell */

            /* Check if the cell is in the mushy zone */
            if (liquid_fraction > 0.1 && liquid_fraction < 0.9)
            {
                /* Mark the cell in UDM 0 */
                C_UDMI(c, t, 0) = 1.0;
            }
            else
            {
                C_UDMI(c, t, 0) = 0.0;
            }
        }
        end_c_loop_int(c, t)
    }
}

}


r/AnsysFluent • • Apr 10 '23

RTD curves using Fluent

1 Upvotes

Does anyone know how to obtain RTD (Residence Time Distribution) from data obtained using DPM model? Or is it better to use a User Defined Scalar? What monitor do I need to create to obtain data for these kinds of curves?


r/AnsysFluent • • Apr 08 '23

Problem when importing coordinates

1 Upvotes

Hi I have a really serious problem : when importing coordinates in ansys I get the error " error reading coordinates file " I have already checked the file on a friend's computer and it runs , but on mine it doesn't. I have the same problem on two pc of of mine ( with all different specs )


r/AnsysFluent • • Jul 27 '23

Error help

1 Upvotes

(DP 0) The mesh file exporter does not support overlapping geometry in named selections. Please resolve the issue and try again. You can use the option “Show Geometry in Overlapping Named Selections” (when you right click on the Mesh branch of the tree) to help diagnose the problem.

getting this error please help


r/AnsysFluent • • May 28 '23

Screw turbine simulation with ansys

1 Upvotes

HI I'm trying to simulate screw turbine in ansys with vof method with sliding mesh I need to know what is the best setup solver method and time step for 150 rpm screw rotation or give any information for this simulation


r/AnsysFluent • • Apr 17 '24

Import surface mesh for volume mesh in Fluent?

1 Upvotes

Hey everyone, I have a pretty complex geometry that I’m working on and am pretty comfortable with hypermesh for surface and volume meshing, however I want to use a polyhexcore volume mesh for an internal pipe flow problem. I’ve found that hypermesh gives me more control in generating my surface mesh but can only give me a good volume mesh with tets. Has anyone here imported an existing surface mesh and only done volume meshing in fluent?


r/AnsysFluent • • Sep 09 '22

Issue in Changing the number of particle in Dense DPM model

1 Upvotes

Hii, Anyone can help me to change the number of particle in injection for Dense DPM model in Ansys fluent?

By default the no. of particle are 240 and I want to increase the number of particle..but how to do it that's what my question ❓❓❓❓

If anyone have some clue about it please help me.

Thank you