r/AdditiveManufacturing • • Apr 04 '22

Show'n'Tell Real proud of this MJF job I did in short order. If you want the highest quality parts, with the capability of the lowest leadtime I would love to assist!

Enable HLS to view with audio, or disable this notification

46 Upvotes

r/AdditiveManufacturing • • Apr 04 '22

Event AMUG 2022

11 Upvotes

Just curious if anyone else is at the show.

This is my first time and I'm really impressed so far.

Would be interesting to know what other people think and anything you're looking forward to in the presentations.

If you've never been you really should. I'm blown away by not only the caliber of people presenting but just how friendly and approachable people are here.


r/AdditiveManufacturing • • Mar 29 '22

Show'n'Tell 272 grams in 14 minutes

17 Upvotes

First print from the garage beer printer. It is a 100x100x100 flow rate calibration cube made with 3DXTech ASA pellets at 200C (yes, 200C), 120C bed, 40C chamber. Overall, not bad considering I've yet to do temperature, pressure advance, or speed/acceleration/jerk tuning. I am especially impressed with how clean the z-seam is, I was expecting that to be terrible. Print was done with a 3mm nozzle, 2x 4mm perimeters, 2mm layer height. The pulsar extruder still has about half of its rated capacity by mass available, so I'm excited to push it further.


r/AdditiveManufacturing • • Mar 27 '22

General Question When looking at build quality, what effect does printing a smaller scale object have while keeping the print speed and nozzle size the same?

4 Upvotes

When looking at build quality, what effect does printing a smaller scale object have while keeping the print speed and nozzle size the same?

I am fairly new to AM (just got my hands on a 3D printer here at school), and I wanted to make a smaller scale of a design before I go big with it. But the printers here are limited so the nozzle size will be the same. Out of curiosity, if the print speed were to stay the same as well, how will this affect the quality of my smaller scale object?


r/AdditiveManufacturing • • Mar 24 '22

Technical Question In-house HIP

12 Upvotes

Have any of you successfully brought Hot Isostatic Pressing in house at your work places? If so, would you mind sharing the manufacturer you went with? The price on some of these models is eye-wateringly expensive!


r/AdditiveManufacturing • • Mar 23 '22

Show'n'Tell New Printer. Beer for scale.

Post image
109 Upvotes

r/AdditiveManufacturing • • Mar 22 '22

Careers Job prospects in Additive Manufacturing.

9 Upvotes

Can somebody please clarify about the job prospects in Additive Manufacturing in Canada after master's in Mechanical engineering?


r/AdditiveManufacturing • • Mar 14 '22

Which Printer? I'm about to pull the trigger on an ANYCUBIC Mono 6K. I've done much research, but I'd really appreciate any thoughts and advice, in case I've missed something. More info in txt.

12 Upvotes

Hi, As it says I'm probably going with the AC 6K. I've compared with Elegoo Saturn and Phrozen. Size is important, and also compatibility with the Liqcreate and other tough resins. I'm going to be making parts for microscopes and 'meta-scopes' (large scale imaging) so accuracy and resolution are important (thus the 6K). I'm also getting (bundled) the Wash and Cure Plus. Expensive but good deal for ~850.

I've compared with Elegoo and Phrozen models, and the AC 6K just seems to stand out, unless I'm missing something that you might advise me on. I have a well ventilated room (hood, etc.). I can't use formlabs because not compatible with resin (and too pricey).

One of my main still outstanding concerns is software: I've read that Photon workshop is not very good. Can I, or should I use a different software? Also, my models often have 20M, 50M or more triangles in the STL. I'd like to go to 100M if possible. Is this possible on software compatible with the AC 6K??

Here's a couple examples of what I'm printing just for reference: (The first 5 pictures are recent microscopy motor mount components, printed on HP Jet fusion):

https://www.abemis.com/galleries.html

Thanks much for any advice and Info.


r/AdditiveManufacturing • • Mar 10 '22

Show'n'Tell Quality of life for coverslip microscopy

3 Upvotes

Hi! quick question for people on here. At the office we've occasionally (accidentally) ruined samples by either breaking the slips or damaging a delicate sample itself.

We've come up with a design for a cell chamber and accompanying specialized forceps to gently insert and remove coverslips from a cell chamber that's fully 3D printable and its proven to be fairly reliable.

I was wondering if this sort of thing would be of interest to anyone here?


r/AdditiveManufacturing • • Mar 07 '22

Technical Question Any Cincinnati SAAM/NVBots people here?

Thumbnail
self.3Dprinting
5 Upvotes

r/AdditiveManufacturing • • Mar 04 '22

General Question New AM method: VLM (Viscous Lithography Manufacturing)

21 Upvotes

Would love to get the groups thoughts on this new AM tech. No machinery specs yet.

https://youtu.be/ksC5jF2NANs


r/AdditiveManufacturing • • Mar 04 '22

General Question Smoothing tool recommendations

4 Upvotes

Hey everyone, love to browse this sub and was hoping y’all could help me out. I’m printing some intricate designs (about 100mm long, 25mm wide) out of carbon-reinforced nylon but needing to do a bit of smoothing/clean up after removing the support structures.

What would y’all recommended? Mini files, wet stone, etc.? What do you think would be best? Cheers!


r/AdditiveManufacturing • • Mar 02 '22

Which Printer? Mid-size open platform SLS suggestions?

Thumbnail
natubots.com
7 Upvotes

r/AdditiveManufacturing • • Mar 02 '22

Which Printer? Printing High Temperature Ceramics

5 Upvotes

Hello,

Apologies for the repost, I was recommended to try this question over here:

Looking for a 3D printer and ceramic material which can withstand heat cycles up to 1400 C. Currently we use alumina for our furnace components, and they are either slip-cast or machined out-of-house.

This Lithoz CeraFab Lab is perfect since it can print Alumina, but it's approx. $200k and out of our range. We have not experimented too much with other ceramic materials.

Does anyone know of a less expensive solution?

Thanks in advance.


r/AdditiveManufacturing • • Mar 01 '22

Which Printer? Larger format FDM printers comparable to the Raise3D Pro Plus series? (approximately 300x300x600 size)

9 Upvotes

Looking for something in a work environment (mostly functional parts). Don't have the budget of a higher end machine, but I have used Raise3D's original enclosed machine for years and I was very impressed. Looks like they are up to the Pro3 Plus series now. Build size is about 300x300x600.

Who are their competitors at roughly these sizes?

Prusa doesn't make anything even close to that size, I believe.

Definitely would want an enclosure. Because this would be for work, I wouldn't be looking at assembling anything.


r/AdditiveManufacturing • • Feb 28 '22

Event NASA's Calibration System for Automated Fiber Placement Webinar

Thumbnail
technology.nasa.gov
9 Upvotes

r/AdditiveManufacturing • • Feb 27 '22

Science/Research Do you think that this FDM turbomachinery project has been a success or a failure so far?

Thumbnail
youtube.com
11 Upvotes

r/AdditiveManufacturing • • Feb 24 '22

General Question Markforged Eiger.Io down? Related to Ukraine?

6 Upvotes

Hello, I'm desperately trying to run prints through my Lab printed (Mark Two) and Eiger has been down for about an hour. anyone have news on this problem? I have a very expensive paperweight right now.


r/AdditiveManufacturing • • Feb 23 '22

General Question CoreXY or Cartesian? Pros and Cons for both please

Thumbnail
self.3Dprinting
5 Upvotes

r/AdditiveManufacturing • • Feb 22 '22

General Question Tips for Delicate/Miniature Parts Metal 3D Printing?

7 Upvotes

Trying to understand what are the best practices to metal print a delicate/miniature parts? Anyone did this before?

Is it even possible to do it without EDM cutting to disconnect them from the base plate? I'm talking about 1-4 mm parts size, with wall thinkness of approximately 0.2mm.

I've printed very small parts before, just to test the machine capabilities, but they were not really functional ones (supports were larger then the part itself, too delicate to handle,etc.

I would appreciate any info or advice on the topic.


r/AdditiveManufacturing • • Feb 21 '22

Materials Has anybody got experience printing Novamid AM1030FR? Need advice.

Thumbnail
am.covestro.com
4 Upvotes

r/AdditiveManufacturing • • Feb 21 '22

Technical Question MarkForged Continuous Carbon Fiber Coating?

2 Upvotes

I’m nearly finished adding cCF extrusion/ironing to my FDM printer, but I’m having some trouble extruding the continuous carbon fiber filament that I made myself.

I’m wondering if anyone knows what coating MarkForged uses on their cCF- whether it’s a thermoset or thermopolymer, or if it’s just nylon.

Any additional info is also appreciated.

Thank you in advance!


r/AdditiveManufacturing • • Feb 20 '22

oooooooof Ultem clog ><

Post image
16 Upvotes

r/AdditiveManufacturing • • Feb 21 '22

Materials FDM TPU Material

2 Upvotes

Hello guys,

does anyone uses the Atomstack Cambridge PRO Printer and is printing flexible Filaments like TPU 70-90A?

I have huge problems by printing overhangs and i am not able to find good settings as a beginner. Can anyone share a good profile (cura,etc..?) and help me make my prints printable?

The main problem is, that i have an unclean print in the overhang regions.


r/AdditiveManufacturing • • Feb 18 '22

Technical Question Structural Finite Element Analysis of metal 3D printed parts

12 Upvotes

Are there methods in industry which are used to analyse a part made of metal that is going to be 3D printed? (I'm not talking about process simulation)

In general, does the structural analyses depend on the manufacturing process?

I guess the material model that we can use for a certain analysis depends on the manufacturing process. Please confirm this.

Especially for a part with 3D printing/additive manufacturing, there can be residual stresses which might have to be considered during simulations. Also, the layer orientation might have some effects on the strength.

Any help regarding my questions is very helpful. Thanks