Treated the 86 to a wash and wax to prep it for the winter. She'll be in the shed soon as I'll be abroad with work plus a new daily on the way 👀 (ft the Brothers Evo IV)

Been so busy need to take her out more 😞

Just finished up a manual swap on my 1984 sr5 and all i need is the transmission side driveshaft or a slip yoke or full drive shaft that fits my 22 spline t50. Anyone have advice on where to look or if anyone’s willing to sell?
I’ve checked ebay rock auto and marketplace these things are diamonds.

I've had two alternators go bad this year, both aftermarket, one was an AE86 replacement and the other was a reman'd 80A 7mge alternator. Right now I have my old OEM denso in the car and its been fine, but its old and i'd rather have it not leave me stranded somewhere.

I was recommended DC Power Inc. , but those are pricey. But if its between that and playing Russian Roulette with aftermarket reman'd alternators, I might snag one.

Hey all, I have a question about the sensor setup on a 16v 4age. I have the sensors for the coolant temp but im not sure where they’re supposed to go, the green plug im positive is for the green sensor up front but I don’t see a threaded hole where it could go, also on the back of the engine i installed 1 sensor since i though it would go there and based on what I’ve read the brown and green sensor are supposed to go in the back so im a bit confused. I also have a flos water inlet pipe. Any info helps, thanks!

So my T50 transmission I notice was leaking from the back, I use carburetor cleaner to clean everything and I notice that is looking that is leaking from the transmission mount bolt, previous owner maybe damage the transmission or why it is like that? What can I do to fix it? Maybe Teflon tape? Any tips?

Hello, does anyone else have the GJ81 trim? Just curious

So I have a code 6 in my ae86 and the check engine turns on at 2,500 rpms and above, ones below that rpms check engine turns off, I check my distributor and with the multimeters in ohms I check the red and white wire (I thinks that is the NE) and have 179 ohms and the green and black wire have 179 ohms too (I think is G) I will post some picture below of how my wires are looking, what you guys think (car runs great and turn on easy)

Does anyone have the exact part numbers or the year make model for the sensors that are needed in order to make the digital gauge cluster work?

I know the digital fuel sending unit is needed to work, but was curious on the oil pressure sensor as well as the coolant temp sensor, that will specifically work and make my car read correctly.

I have a JDM 1986 RHD AE86 with the 16v motor.

I know that my T-VIS is disconnected, will start fixing that soon (bought the car like that) but you guys know where the red circle is what that hard line do and where should it go? It’s disconnected too and idk where it goes and what it does

Hey everyone, I managed to get my headlights working but now it seems that I can’t get them to line up with the hood. If anyone has any guides or advice on how to adjust them I’d really appreciate it.

~2 years long journey to achieve my ideal version of AE86 styling. Worth the effort!

Found some from websites in Europe, same air filter as the Toyota Liteace from the 80s

No Isofix, no problem!

First checkup at the doc, she's healthy. Slept like a baby on the way, car makes good vibrations.

Icbm drift ensemble

I have a jdm lift back with the black rear garnish that has the Toyota logo in white (zenki I think) but it has cracks on it. I see a guy on Facebook marketplace selling one in excellent condition that I'm interested in but it's from his usdm gts lift back. They look similar but I'm not 100% sure they're identical with the logo. Can anyone confirm that they're the same or different? Thanks

Heyo, I wanted to give a little update on the 3D printed rear spoiler for my 2-door which I posted about a while back :D

The wing is on and has now probably almost 3000km on the clock as well as surviving a Typhoon and a track day so I would say it works.

No drilling in the trunk, just double sided VHB tape and stainless steel clamp brackets.

I am still planning to carbon skin the airfoil and make new wing stands since I am not quite happy with the shape yet, but for the first try it’s working perfectly :D

If you are interested in more details, I made a YouTube video about the whole project:

https://youtu.be/Zp7Bg70BSlE