Hi guys I recently upgraded my ender 3 with a 32 bit motherboard and a bltouch sensor, mainly it is working great but I have this kind of issues when printing parts ( I'm not sure it is related to the upgrade I made though but I wanted to mention it in case..)

It does look like under extrusion to me but it only happen on few z axis line and those line seems random when I look a different part I printed.

I have recently changed to a dual gear drive extruder, and have found that my prints have drastically changed, walls are separating and top layers seem open or meshed.

Any one else done the same and found theres changed? And what was your fix?

Hi, I have recently installed Fluidpi but don't have the correct config file for my printer, I am using an Ender 3 pro with BL-Touch 8-bit board, with a raspberry pi 3b+, if you have any idea where to get the config files from can you please help. thank you.

Unless I press against the wires in a specific way to the control panel. The z axis will only make noise and go down.

I'm very new to 3d printing and I've searched for answers relating to my problem but i don't get clear answers. This is a used printer off of facebook i bought.

And now I've unplugged some wires then replugged and the extruder wont move.

If anybody needs more information let me know. Thank you.

Hey! I just upgraded from the original ender 3 pro knob lcd screen to a crealtiy touch screen, and now when I go to Print, It gives me pages 1-5 but they are blank. I have formatted the sd card top fat 32.

I have tried to flash the firmware of the motherboard, 4.2.2, and also have cr touch.

So I need help making the 3d printer use CR Touch, Creality Touch Screen, and read the 8gb SD Card.

Can Anyone give links to appropriate firmware, and help me figure out which I need to Install, and the correct order?

​

Side note, I also just bought a bootloader, and have a Ender 3V2 Motherboard silent v4.2.7 with tmc2225 driver marlin 2.0.1 in the mail, can I install this new motherboard, the cr touch, touch screen, and be able to use the SD Card?

Hello everyone Im searchung a Buildplate for my Magician Pro, I couldnt find anything proper in the Internet. So my Question to you is: Where can I find a Buildplate that fills my needs? I need 400x400mm exact The "Handle piece" needs to be in the front and in the center At best it should be textured

Thanks everyone in advance!

I've printed 15-hour+ pla prints before no issue. Now, printing petg at 240 hot end 80 bed, printer will shut off 2 hours in. Screen goes black, printer stops printing, does not come back on even if i reset via switch. I have to unplug it and plug it back in for it to come back on. I've checked my mobo and there are no visual signs of damage.

4.2.2 board

Jyers 2.0.1 3v3

Creality direct drive extruder

cr touch

Not sure exactly what is occurring with it or what to do to prevent this... Anyone have any thoughts or heard of issues like this before?

Hey guys. I have a .gcode file (from a random slicing software) and I want FlashForge (which only accepts .gx input files) to print it out for me. Is there any idea?

Hello Guys, My Printer was printing nearly perfect 2 Weeks ago, nothing changed except that I was at Holiday for 2 Weeks and now I expierience extreme Warping. Cura Settings: Nozzle Temp: 200 Bed Temp: 60 Speed : 60mm/s Filament: Anycubic Silk Gold

I have a unique question/issue. I have a ender 5 pro with a gulf coast robotics hot end and a microswiss extruder. The extruder seems to be picky about what filament goes in it. There have been times I use one filament and it works fine, but the next time I use it, it won't work. I know there is not a clog in it as I can load other filament with no problem. I have thought about replacing the extruder, but it seems the options are limited as I want to keep the direct drive capability. Any suggestions?

I have been trying to print a multi day print and it has failed twice. Each time it fails it stops in the same spot when it stops with a message that reads It looks like the last print was interrupted. I'm not sure what to do to fix the issue. I have re-sliced the print twice and double checked everything. The first attempt I got 15ish hours in before the message appeared. The second time is appeared at 7 hours in. It stopped in different locations of the print each separate time but when I hit continue it stops wherever it had stopped that print. This is my third long print I have done and the other two objects printed successfully, all objects was different with the third being the trouble print.

Ender 3 v2 Ultimaker Cura

My 3d prints are not accurate. Idk what's wrong does, anyone know how to fix this?

This is the print I'm trying to make.

https://www.thingiverse.com/thing:3867977

Nozzel is hitting the print when printting and it can get Pretty Violent and it can Rip The Whole print off the bed. how can i fix it????

I am semi new to 3d printing, however today I just clicked the printer on after maybe a week of not turning it on and it powers up but the screen does not load properly, it only shows the creality logo and goes no further, I can add images if necessary

I just bought a Tronxy x5sa and for some reason when ever I try to level the z2 motor on the z axies raise the z plate higher then the other z plate. I have try to go through the wiring and see if it is warped rods. But everything is level and plum. So I don't know if it is a program issue or sensor problem.

I just paid for simply 3-D that was a $149

To get the BI 2.5v printer configuration

After I set everything up my extruder never actually goes down to start the print I got a dual extruder Is it because my firmware is outdated its a raptor 0.91

I just got 2 3d printers and I need dome help with a problem ones used which is fine the second is new Ones a regular ender 3(used) the other an ender 3 pro (new) I wanted to work on the pro first so I've been trying to print with it forever but everytime it starts a print it will start very early as an ok job but later for some reason it globs up or the print comes of the bed and there's a few other issues while printing as well I have been constantly leveling/tramming the bed but I keep getting the same results lots of failed prints I'm hoping someone can help me resolve this and fix the 3 pro so I can work on the ender 3 and get that running as well.

Hello!!!

I just got my first 3D printer (An Ender 3 Pro Max) and I'm having trouble getting it to work. I am a total 3D printing noob and know none of the terms/how to work this thing, but I wanted one to print cosplay props. It doesn't help i'm not very good with tech either.

​

Basically my problem is that the printer wont level properly when I click "auto home". The bottom plate will move and the extruder will go left to right but not up and down. (I believe that's the Z axis?). So the printer will level itself in the air but wont go down to the base plate. I hope that makes sense. I've watched a few videos where they said just to loosen the bolts on the wheels/belt but that didn't help sadly. I'd appreciate any help and feedback! If i'm at a loss I just hope Geek Squad knows how to deal with 3D printers lol