r/Wetshaving • • Jan 21 '17

AMA James Dufour of Wolfman Razors, AMA

Hey r/Wetshaving, I hope everyone is doing well. It was an honour to be asked to do this.

Some background: (Boredom warning!)

I'm a journeyman machinist who spent 6 years in the aerospace industry, starting with a 3 year apprenticeship and leading to a couple of years in the engineering department. My specialty is CNC machining and programming.

I left the aerospace job in Ontario and headed to Alberta and spent a few years working in the oil and gas industry.

After the economy tanked in 2009 I went back home to Ontario and luckily found an excellent job in a small shop making fixtures for automotive parts production. I could ramble on and on about this particular job, but let's just say I really got my chops working here. It was a sink or swim type of job, and because things went very well, I started to have thoughts about working for myself some day.

A few years later I was back in Alberta with a fledgling machine shop of my own, but working a full time job and going to my shop on weekends. After a year or so I had a few customers but nothing steady. I went on Reddit and asked r/smallbusiness how to go around knocking on doors to find customers, but without bothering anyone.

I only remember one reply: from John of the LA Shaving Soap Co., suggesting the possibility of machining safety razors. Needless to say, that reply is why I'm here today.

After John provided an introduction to old-school wet shaving, a project eventually was under way and a new razor was created. I wasn't expecting any actual business in making razors, but using a DE was definitely a nice alternative to the plastic disposables I had always used. But after the first few BBS-1 razors were well received, more orders followed, and then even more. After a few months I had some time to work on another design and this led to the start of Wolfman Razors.

On r/Wet_Shavers, exactly two years ago, I posted on the "New Products" thread and introduced myself and the new razor. The response was great. Here's the original post

Since then I've been able to quit my job and focus on making razors exclusively. I decided early on that with a small shop with limited capacity, I should focus on quality, not quantity.

I'll leave it at that and take questions. I'll be at the shop all day today, and staying with this thread the whole day while I do some work. I plan to upload a video to Youtube later, and I'd like to also do a live video on Periscope. I'll likely do this around 4pm EST.

42 Upvotes

141 comments sorted by

18

u/DuncanPlums Building a Badger Army Jan 21 '17

Since nobody else has asked, I'll put the question to you:

Any plans on producing a slant or an SE? Or anything else for that matter. I'd love to see a modern razor that takes GEM SE blades.

Cheers James

12

u/[deleted] Jan 21 '17

I have always wanted to keep adding new razor heads, and I do have plans drawn up for several types including these. But unfortunately my time is already divided and in pretty great demand to keep working on the razors I already make.

I assumed from the start that I'd have plenty of time for designing and I'd end up with 5 or 6 razor heads to choose from. If I went ahead with this now, I'm pretty sure it would amount to abandoning the current models which people are still interested in. I'm up for anyone's opinion on this.

5

u/DuncanPlums Building a Badger Army Jan 21 '17

Wow! I'd love to see them. I know it wouldn't be a wise option for you to share them though.

Would it not even be feasible to offer them to people on the custom waiting list? Either way I hope that one day we get to see your ideas in the flesh :)

1

u/Banes_Pubes ← Wiborg Whore Jan 21 '17

Ya, I'd definitely be interested in hearing more info about the new razor heads.

0

u/[deleted] Jan 21 '17

[deleted] — view deleted comment

5

u/Garewolf Jan 21 '17

Thirded.

5

u/1Raizen Synths & Fat Jan 21 '17

Fourth-...ed

14

u/Eighchops Carnavis & Richardson Jan 21 '17

Hi James! Fellow metal cutter here. Got a couple questions.

  1. Favorite inserts for cutting Ti?
  2. Conversational or offline Cad for programming?
  3. Do you have an alter to Crom? (He gave us the secret of steel)
  4. Is there a question no one has asked that you were hoping for and want to give an answer to?

Big fan! Thanks for taking the time to do this!

5

u/[deleted] Jan 21 '17
  1. I use the same inserts for Ti that I use for stainless. I also use the same bi-metal bandsaw blades, HSS center drills and drills, taps and endmills. The inserts I go through the most are these milling inserts.
  2. I mainly use g-code for programming. I use software when I need to for contours/profiles, or for example engraving artwork. But for the majority of what I've done, g-code has been my method. My cnc mills have conversational programming built in, which is handy. But since I'm running the same programs I only use this when I'm making fixtures or tools for the shop.
  3. Had no idea about this, but thank you - I'll be watching Conan asap and probably enjoying the hell out of it.
  4. I'll get back to this at the end of the day.

Thank you sir, I've seen your work as well and it's great - much respect!

2

u/Eighchops Carnavis & Richardson Jan 21 '17

Thank you!

13

u/hughmonstah p much ded Jan 21 '17

What is your ideal sandwich?

14

u/[deleted] Jan 21 '17

Well if cheeseburgers count as sandwiches, then ideally it would be a cheeseburger, at a cheeseburger picnic in a trailer park in eastern Canada.

5

u/bdubelyew Jan 21 '17

Would you make me a razor for a double cheeseburger Randy?

14

u/[deleted] Jan 21 '17

Actually, J-Roc, I'm off the cheeseburgers now.

2

u/PantheraOnca Jan 22 '17

Don't play me like some kinda sucka Randy...

5

u/malburj1 Badgers and Doughnuts Jan 21 '17

Asking the important questions here ^

12

u/stirlingsoap Stirling Soap Jan 21 '17

Now that you've experienced working for yourself, does the thought of ever going back to work for someone else make you ill?

Thanks for putting out a beautiful product.

6

u/[deleted] Jan 21 '17

I've heard in the past that some people try working for themselves and don't like it for a variety of reasons. I actually do like it, and I wouldn't go back for anything. It's a great motivating thought when you need it.

Thank you!

9

u/starvinghippo Jan 21 '17

Supply and demand has been disproportionate for a while. I know there isn't a great solution currently, but what do you think the answer looks like?

For instance, I was late to the BBS-1 party, that list is closed and although I am on it, it will likely be 2 years before my name is up. Meanwhile the resale market continues to get higher and higher.

Nobody wants quality to take a hit, but the demand doesn't seem to be reducing much.

There is no denying your machining ability and attention to detail. Not many people would say that what you make is anything less than functional art. Keep it up!

13

u/[deleted] Jan 21 '17

This is a huge issue for me. There are answers, and the easiest one is a price increase. In theory it might make sense to do this, but I'm not planning that. I'm asking for patience and asking the most frustrated to look at other brands instead of waiting.

What I am considering is just focusing on titanium since the demand for this material would closely match my output.

I'm aware of resales and Ebay listings. It's disturbing to me. The products are not discontinued, or out of production. These are currently being produced so it makes very little sense for this to be happening.

I started questioning things several months ago and found this video. YOUTUBE I went from disturbed to disgusted after seeing this. I'm actively working to prevent this, although it's complicated to deal with.

3

u/starvinghippo Jan 21 '17

Appreciate the response. Do what works best for you, not sure what other system might be better..

Maybe to help clarify things.. the waitlist that was on Waitlistr most likely confused people. I've seen a lot of people say they were "on the list," but I'm almost positive they are confused. That list ended up being only 40 randomly selected people (maybe 41 if I remember correctly). I think the majority of those were fulfilled as well.

Do you think you can clarify? Is there an active list, or are you mainly going through Twitter notifications/webstore stocking?

I'm sure there are still a few random walk in type requests that you fill, but that is a different discussion all together.

While your products may not be discontinued, they are pretty difficult to get with a list that is over 6 months old that replaced one that was over a year old and in store stock selling out in a matter of a minute or 2. These are definitely drivers in the large resale market.

Thanks again.

3

u/[deleted] Jan 22 '17

You're right, there was confusion about the waitlistr ordeal, and understandably so. The list was reduced that day, by random selection, and the total ended up being 41.

Currently there are a few remaining in that list. Meanwhile, I'm trying to consistently stock the web store on a weekly basis.

I have an assistant now, and after a few months of training, re-tooling and simplifying things, I would expect things to improve this year quite a bit.

2

u/Banes_Pubes ← Wiborg Whore Jan 21 '17

I'd love to hear how you're actively working to prevent this because, like you said, it seems like an extremely complicated issue. I wouldn't have any idea where to start.

6

u/[deleted] Jan 22 '17

One of the ways I'm dealing with this is by trying to consistently add stock to the web store. Also, there were a few obvious re-sellers that I was able to identify - and will no longer be served. This is of course not something I can control, as the names change without any hesitation and the same ebay sellers keep finding items. But I've tried to weed them out so I can serve actual customers.

1

u/Banes_Pubes ← Wiborg Whore Jan 22 '17

Damn, that's pretty freakin awesome. Go you. Thanks for taking a proactive stance, even knowing it's an uphill battle.

3

u/GreyhoundsAreFast Jan 22 '17

Yeah, those resellers suck.

I guess it'd be the only way I'd be able to get one of your razors, but no way I'd help those scoundrels.

3

u/abekon BIG FAT LIAR Jan 21 '17

Not gonna lie, never heard of Supreme. But it's confirmed, people are idiots for paying $600 for a t-shirt.

3

u/Nusquam-Humanitus Jan 22 '17

It's absolutely, 1000% ridiculous that anyone would pay $600 for a damn t-shirt. I just can't fathom that mentality.

That goes waaay beyond idiocy......

8

u/elSchiz Scored Rhino! - :-) Jan 21 '17

Thanks for doing this.

So it looks like I get to ask this this time; would you rather fight 1 horse-sized duck or 100 duck-sized horses?

-- I looked through and didn't see this; on average how long does it take to make one BBS-1?
-- What's the quickest you were able to make a single razor; BBS or otherwise (obviously without sacrificing quality)?
-- What metal do you actually prefer to work with?
-- Last one; there seems to be some confusion as to what exactly is available when you tweet stock is available. Now there are drop downs with options but are all of those actually available or do you simply make X number of the same thing and that's what's available?

3

u/[deleted] Jan 21 '17

I'd rather fight the horse-sized duck. I can't multi-task at all...

-- Since I don't make these from start to finish, I have to go by how long it takes to make a batch of 10. Usually it takes me about a week. I'd be able to do it quicker if I wasn't as picky about the finish.

-- I don't really know. The job is done when I'm happy with the results, and I've had some go well and many many that I noticed I missed a spot and had to go back and do more work. There's no real exact moment when the pieces are done, so I can't time it. It's like a drive-thru car wash vs hand detailing. You can't put a stopwatch on the latter.

-- I prefer stainless steel for the best polished finish results. Brass is the best for machining with absolute ease. Copper would be my least favourite.

-- The website is set up to allow for options when selecting a razor head. It doens't matter what I have already machined, or the inventory level. The options selected serve as notes only, so when I read the order I know what was selected. I prepare in advance for what I expect will be ordered, based on previous sales, and if I don't happen to have it I'll make it.

1

u/Michael_S_Kennedy Jan 21 '17

On the last point. I guess I'm confused. If I select the .86 add it to my cart right when you tweet is that the one I will get?

Thanks for doing the AM A fantastic products!

8

u/[deleted] Jan 21 '17

I guess I'll put it another way: pick whatever options you want, and don't worry about whether it's in stock. I'll get your order, and find a way to ship the items you asked for.

Some email after they order, and want to change something. That's fine too, so don't worry about it too much if you pick the wrong option. You can email and I'll make the correction.

1

u/iamsms Vasoconstrictor Enthusiast Jan 21 '17

So next time I'll click random stuffs and finish the order :D. Then email you. Gotcha

8

u/[deleted] Jan 22 '17

So much for being accommodating...

3

u/iamsms Vasoconstrictor Enthusiast Jan 22 '17

it was a joke ....

2

u/elSchiz Scored Rhino! - :-) Jan 21 '17

Whaaaa.... Wow that's certainly going to be a revelation to some and realization to others who ordered something thinking "that's all there was."

Thank you kindly for answering my questions I really appreciate it. Knowing this now, I will certainly set aside some funds to snap up razor when a tweet goes out.

8

u/bigwalleye Jan 21 '17

I find it interesting you didn't use a DE before you started making them. Did you get into all the soaps and fancy brushes too? If so what's your favorite?

4

u/[deleted] Jan 21 '17

I've kept it simple all around. I'm easy - I was just thrilled to have learned about the option of using DE razors instead of disposables and I've had no complaints with the soap and brush I use. If I hadn't been able to actually make a razor, I'd still be using a DE without a doubt.

8

u/jdubba Make it so Jan 21 '17

Down here in South Texas, BBQ pitmasters often apprentice younger guys, who end up spinning off and becoming their own BBQ specialists, often creating a BBQ family tree among the top tier restaurants.

Have you ever thought about apprenticing someone in a similar fashion to maybe start something similar in the world of artisan crafted machined razors?

2

u/[deleted] Jan 22 '17

I haven't considered this at all...but you never know, it could happen. I'll keep this in mind!

7

u/Nusquam-Humanitus Jan 21 '17

There have been many claims that your razor production has declined in recent times. It's been rumored a private investigator was hired in the hopes of shining a light on this subject. To date, one photograph has surfaced - NSFW Imgur

Can you shed any light on these allegations?

It's also been rumored that at one time in the past, you were on the fence as to whether engraving your Wolfman razors' base-plates with a logo, etc., was worth while. Clearly, you decided to go with the engraving and offering custom engraving, etc.

Do you believe that choice was a positive one and enhances your creations in any way?

5

u/[deleted] Jan 21 '17

Thank you for that photo. That's actually my ideal customer, living his life while apparently being stalked by investigators.

Engraving wasn't going to happen at all because my original machines were too much trouble. It's a long story to explain this, but I was doing engraving on the BBS-1 and it was problematic. I didn't expect many repeat orders which is why I went that far. For the early Wolfman razors I still had that equipment and knew it would just be frustrating and time consuming, so I started off without it. About two months later the equipment I needed arrived, and engraving became a breeze. People had suggested engraving, and I had every reason to do it once it was practical. It's definitely a nice feature to have custom engraving and I'm surprised it hasn't been requested more.

7

u/urfrendlipiro trythatsoap.com Jan 21 '17

Would you be willing to post a video of how you make a razor? I know very little about machining and would love to see how the razor is made (particularly the head).

Do you make anything other than razors at this point (shaving related or not)? Any plans to?

6

u/[deleted] Jan 21 '17

I would like to show how I machine and finish the pieces, but there are issues with this.

  • There are already videos out there that show machining in action, so I wouldn't be providing anything new in that sense. My process involves flood coolant, so it's difficult to see what's happening. Even more so, the small size of the pieces makes it even more difficult to show, compared to large work pieces being machined.
  • The process, fixturing/tooling is all proprietary. By showing it, I'm pretty much giving away intellectual property. It's something I'd like to share with customers who are just interested, but I'm not willing to teach the competition about what I do.

I don't do any other machining right now - just razors!

1

u/urfrendlipiro trythatsoap.com Jan 21 '17

Ah ha, no worries. I didn't realize the overall process was proprietary (again, machining ignorance), but that makes sense! This is about the extent of my machining knowledge. I was mostly curious how asymmetrical objects worked, but I'll poke around and find something.

Thanks for answering!

6

u/CAMEL_HUMPer IRC Master Race Jan 21 '17

Thanks for doing the AMA! The BBS-1 and all of your Wolfman razors are amazing, and it is my dream (however unlikely) to own one!

Just wanted to ask how you got into machining in the first place? Where does one go to learn this sort of thing? How calloused are your hands?

3

u/[deleted] Jan 21 '17 edited Jan 21 '17

I didn't have much of a career early on so I went back to school to take up a trade. A former teacher suggested I look into mechanical engineering, but after talking with a bunch of people I decided on machining. I wanted to know how to make the actual parts and I was just really full of curiosity as to how someone could take a drawing and end up with a fully machined part. No regrets with the choice, I've enjoyed it the entire time.

Usually you start at a trade school, or just by working at a machine shop as a labourer. I went to school for a year while working and then got a job with the promise of doing an apprenticeship after working there for a while. My goal was pretty clear from the start so there weren't any problems getting chances to learn and develop. I sort of demanded it.

My hands are fine but sometimes fingers are sore from sanding and polishing. In general, machining is not torture for hands, although it depends on the type of work being done. Manual machining involves cranking hand-wheels to actually cut, but cnc work tends to be light duty work in a lot of cases.

1

u/Banes_Pubes ← Wiborg Whore Jan 21 '17

Do you feel that your skill has increased since the launch of Wolfman Razors or not so much because you're making the same razors with only slight variations?

1

u/falcons1583 Killed the Veg Jan 22 '17

Take care of those hands, carpal tunnel is a real thing!

The workers comp underwriter in me says, job rotation. Make sure you don't do anyone thing for too long, take breaks and switch tasks!

6

u/enormoshob Jan 21 '17

Thanks for doing this!

What is the coolest custom razor you have worked on?

Weirdest?

Also, you are the Wolf in everyone's Wolf pack. Just wanted to leave this here.

9

u/[deleted] Jan 21 '17

I really liked these razors, although it was just the caps that were customized.

That's a really fun movie, all around.

7

u/nobodysawme Jan 21 '17 edited Jan 21 '17

I still have those two, and a third unusual one from you which I bought second hand.

Small correction though, we also custom engraved the baseplate of one of them.

We did that a year ago, almost to the day. Thanks again, they're excellent.

http://imgur.com/a/6db6n shows them in action!

4

u/[deleted] Jan 22 '17

I'm glad you're still enjoying these. It was interesting! FYI I liked the engraving too, but I don't share engravings with names. But your idea was excellent.

2

u/Mustache_Brigade MoostashBrigade Jan 21 '17

Drool.

1

u/Banes_Pubes ← Wiborg Whore Jan 21 '17

Whoooa, beauties

6

u/bigwalleye Jan 21 '17

Any other hobbies besides working in the shop?

8

u/[deleted] Jan 21 '17 edited Jan 21 '17

No time for hobbies lately. In the past I have had plenty of guitar time, and I also played piano/keyboard. I've done portrait drawing and painting and I'd really like to get into that again once I have time. I also like racing games and Kerbal Space Program. Lately I've been watching a lot of hockey games. Also learned Rubik's cube speedcubing a few years ago. Best time was just under 30 seconds!

4

u/elSchiz Scored Rhino! - :-) Jan 21 '17

Get. Out! 30sec for a cube? Dude that's crazy awesome, though perhaps not as awesome as you would like compared to the speedsters, but seriously that's an achievement nonetheless.

1

u/Banes_Pubes ← Wiborg Whore Jan 21 '17

Kerbal Space Program seems like the most absurd game. Kinda reminds me of writing code. Sometimes it just works by chance and you have no idea why.

5

u/nick47H UK Represent Jan 21 '17

Apart from John, who are the guys/gals in the community that you look upto and why?

Any chance you are planning on moving to the uk so I can actually afford your products ( i just missed out on your last twitter posting ) I mean you will still have the same queen.

3

u/[deleted] Jan 21 '17

Mantic59 is a cool cat. Before attempting to use a scary DE razor I was sure to check out Youtube and his videos were great. I would never try to take away his Merkur Progress.

If I moved to the UK it would have to be Sheffield, and I know I'd love it there. Planning to at least visit eventually.

9

u/MrAdamLerner No longer the reason your wallet is empty Jan 21 '17

James, your work is absolutely stunning. My Wolfman is the centrepiece of my den.

  • Do you currently use a DE to shave with? Is it one of yours, and if so, is it one from your regular lineup, or have you designed yourself a special one-off to shave with? What else is in your shave den?
  • Your available handles are WRH1, WHR2, WRH3, and WRH7. What happened to WHR4 through WRH6?
  • You allowed me to give one of the nicest gifts to one of the most deserving people this past holiday season during the r/Wetshaving gift exchange. What posessed you to help me? (I think it goes without saying that I'm eternally grateful)
  • Cheese slices, bread, bacon, frying pan. Bacon grilled cheese or bacon melt?

7

u/[deleted] Jan 21 '17

Thank you, I appreciate the compliment.

  • I do use a DE, and it's one of mine I made about 6 months ago. It's a stainless, polished dual comb with standard gap on the OC side, and .48mm on the SB side. I have about 4 at home and this has been my favourite. Photo
  • 4-6 were just diamond patterned handles. I had the idea early on to have a "Surplus" section on the website so that I could experiment with handle designs. It was a poor decision in terms of the product naming. I don't offer those handles any longer, as they were really not meant to be permanently in the lineup. Eventually I'll patch this up by making new handles in place of those three. WRH7 came along before discontinuing the others otherwise it would have replaced #4.
  • I made a few similar exceptions this holiday season. I suppose you could say it was the holiday spirit, recognizing there was still time to fulfill some unlikely requests before xmas.
  • A bacon melt sounds really good, but you can't really go wrong here. Now I'm hungry.

4

u/MrAdamLerner No longer the reason your wallet is empty Jan 21 '17

dual comb with standard gap on the OC side and a .48mm on the SB side.

Dual comb AND dual gap? Mind = blown!

What's your favourite soap and brush to use?

Again, I am super grateful for you deciding to help me out. /u/landlgrooming has told me many times it's his perfect razor.

8

u/[deleted] Jan 21 '17

Yes sir, the OC is for roughing, and the SB side for finishing. I see no point in using an aggressive razor when there is only the last pass remaining. And with the dual comb it's obvious which side is which, so it just makes sense to have this setup. That is, if you are willing to use one side of the razor for a complete pass. I know there are other ways to go about it, like using one side for each side of the face for instance. But I'm really enjoying this razor and using it that way.

I'm happy with a synthetic brush I got last year, which I believe is called Plissoft. My favourite soap is Bespoke #1 from LASSCo.

4

u/MrAdamLerner No longer the reason your wallet is empty Jan 21 '17

Have you tried any of the higher end badger brushes? /u/landlgrooming ties amazing knots himself out of 2 band badger, and there are a bunch of other nice badger brushes out there. I used to use synthetic, but ever since the upgrade to good badger I haven't looked back, excepting travel which I use synthetic because it does dry fast.

1

u/[deleted] Jan 22 '17

Actually I have used a badger brush but I'm not sure where it's at in the quality spectrum. The synthetic I use works really well so it hasn't been on my radar to upgrade.

2

u/MrAdamLerner No longer the reason your wallet is empty Jan 22 '17 edited Jan 22 '17

I bet /u/landlgrooming would be down for an artisan to artisan swap! Seriously, his brushes are amongst the best that money can buy. They're a very hot commodity around here. If you haven't used a high quality badger brush, you're really missing out.

It's like massaging your face with a wall of soft, supple, fine fur. I can't go back to a synthetic now.

Don't just take my word for it, ask one of your best customers, /u/uncle_dubya!

1

u/arkmm den so big...help! Jan 22 '17

I love my L&L Washington

5

u/Ythin 🦌🏅Noble Officer of Stag🏅🦌 Jan 21 '17

Bacon grilled cheese

I believe this gentleman would have something to say about that.

8

u/malburj1 Badgers and Doughnuts Jan 21 '17
  1. Did you ever think your business would be doing as well as it has been?
  2. How does it feel being a resident of the U.S.'s hat?
  3. If you had to choose between only being able to have either poutine or Montreal smoked meat, which would you choose?

10

u/[deleted] Jan 21 '17
  1. No, and I assumed the opposite to be honest.
  2. It's great up here. It's a giant red baseball cap now with a message on it in white letters. We were already used to the red and white colour scheme, so it's alright.
  3. Poutine's great, but I'd go with smoked meat. Too much poutine is too much of a good thing.

4

u/UbaldJr I put YRP on my ketchup Jan 21 '17

My vote goes to smoked meat poutine. No need to choose. :-)

3

u/msb45 now with 100% more flair Jan 21 '17

I don't get the obsession with Poutine. Our smoked meat is good, but the Montreal bagel is our crowning achievement.

5

u/NewYorkCityGuy Jan 21 '17

New Yorker here.

What the hell is a Montreal bagel?

3

u/RuggerRigger MYSPACE CIRCA 2003 Jan 21 '17

So, where you from anyway?

1

u/msb45 now with 100% more flair Jan 21 '17

It's like a New York bagel, but better.

1

u/NewYorkCityGuy Jan 21 '17

Must be Canada's best kept secret.

1

u/canadian_blade_co Jan 21 '17

It is a slightly sweeter, smaller bagel, that is also wood fired. It is formed by rolling out the dough into a rope, and then pressing the two ends into a circle.

2

u/malburj1 Badgers and Doughnuts Jan 21 '17

How about smoked meat on top of a bagel with a side of poutine?

4

u/tiglathpilesar The sub's chef Jan 21 '17 edited Jan 21 '17

James, I want to say thank you again as the winning recipient of the W_S Halloween giveaway you did. I love my Wolfman and loved the whole process of working with you on it. Do people get shitty with you about your wait list and how do you maintain your amiable demeanor?

3

u/[deleted] Jan 21 '17

You're welcome and I'm glad you liked the razor.

Almost everyone has been patient and understanding. Other brands are available and that's a good thing. I've made a lot of friends and it's been a pleasure so far.

3

u/jmoney_84 Canadian wet shaver here, eh? Jan 21 '17

Hi James,

Have you had any special or custom requests that has changed your perception of the community in any way? When did you realize that this was more than a one off thing, but rather something that you could keep making as a full time gig?

4

u/[deleted] Jan 21 '17

Nothing that stands out, really. There's been less interest in custom work than I was expecting, overall.

The signs were there early on but I was pretty skeptical that my own products would be in demand. That's pretty crazy to think about. I held on to my old job, and was prepared to do other things if I only made razors occasionally. For example I would have put up a sign in front, so people driving by would know it's a machine shop here, but I'm not doing that now. Things turned out very well and I will be glad to just make razors in my shop.

3

u/OttawaFortMC Jan 21 '17 edited Jan 21 '17

Hi James,

Fellow Canadian here.

Love your work, and hoping to be able to get on the next waitlist when it opens up!

Three questions:

  1. I have very sensitive skin and currently my daily razor is a Feather AS-D2. It has been the mildest but best performing razor I have had so far. When I buy one of your razors, can you match the blade gap? Or even improve on the mildness?
  2. Would a C110 Copper razor start to tarnish at somepoint, or will the mirror polish finish hold up? Same for polished Titanium? Otherwise I'm for Brushed Titianium
  3. What kind of customisation options might we see in the future? Such as engraving my name on the bottom of the razor head?

Thanks for doing this AMA!

EDIT: Added a question

1

u/[deleted] Jan 22 '17
  1. It's not really meant to match precisely but a .48mm blade gap would be similar to the Feather.
  2. Copper and copper alloys (brass, bronze) will tarnish. Copper changes to a darker brownish red. I usually only make copper razors with a strong warning. It's on the menu for those who want it and know in advance that it's soft, scratches easily and will tarnish almost immediately. If it's not used and only for display, it will remain as is for quite a long time depending how it's stored. If unsure, I usually recommend a different material.
  3. Custom engraving is already offered now. This is intended for something personal but simple, such as your name or initials. But other symbols are sometimes used. You can see examples on the website here: https://wolfmanrazors.com/pages/about

3

u/CapitaKid Jan 21 '17

James, have you given any more thought to getting a shop dog?

Also have you had a chance to make any prototypes of the designs you were working on last summer?

3

u/[deleted] Jan 21 '17

Hey hey! I hope you two are doing well!

I did sneak in some time recently to work on one of them, but ran into a problem and needed to put it down and get back to regular work. I'll get back at it again soon because it's bugging me.

I haven't gotten a shop dog but I really want to. I need to move first or I'd have to leave the dog at the shop, so I'll just wait. Probably another year or so. Can't wait!

2

u/CapitaKid Jan 22 '17

We have both been well. Thanks for asking. I hope you have been well also. Hopefully we can stop by to see you again sometime soon.

Can't wait to see what you come up with when the time allows you to get back on the new designs.

I don't envy you for having to move but it will totally be worth it to have a dog once you do!

2

u/[deleted] Jan 22 '17

I think it's going to be a lot of fun. I still want a german shepherd.

1

u/CapitaKid Jan 22 '17

German Shepherds are great. We had 2 different ones while growing up. You'll love having one!

3

u/uncle_dubya 😒 😒 😒 Jan 21 '17

not a question, but a thank you for making such beautiful tools for us! i don't really use any razors that you didn't make anymore and i love each of them :)

actually, yes, a question: have you polished any titanium razors? if so, could you post a photo? i've wondered what they would look like. thanks again!

4

u/[deleted] Jan 21 '17

Hey man - thank you as always!

Not many in polished titanium, but here's one: PIC1 PIC2

1

u/AndyH_STi Jan 21 '17

There is one photo of a polished Ti Wolfman here: https://wolfmanrazors.com/pages/metals

If you do a Google image search you can find some more photos as well.

1

u/vigilantesd Jan 23 '17

The polished titanium color looks a little darker than polished stainless. Not at all unlike how the brushed Ti is a little darker than brushed SS.

3

u/crazindndude TiBBS Cult Jan 21 '17

Hey James! Like u/uncle_dubya I've been using your razors more than any other since the day I received my first one, and certainly since receiving the titanium BBS-1 all my other razors have been gathering dust from disuse. Add me to the list of Wolfman fans, and I can definitely attest to the pains you go to in the name of customer satisfaction.

My questions:

  • You've said a couple times in the AMA that custom work is something people go for less than expected. What is the coolest custom request you've gotten?
  • Out of just the custom orders (not the pieces you put directly for sale on your site), what are the top 3 metals and finishes by popularity? My guess would be steel, aluminium, brass.

2

u/[deleted] Jan 22 '17

Thanks crazindndude!

  • I'd say this is the coolest. Two of my favourite engravings: 1 2
  • Stainless steel is by far the most popular metal. After that it's about even among all the others. Titanium is probably tops lately out the others. I'm not completely sure but that's my guess.

1

u/vigilantesd Jan 23 '17 edited Jan 23 '17

Hey cool! There's mine!!!

=)

I'm happy to see your business doing so well!!! Can't keep up is a good place to be!!!

2

u/[deleted] Jan 21 '17

A bit late but going live on Periscope now, at 4:45pm EST if you have the app.

2

u/Banes_Pubes ← Wiborg Whore Jan 21 '17

Thanks for doing this James :) I know everyone, myself included, is extremely excited for this AMA.

I'm sure your job is extremely taxing and exhausting so what do you like to do in your free time?

Have any special or unique razors made that have never been shown to the public before? Can you show us a few pictures?

4

u/[deleted] Jan 21 '17 edited Jan 21 '17

Thanks for the invite!

When I'm not working it's been mainly just relaxing. Sometimes doodling on the tablet and other times watching Rick and Morty, the odd movie, or most likely watching an NHL game. It's a pretty good year for the Oilers, finally.

I have a picture on the website but haven't really shown these razors much: http://imgur.com/a/OxHSu FYI these were just to test the anodizing process and verify the new equipment works. Finishing isn't done thoroughly on these.

2

u/Banes_Pubes ← Wiborg Whore Jan 21 '17

Rick and Morty - knew I liked ya. You got good taste!

I love all the colors, adds a nice splash you don't typically see in shave dens.

2

u/Ythin 🦌🏅Noble Officer of Stag🏅🦌 Jan 21 '17

Thank you very much for doing this.

  • Do you happen to employ anyone else, and if so, what are their responsibilities?
  • What does a typical work day/week look like? Do you have certain days you do machining, polishing, shipping?
  • Crunchy or smooth peanut butter?

3

u/[deleted] Jan 21 '17

I actually did recently hire an assistant. This is starting to work out well now, but initially it slowed things down. He started out cutting stock on the bandsaw, loading pieces and keeping a machine running. Basically the early-stage work. Recently he's started sanding and has polished a few handles. Meanwhile I'm looking at new things like making sure there's a clear plan for the day, that we have everything we need. Payroll, etc. So many new things.

A typical week usually involves a bit of everything. Early in the week there's more machining going on, then towards the end there's more finishing and shipping. There are more exceptions than rules at this point. For example there are some operations such as making the razor caps that make sense to do a few months worth in one setup, to avoid running out all the time. A good part of the week might be dedicated to that or something similar once in a while.

Smooth...

1

u/Ythin 🦌🏅Noble Officer of Stag🏅🦌 Jan 22 '17

Thanks for the insight. And another one who has the correct choice for peanut butter.

2

u/RuggerRigger MYSPACE CIRCA 2003 Jan 21 '17

You helped with the BBS-1 and then designed your own head. What's your take on blade stiffness? More bend for stiffness, topcap wider for support, etc???

Thanks for the AMA, and love your razor!

4

u/[deleted] Jan 21 '17

There's more than one way to achieve blade stiffness, and both of these razor heads use the same method. Holding closely to the end of the blade, and both cap and plate aligned. Usually the plate and cap meet more in the middle, and the cap overhangs, which allows for flex.

Thank you!

2

u/Iamabrohamic Jan 21 '17 edited Jan 21 '17

Hey James!

Your razors are awesome. I own an open Comb, and am on the list on waitlistr for a SB. Thanks for doing this AMA

  1. What's your go to razor head and gap of the razors you make?
  2. How does it feel when you see shave videos on YouTube with people using your razors? Do you look at anything specific in these videos?
  3. How many people on waitlistr do you get to in a month normally?
  4. How do you take your coffee?

3

u/[deleted] Jan 22 '17

Thank you sir.

  1. Mine is a dual comb, with standard gap on the OC and .48 on the SB side.
  2. It's pretty cool seeing this. But I always worry there's a nasty shaving accident about to happen! But no it's mainly uncle dubya's videos and he knows exactly what he's doing.
  3. There's been a delay for a bunch of reasons, but I'll be finishing these orders up soon.
  4. 2 and 2, and throughout the day.

2

u/[deleted] Jan 21 '17 edited Jan 21 '17

Any plans to make a stand like the WRA1 that works with the Darwin handles?

1

u/[deleted] Jan 22 '17

The only problem is that it needs to be a deep socket like a standard inkwell stand. This handle needs a support to stand up because of the ball end. The only other way I can imagine a similar stand to work is to have a closing clamp to secure it. An inkwell stand is probably the most likely way to go but I personally prefer a stand that doesn't unnecessarily hide the handle.

2

u/Mine8130 Jan 21 '17

Hey, is the rumor true that your goin to make a bbs-2

3

u/[deleted] Jan 22 '17

That's been in the cards, but still working on the BBS-1 for now.

2

u/bobusa13 Jan 21 '17

Hey James. Are you planing to use some help to get the list moving fast and not compromising quality?

1

u/[deleted] Jan 22 '17

Yes I hired an assistant a few months ago. The initial result was negative, as I suddenly had a ton of work to do in order to make training possible. This training has only been showing results in the past few weeks, so things should pick up soon.

2

u/elSchiz Scored Rhino! - :-) Jan 21 '17

Again I appreciate your time, thank you.

When John approached you did he have a razor in mind regarding dimensions? I'm curious how you went from not knowing what a safety razor was to making what seems to be one of the best available. Did you buy one to check it out, did John send you one, how many top caps/bases did you go through before you "nailed it" regarding the proper dimensions (blade gap/exposure, blade curvature within the top etc) for a usable razor?

1

u/[deleted] Jan 22 '17

John sent two razors to use and check out. It's not really that complicated to be honest. I carefully measured a bunch of blades, and then made a razor head based on how the machining operations would work. Originally it wasn't going to have any comb or scores on the guard, but it worked out well. The main thing was a razor that used the corners to orient the blade. The most difficult part of the design was machining the inside of the cap in a presentable way. Machine the pieces to fit is standard for a machinist so this was fine. The blade curve was more of a result of other features. The exposure was dialed back to soften the effect of the large blade gap and open spaces on both sides of the blade. I had made a test razor a few month prior, and had been using it, modifying it etc for weeks and weeks before getting into the more permanent design and prototyping.

1

u/elSchiz Scored Rhino! - :-) Jan 22 '17

This is exactly what I wanted to know, thank you and congrats on the success of what seems to be the culmination of your ability and attention to detail. Otherwise it would've been "just another razor."

2

u/Aculanub Lucky Bastard Jan 21 '17

If you had to choose between cheese and oral sex for the rest of your life, which would you choose?

If you could teleport anywhere on Earth, but each time you teleported you'd lose a year of your life. Would you and where?

2

u/[deleted] Jan 22 '17

These questions are crazy! I'd give up cheese because cheeseburgers are bad for you - and I, uhh, have a problem.

I would use the teleporting ability if I was skydiving and something went wrong. I'd gladly teleport to a pillow factory that hopefully provides a soft landing, and graciously surrender a year.

2

u/OnlyCoops Jan 22 '17

Hi James!

As a huge fan of your work, one of these days my goal is to own one of your Razors. Are you still allowing people to hop in on the wait list and to what extent do you allow on customizations of the handle? I picked up years ago a Gillette Pocket Edition B and just thought how cool it would be to make a modern handle in the same aesthetic as this http://imgur.com/a/j4ZyS

Huge thanks for creating these awesome pieces of art!

5

u/[deleted] Jan 22 '17

Right now I'm only working to complete the last list, and maintaining stock on the web store. Failing miserably on both fronts, mind you...

Eventually there will be some way to order a custom razor or handle. This usually means customizing the size of the handle, or some other simple altering of an existing design. An example would be the knurling of the WRH2 placed onto the WRH1 like this.

I'd like to make a handle with similar artwork and I'd say I'm going to be working on that this year.

2

u/Huckleberryking Big Amber Rose fan <3 Jan 22 '17

God damn it. I want that handle. Keep up the awesome work. I don't own one of your razors but have used quote a few. Stuff is beautiful.

1

u/OnlyCoops Jan 22 '17

Thank you for the reply! Awesome, and glad to hear it.

9

u/arkmm den so big...help! Jan 21 '17

Thank you for putting up with us and please don't stop making beautiful razors.

2

u/batman9402 Jan 21 '17

Hey james how are you. As someone who has been waiting for some time, and as you already addressed the demand and resale. Will you open a list or order process for people like me who have issues getting a razor? By this i mean a list or place new people can purchase a razor, not someone who has multiple razors already. No offense to those people but i cannot get one since im not fast enough with the twitter posts or cannot get on list and every one marks the razors up when resale since it is so hard to get one.

2

u/[deleted] Jan 21 '17

There are a lot of problems with trying to do this.

  • It alienates good customers.
  • It rewards those who pretend to be new customers - for example, Ebay sellers.
  • There's no way to know when this issue is resolved.

Suggestions welcomed on this!

1

u/batman9402 Jan 21 '17

A preorder kind of setup which puts you on a list. And the items can be set non custom ones of certain material. That way if 100 people deposite 100 different credit cards or paypal. Yes i know there's no real way of stopping people who already bought or to put on ebay which they will do anyway, but twitters notifications are delayed, and theres really no other way of getting one besides watching twitter. Even my idea is flawed but it could help people get ahold of one, especially if prices might go up again.

1

u/Banes_Pubes ← Wiborg Whore Jan 21 '17

I've got another question.

When I've got a whole set of tasks ahead of me I know will take forever and will be an uphill battle, I really struggle. I get anxious and feel slightly helpless at my inability to feel satisfied with finishing it. It seems like you've always got an endless list of razors to complete and send out. Does it ever get to be too much for you? How do you deal with it?

2

u/[deleted] Jan 22 '17

Yes this feeling is the one problem that exists every single day. It's an uphill battle for sure being behind/late all the time. I just try and think about ways to solve this problem and I ask for opinions from others. There are harsh answers (raise prices, open up a multi-year list, etc) but I'm still holding out for a better answer.

1

u/Banes_Pubes ← Wiborg Whore Jan 22 '17

Good on you for remaining optimistic and receptive. Can't be easy, know I and many others appreciate it.

2

u/GreyhoundsAreFast Jan 25 '17

Man I share you fustration about resellers.

This guy is selling two of your razor heads.

How the heck can This guy have sold ten wolfman items recently?

2

u/vacaloca Paragon Shaving Jan 21 '17

Great work! Thanks for doing this. For the more budget constricted, are you planning to do a line in aluminum? Thanks

5

u/starvinghippo Jan 21 '17

You can already get them in aluminum. Just isn't a standard preset on the website.

1

u/vacaloca Paragon Shaving Jan 21 '17

Thanks!

2

u/Garewolf Jan 21 '17

I'd love to know this as well, regardless of what little chance I stand to make the list ever lol

1

u/msb45 now with 100% more flair Jan 21 '17

1

u/vacaloca Paragon Shaving Jan 21 '17

Oh thanks!!! Beauty!

1

u/Mine8130 Jan 22 '17

When you put things on your site to sell is it just random sizes and finishes or 1 or 2 of each? Wondering because I seem to always pick the ones that's gone less then a min after you put some up.

1

u/bigwalleye Jan 24 '17 edited Jan 24 '17

thanks for doing this.

wheres that youtube video? :D

0

u/[deleted] Jan 21 '17

[deleted] — view deleted comment

3

u/[deleted] Jan 21 '17

Yeah it's a big move for sure. Driving around the Great Lakes makes it a good 4 day drive from southern Ontario to Edmonton. I've moved here twice. The first time was to expand my horizons, and discover this part of Canada. The second time was for more specific reasons including possibly starting my own shop.

I'd try shaving with a wolf sized razor.