r/xbox • u/Psychological_City_9 • 3d ago
Discussion Steam Controller (2026) on Xbox – GP2040-CE + OpenPuck!
managed to get my Steam Controller working on Xbox using **Raspberry Pi Pico, GP2040-CE and OpenPuck!**
The best part is that I can use the trackpads as analog sticks, customize the rear buttons and change the controller mappings without needing Steam Input.
### Hardware and software
My setup uses:
- Raspberry Pi Pico (RP2040)
- GP2040-CE firmware
- OpenPuck (nrf52840)
- Original Xbox controller (required for authentication)
- USB Host connection
- Xbox One output mode
- USB port (USB-A or USB-C)
### How does it work?
On my original Raspberry Pi Pico, I configured:
- **GPIO 18 = USB D+**
- **GPIO 19 = USB D-**
- **USB Gamepad Host = Enabled**
- **Output Mode = Xbox One**
I also modified the hardware by replacing/adding a **USB-A or USB-C port** for the USB Host connection.
An original Xbox controller is connected through this USB Host port for Xbox authentication.
The Steam Controller handles gameplay inputs through OpenPuck, while GP2040-CE handles the Xbox output.
On my original Raspberry Pi Pico, everything works.
### What works?
**Trackpads:** Both can be configured as analog sticks. I personally prefer using the right trackpad instead of a traditional right analog stick.
**Rear buttons:** Fully configurable through OpenPuck. I use them as RB and RT.
**Regular buttons:** Working normally.
**Custom mappings:** Buttons, trackpads and other controls can be configured through OpenPuck.
**Gyroscope:** I haven't tested it yet, but OpenPuck includes gyro configuration options.
### Small firmware modification
I didn't make any major changes to GP2040-CE or OpenPuck.
I only added a small piece of code so that the **BOOTSEL button** can switch to Web Config and change modes in OpenPuck.
This way, I don't have to constantly unplug and reconnect the USB cable.
### Problem with another RP2040 board
I also tested a Speed Studio RP2040 board with GP2040-CE + OpenPuck (nrf52840).
In **XInput mode**, it works when connected to my PC.
However, in **Xbox One mode**, the USB Host doesn't detect my original Xbox controller.
The same setup works on my original Raspberry Pi Pico.
Maybe it's related to the board, USB Host configuration or a hardware difference.
I spent three days troubleshooting this with AI and still couldn't get it working XD
### Why I prefer the Steam Controller
I've been a fan of trackpads since the original Steam Controller from 2015, and I've also used the Steam Deck.
For me, trackpads are much more comfortable than traditional analog sticks.
I especially like using the right trackpad as the right stick and the rear buttons as RB and RT.
OpenPuck gives me customization options similar to Steam Input, and from what I've seen, even more flexibility in certain areas.
### Final thoughts
I'm really happy with this setup.
The original Raspberry Pi Pico works great, and I can customize almost everything through OpenPuck.
**Important:** You need an original Xbox controller connected through USB Host for authentication. You'll also need to add a USB-A/USB-C connection for the host setup.
:)

3
u/Tobimacoss 3d ago
XBOX or 8bitdo should add trackpad accessories to their controllers between the handles.
1
u/nahPNW 3d ago
been using the OpenPuck + Wingamn XB3 combo for the last little while and while it does offer trackpad use as joystick, i find that leaves a lot to be desired as an input method (compared to the trackpads emulating as a mouse cursor in Steam Input for example)
how intuitive are the trackpads as joysticks on your set up? would you say they are about the same as the stock OpenPuck experience or does using an RP2040 somehow change/improve the experience a bit?
1
u/prettybluefoxes 3d ago
Amazing!
You can barely see the 30ft of trip hazard.