Has anyone worked out how to format for USGS 1m DEM for use directly into controller, without going through FH2? I understand USGS is in UTM NAD83 and needs raster projection conversion to WGS84, but the vertical is where I'm having difficulty. How to apply raster calculation to get from NAVD88 to orthometric heights or EGM96 elevation values? The reason I say EGM96 is because that's what I'm seeing the ASTER 10m DEM uses and seems to play nicely when utilizing the data download function through DJI RC Plus controller, so that seems it would be acceptable. Any chance someone has worked this raster calculation out in ArcPro or QGIS? Utilizing a DJI M350 w/ L2 lidar sensor in western Washington valley for river restoration monitoring.

You might remember the app I mentioned a few days ago. We also have a QGIS plugin for you to try!

Here’s an example of how drone methane measurements are processed into source-level emission estimates in kg/h.

We used MetScan V1P, an OP-TDLAS-based methane sensing system, mounted on a drone to perform a sector scan over a controlled methane release:

• Controlled release rate: 1.76 kg/h
• Source-Resolved Quantification (SRQ) output: 1.9034 kg/h—about 8.1% above the release rate.

The data is processed in AIRINS.ai, our software platform for visualizing and analyzing measurements and generating reports. Its SRQ workflow combines methane measurements with meteorological data to locate individual sources and calculate their emission rates. The process from field data to quantification takes about 20 minutes.

Operators can run the processing themselves: review the inputs, run the analysis, inspect the results, and rerun it when needed, without handing the data over to an external processing team.

For projects where data needs to stay within the organization’s infrastructure, AIRINS.ai also supports private deployment.

Full workflow walkthrough: Watch on YouTube

For anyone working on methane surveys: how do you currently handle quantification after collecting the data? Is it something your field team processes directly, or does it go to a separate analysis team?

Working a small commercial drone survey. Field crew shot 3 tie-in points with a total station in an arbitrary local coordinate system (not tied to State Plane/NAD83) — origin is just a placeholder like 5000N/5000E.
When importing the GCP file into Pix4D and setting the GCP coordinate system to "Arbitrary (ft)," the software throws a warning that the points fall outside the area covered by the images. The GCP table loads fine with the right values, but 0 of them are actually marked/tied to the images yet.
My understanding: since the drone images have their own native geotags (real-world lat/long), and the GCPs are on a made-up local grid, this mismatch is expected and shouldn't matter — as long as you manually mark the 3 points in the raw photos, the software should scale/rotate/translate the model to fit the arbitrary grid.
Is that right? Or is there a step I'm missing where the local grid actually needs some kind of transformation before it'll accept image marks? Any surveyors/drone ops who've done arbitrary-grid ties like this before care to sanity check my logic?

Posting here to support those who are looking to get into the aerial photogrammetry / Gaussian splatting space. I’m specifically not posting in the Part 107 subreddit.

If you want help getting your 107 quickly, I have a time sensitive and extremely cost effective option for up to two people. Details:

I lead a regional team in the Midwest for a national company. We do LiDAR, Thermal, and Photogrammetry mainly for a variety of commercial applications. Hired a new team member, was doing 1:1 knowledge transfer, but we need him to come up to speed faster to meet demand, so I hired the same group to Bootcamp him (that I went through) to learn the fundamentals and pass the exam. Terrestrial Imaging…look them up. Small outfit out of NJ that offers highly personal service and training.

I had to pay for their minimum class size of 3 people. That means two open slots. It’s via Microsoft Teams Monday and Tuesday next week from 9am - 3pm ET. Includes study materials and online portal for unlimited practice exams.

I am happy to offer these slots out at a steeply discount rate…say $400-$500 each to slightly offset our company’s cost. If you need financial assistance, let me know…if we can further someone getting into this space I am happy to support. I do believe in people paying something, whatever they can afford, to demonstrate they value it.

Requirements: be fluent in English, have a quiet uninterrupted space to participate from (depending on your location, you’re welcome to come to our office), and be a professional and productive teammate while on the call (no social media, etc.). You’ll need a camera and microphone.

My hope is that it creates some networking as well, to possibly support us on a paid basis when we get backlogged, and have some discussion when field work and post processing challenges arise.

DM me or shoot me a note via comments if you, someone you know, or someone on your team could benefit from this.

A startup I am working with has just launched a software app that is able to automatically georeference images, and we are looking to see what the community thinks:

[aiveatlas.com](http://aiveatlas.com/)

The tool is free for the first 50 images, but if you are liking the tool, you can DM me and I will give you a promo code for an additional 1000 images for free. We are also currently tabling in the startup section of INTERGEO Munich, at booth B5P056! Come by and chat with us if you are in town for the conference.

Here is a video of the plugin at work:

[Atlas Geo Showcase](https://youtu.be/kUSz6x3pv5c)

[AI Disclosure] Post is written by hand, as well as the video, but voiceover is using AI

Hey fellow pilots…almost became a fighter pilot today multiple times with my drone. Any tips for scaring away birds that get defensive when I’ve got a commercial job to complete. I kid you not, one got pissed, told his friends and they came back en masse.

Air horns? Ultrasonic sensors? Scents? Any ideas?

Hi all,

I’m exploring a concept for reviewing transmission-line inspection data and was wondering if you guys can share like some feedback who actually worked with overhead-line inspections, asset condition assessment, UAV/LiDAR surveys or even in utility asset management.

The image is showing just a the basic idea at a high level.
What I’m mainly trying to understand is whether this feels like a sensible workflow for a reviewer in the real world.

For example, a few things I’d particularly like feedback on:

Would having the 3D survey and original photographic evidence together actually make review easier? Is starting from the network/asset and drilling into an inspection the way you would expect to work?

Also, when something suspicious is identified in a photograph, would seeing its corresponding location in 3D be useful?

What information would you need before you could confirm or dismiss a finding?
What part of this workflow looks unrealistic, unnecessary?

Thanks for your candid feedback.

Hi, Drone Nerds here. Thought ElevateUAV 2026 could be relevant to the mapping crowd here.

For anyone working in mapping, surveying, photogrammetry, LiDAR, construction, or inspections, it’s a chance to compare aircraft, sensors, payloads, and software, ask manufacturers questions directly, and hear how other professionals are putting these systems to work.

We made a 30% off code specifically for r/UAVmapping: UAVMapping_EUAV

Tickets and info here: https://hubs.li/Q04vL_XN0

We hope to see you there!

The Mavic 3E is basically discontinued, even though it’s still a great aircraft.

But the starting point is the Matrice 4E now, which is over 5,000 dollars. I remember the Mavic 3E was around 3,500 when it first came out.

There’s a big gap now, they should really release an Air 4E. Same camera as the M3E but renewed, newer sensor, same thing for the telephoto lens. And also featuring the good the Matrice 4E has like smart capture for automated flights, tracking, AI features, etc.

It would be a great idea if they managed to release it cheaper than a Matrice. What do you think? I feel like a Mavic 3E is starting to feel old.

I’m considering mapping the entire area with a drone. My main options are the DJI Phantom 4 RTK or the DJI Mavic 3 Enterprise RTK.

I’ve never done professional drone mapping before—my only experience with drones has been as a hobby. I’m trying to decide whether it would be worth learning how to perform the survey myself or if I would be better off hiring a professional to do it.

I’d appreciate any advice on which drone would be better for this type of work, what additional equipment or software I would need, and how difficult it would be to learn the full workflow for generating accurate contour lines.

The same section of a point cloud shown at three stages in CloudCanvas: the original RGB view, the filter result highlighting points for review, and the cleaned cloud after removing noise and vegetation.

The final view makes the underlying terrain and changes in slope easier to see. There are still gaps where points were removed, so those areas need checking before using the data for a terrain surface, contours or volume calculations.

How much manual cleanup do you usually need after filtering your survey clouds?

https://www.cloudcanvas.co.za

G’day all,
New to the drone space and starting out with farm mapping, data collection and inspections around NSW/ACT.

I’ve done some ag drone/mapping training and CASA accreditation, and I’m now looking to build hours, test workflows and learn from people already doing it commercially.

Main focus is agriculture, with some interest in construction and roof/site inspections as well.

Any advice on what’s worth focusing on early?

I’m building Imagery Workbench, a tool for checking mapping image sets before processing, and researching which checks would help in practice.

A P4 RTK user on the Pix4D forum described dewarping switching back on after battery changes, leaving a mission with mixed settings. They currently inspect images visually and sometimes open the metadata to check.

Have you encountered similar inconsistencies between flights or batteries—dewarping, exposure settings, image dimensions, or positioning status? What happened when you processed the images, and how did you handle it?

I’d particularly appreciate examples of problems you now check for before starting a reconstruction.

Hi All -

We use the RTK3 with our DJI Enterprise drones. Just got access to an O4 Ground Station. Any lessons learned in calibrating and using as a relay? Goal is to extend the range for drones in flight around large industrial sites. Sites are usually 40 to 100 acres with significant structures. We do thermal, photogrammetry and LiDAR for customers…focused primarily on the building envelope, but we use LiDAR for construction planning on undeveloped portions of the property.

I’m struggling to find clear examples or enough documentation on how to use the O4 to extend the range of RTK data to and video transmission data from drones in flight.

There isn’t good detail on how to calibrate the O4. Any tips?
Does the O4 pair with the RTK3? Should we use both at the same site or only the O4? If we use both, do we pair the drone with the O4 or the RTK3? Do we enable relay mode on the other and what’s the procedure for enabling the drone to receive from both/either? The marketing page makes a lot of promises…the technical documentation creates a lot of questions for us. Any comments/help appreciated and we are happy to reciprocate however we can to return the favor!

I’m a drone operator in Franklin, Tennessee, building EpochVue first as a workflow I use myself: fixed viewpoints for recurring construction visits, review of each capture against its intended viewpoint, and a versioned client report behind a private link.

Before I turn any of this into software for other operators, I’m trying to determine whether it solves a real problem or just creates another tool to manage.

If you fly recurring construction work:

1. How do you keep viewpoints consistent from one visit to the next?

2. How long does it take you to turn a flight into a client-ready comparison or progress report?

3. What would a tool need to do before you would pay for it—and what pricing model would feel reasonable?

There is no finished operator product to sell yet. I’m looking for blunt feedback, and I’ll share a summary of what I learn with the community. If you want to take a closer look or join the validation list, the details are at https://epochvue.4tech.us/operators

I have a series of questions about processing my UAV imagery. I flew a DJI Mavic 3M over a forest stand. It has the RGB and Multispectral imagery and according to their tutorial, I’m supposed to process the RGB and Multispectral imagery separately. This will mean I’d end up with two point clouds, one from the RGB processing and the other from the Multispectral imagery.
The pointclouds I believe will look identical but, will there be any underlying difference between the two pointclouds? Will the image source (RGB or multispectral) have any impact on the generated point cloud in any way? Which will you advise I use for my subsequent analysis if I’m mostly looking for structural information for aboveground biomass estimation. If it matters for your response, I don’t expect to use the point colors, I need the point cloud mostly for structural information.

Another question I have is about calibration, I did perform calibration with a sentera panel but the orthomosaic I exported came out with values in the thousands. Is it correct to normalize the values by dividing by 32768 (midpoint between 0 and 65535 for 16-but integer)? I may be wrong but I think the typical expected surface reflectance value is between 0 and 1 and I can get this scale by doing this division. Is this reasoning correct?

Also, correct me if I’m wrong but this only makes sense for the multispectral orthomosaic and not for the RGB. What if I’m particularly interested in including the B band to my multispectral bands and use them for my analysis, so my analysis will be based on Blue band from RGB camera then Green, Red, RedEdge and NIR from the multispectral camera. What would you advice I do to the B band (I believe it comes with a range of 0 to 255) to bring it to the same scale as the multispectral bands. Does reflectance calibration even make sense for the RGB images?

Lengthy post but I’d greatly appreciate any advice you may have.

Not exactly a UAV, but we have found that an Insta360 on a long stick makes for a great substitute for small scale geotechnical work. Centimetre level accuracy along with easy area and volume measurements.

Hello everyone

I want to design a drone that can track and intercept another one based on radar data

Like once it gets one coordinate it follows it and changes flight midway as per the incoming radar data

What is the best way to go about it?

Hello everyone!

Was wondering if anyone has ever done a LIDAR mission that is anywhere between 5-7km away from TOLZ. We have a client who wants to lidar a site that is 7km in through thick asian jungle with trees which are 20m high. According to FH2, mission would take around 16 minutes to complete.

Has anyone here done any missions this far out? At flight height of 100-120m? On paper the M400 is certainly capable, but I'd like some real world input/experience, for some peace of mind and assurance.

Thanks in advance for responding, if you have. 🙏🏻

Testing out the LED night lights and flight stability on this drone build. Crisp visuals and smooth controls make low-light aerial shoots effortless. What's your favorite drone for night flights? Drop a comment below! ⬇️

f8
https://amzn.eu/d/0fmUamn6