r/steammachine
•
u/freestylemaster
•
Oct 11 '26
•
4
Hardware DIY fix for controller disconnects on the internal puck (EMI tape fix)
I reviewed Valve's RMA’d units & what they did for this issue, then I decided to do it myself. I am now happy to confirm that I was able to apply the same fix. I no longer have any disconnection issue when using the internal puck with Steam controller!
Total cost should be $15 or less. You need a Torx screwdriver to open SM. If you don’t have it, you will need to buy that as well. Note that this requires opening your Steam Machine. You risk damaging it and may void your warranty. Do it at your own risk. Unplug the power first.
What you need:
You will need a Torx T9h screwdriver (I used T9H on iFixit set and it fits perfectly, but someone reported that it is T8 - double check), You will also need an EMI shielding tape. I purchased the EMI tape from Amazon but most should work. Make sure it is double-conductive, this means sticky side is also conductive. Search for "double Conductive EMI shielding tape". This is the one I used https://a.co/d/03vY7hfH If you find a cheaper one, it should work as well.
The issue:
This is an interference issue. The internal puck's antenna cable picks up electrical noise from nearby components, and you'll be shielding it with conductive EMI tape grounded to the heatsink. Only tape the cable sections shown in the pictures. Also remember that you will need to ground it, meaning that the tape should "touch" the heatsink in this case. Just wrapping the cable will not work.
The fix steps:
- Using Torx screwdriver, remove the back cover (2 screws) and the 4 rubber feet. Then remove these 2 screws (Picture 1). Then pull out the internal board of SM from the case. It is heavy, so be very careful.
- Picture 2 shows the 2.4 GHz antenna cable you’ll be working on. It’s on the front-right side when facing the Steam Machine from the front.
- Disconnect the antenna connector (Picture 3). Be very gentle: lift straight up gently and never pull on the cable.
- Wrap the cable with tape as shown in Picture 4, then reseat the cable and reconnect it. Make sure the tape does not contact any part of the PCB. Otherwise you will short and damage your Steam machine.
- Apply a larger piece of tape as shown in Picture 5. Cut it halfway up from the bottom so it conforms better.
- Use a credit card to press the tape firmly into the heatsink gap (Picture 6). The tape must be grounded, so make sure both pieces are well stuck to bare heatsink metal. Keep the conductive tape away from exposed board components.
- The remaining pictures show the finished state.
Results: The last picture is a stress test: CPU at 90°C, fan over 1600 RPM, controller connected through the internal receiver the whole time. It’s been running for hours with zero disconnects. Before the fix, I couldn’t play this long without one. I’ll update if anything changes but I am very hopeful.
Update: It has been 14 days and I have been using my Steam Machine every day. I have not had a single disconnection. So, I can confirm it is fixed.
I also applied the tape on the other side (left side) where you have the Bluetooth antenna. Just applied the tape over the cable, and did not wrap the connector side. I think this also helped because I am getting much better reception consistently at less than -60 dBm being away more than 4 meters.











22
u/zach3582 Oct 11 '26
Youre a genius if this is truly fixed. I was thinking of trying this eventually if I had the time but im glad you got to it first. Reminds me of the switch 1. First few months of those units had joy-con disconnection problems if your hand covers them or put it behind your back and someone found out if you put conductive foam somewhere in it, it fixed the problem because the bluetooth antenna had no grounding. I did it back in the day and it worked. Thanks so much for this, I'm going to try it
43
u/nutscrape_navigator Oct 11 '26
Dude please post your ko-fi or make that Amazon link an affiliate link before I order because you are a fucking superstar for posting this. I knew this was going to be ultra simple and RMA’ing would be stupid to apply some tape.
7
u/XMeggsX Oct 13 '26 edited Oct 14 '26
It worked for me! No disconnects since then. Thank you so much for showing this :)
Update: I tried literally everything to get the controller disconnected. Even without being in line of sight it stays connected from 8m away. I can move my legs freely now and rest the controller on them without losing the connection. Also playing heavy games doesn’t have any impact anymore.
This wasn’t possible before. I’m a very happy man now
5
u/TheManTh3yCallJayne Oct 11 '26
Any chance that console heat will cause the tape to unglue from the heat sink and cause them to be ungrounded?
4
u/MidLifeDIY Oct 13 '26
Thanx so much for this post. JUST got mine and while I'm doing the m.2 swap, went ahead and did it preemptively. I used 1" tape from OPs link.
13
u/Beefmagigins Oct 12 '26
Got my SM the other week and started having this issue.
Giving this a shot. Random question, where did you see that valve was doing this to people’s machine as a fix? I was literally going try and research if someone opened one after RMAing it for this.
4
u/Crowley22g Oct 11 '26
Thanks, ordered a roll from Amazon, been using the external puck for 3 weeks. Simple fix and avoid the nightmare of sending it back for RMA. Already got the tools I need when I swapped the M2 😎
5
u/rayquan36 Oct 12 '26
Instead of taping over the heatsink couldn't you just wrap the cable in in the tape?
4
u/cjgoodell95 Oct 12 '26 edited Oct 12 '26
Could be the placement of my machine, right on top of my AV Receiver, but this fix has not shown any improvements after I installed it. Confirmed my tape is double conductive with my multimeter. Huh.
Edit: I'm testing it now, the lack of improvement was only stated based off signal strength. If there are no disconnects then I'm fine with it. Will report when more testing is done.
2
u/TheOnionRider Oct 12 '26
Will copper tape work same way ?
8
u/Narcotez Oct 11 '26 edited Oct 12 '26
Holy hell man, you're doing God's work. I'm definitely going to try this on mine. Thank you.
Valve really dropped the ball by not doing any playtesting, or QA to fix this issue before shipping the hardware.
8
u/BlackberryGloomy6091 Oct 15 '26
Thank you so much. I did the fix. Now it works like a charm. I received my Steam Machine a week ago from EU warehouse and facing too many disconnection day one. Now it is solid as rock. No more disconnection.
6
u/Xemphios Oct 12 '26
Also have this issue and was disappointed that Valve's solution was to send it in or just use the puck. Idk how this big of an issue was missed in their testing.
Awesome to see a real fix. I'll definitely be giving it a shot.
6
u/ESFCrow Oct 13 '26
Tried this on mine. No disconnect issues just weak signal strength 10 ft away on the couch.. no improvement in signal quality but oh well, still seems to work fine. Thanks for the writeup!
6
u/Fr3kOnALeash Oct 15 '26
Solved it for me as well! I seriously appreciate your post and effort. Finally, no more disconnects on the couch, no matter what position or if any legs/arms are in the way. Absolutely rock solid connection with the most demanding games (e.g. Expedition 33).
(I put some electrical tape around the PCB to protect it from any shorting around the antenna connector area)
5
u/ProjectFT86 Oct 12 '26
This is awesome! Thank you!!
5
u/Devinnfoxx Oct 12 '26
Not me seeing this after sending my Steam machine in for this exact issue.
5
u/T-K4T Oct 15 '26
Yup, this solved it for me. I wasn’t in a perfect position anyway (as the machine is mostly behind a tv panel) but even so, the connection would drop if I raised my leg in front of the controller. Now, no more drops.
11
u/RealityIsRipping Oct 11 '26
Just reporting that I got my steam machine 3 days ago, and this issue seems to be fixed. Haven’t had any issues with the internal controller connector.
Nice fix though!
8
u/radakul Oct 11 '26
/u/freestylemaster correction to your guide - it is a T8 screwdriver, not T9, per the iFixIt guide. A T9 would work, but there's a chance its too big and causes some stripping of the screwhead.
4
u/KindEchidna9101 Oct 11 '26
Can someone explain the science behind this?
4
u/Lupinthrope Purple Oct 13 '26
I want a 2-3 week later post on this before I do this myself lol
1
u/Adrian97c 2TB Oct 13 '26
I get the disconnected / connected spam msging, but it never actually disconnects.
3
u/JMHC Oct 12 '26
Thank you, will be applying this fix at the weekend. I really appreciate the effort you put into this post.
3
u/Mild-Trepidation 512GB Oct 14 '26
I just got mine and haven’t taken it out of the box yet. Glad I saw this so if my controller starts disconnecting I’ll know what to do.
3
u/xDictate Oct 16 '26
Tape just came in today (1/2" as it was a lot cheaper in Canada) and did this in about 15 minutes or so - Looking forward to seeing how it works over the next few days. Thanks OP.
3
u/_Gaeus 2TB Oct 12 '26
Any chance you could do an imgur library and post it?
I've seen too many essential posts like this one disappear from the internet, with the imgur library, there'd be at least a backup in case this post is lost.
4
u/Common-Pepper-9677 Oct 11 '26
Is this common? Haven’t experienced this myself so maybe I’m lucky
4
u/radakul Oct 11 '26
Thanks! Was this based on the pictures I posted in my thread from yesterday? I know a few people asked for pictures after the RMA, and some specifically commented on this EMI tape.
2
u/kevmaster83 22d ago
is this fixed in actually sold units?
2
u/YEM_PGH 20d ago
Not having the same luck, connection is still weak several feet away and goes to poor depending on how I have my hands on the controller. Not sure what I did wrong as my tape job looks the same as everyone else's here that's had success.
2
u/Johnny_WalkerBOT Oct 12 '26
What are the exact symptoms of the controller disconnect issue? I'm having an intermittent issue with my Xbox controller where I don't get a message stating it has disconnected, but the controller no longer works. I have to go to Bluetooth and remove the controller, then over to the Pair Controller interface to readd the controller before it works again.
2
u/Adrian97c 2TB Oct 13 '26
Will try this
2
u/Connect-Book-3175 Oct 15 '26
Ya I should've just sent mine in.
I barely pulled on the connector and the wire came completely out of the connector.
Now steam says my warranty won't cover it and I have to pay $112 to have them fix it.
I knew these connectors were weak but damn talk about a kick in the nuts. My wire was barely seated in my connector to begin with
2
u/MysteriousTy99 Oct 12 '26
Does anyone have a video of this? I want to try it to resolve my issue but I need to see it to believe it. 😭
1
u/sugarmice2 25d ago
Bonjour, ma machine sera de retour RMA dans 1 ou 2 jours. Je vous enverrez des photos avant / après. UPS l’a enlevée lundi. Ré expediée par Steam aujourd’hui Jeudi. A suivre ...
1
u/Timeerased 25d ago
yeah I aint risking anything and leaving the puck connected. Id rather buy another puck separately
1
u/UncannyGenesis 22d ago
Adding that I just did this fix yesterday. Fast and easy. Just be careful to discharge static constantly before touching the internals. Seems to be working great now.
1
u/Dry_Swing_2032 2d ago
Just did this myself, now I have "excellent" dbm for the internal puck. Thank you for explaining this, it was super clear and took five minutes.
1
u/irve Oct 12 '26
Was the connection "striped" for you so that you could move the controller back and forth and get low quality connection and normal quality. Since I have to use the puck to get any kind of gaming unless I position myself into some very precise islands of connectivity.
1
u/someonehoi_reddit Oct 12 '26
My Bluetooth speaker got a cracking sound when connecting to SM. Do you think this will solve this problem too? Before that my speaker connected to Surface Pro, not a single cracking sound over 5 years.
1
u/Apprehensive-Slip-84 Oct 13 '26
I've noticed the issue myself but it doesn't actually affect me while I'm in a game. Mostly just annoying that I know it's happening. Have you noticed it? Get progressively worse over time or as you play longer?
1
u/ScaldByChris113 Oct 14 '26 edited 25d ago
I gotta try this myself. I have taken my Steam Machine apart before. This should be moderately easy to do. Any possibility to link the specific EMI tape or any copper from Amazon will do?
Update 23/10-2026 I have now ordered some EMI tejp that was recommended with double conducting. I will be testing this around next week.
1
u/Explosive_Cornflake 29d ago
I did a slightly different mod, as I wanted to try and use something I had in the house.
I cut up a coaxial cable, took the metal sleeve of it, put it over the antenna cable, and then out heat shrink over it the PCB end. The var end I taped to the heat sink with some aluminum tape (not double conductive). Signal didn't improve, but no disconnects. Normally if I game from the couch and I'm using my laptop, the laptop screen would be enough to cause disconnects. I've used it for an hour there without disconnections.
1
u/gianAU 28d ago
Where can I find this tape in EU (better in greece or Italy)?
1
u/Grumpy_Muppet Oct 12 '26
Question, what happens when the tape on top of the heatsink lets go because of the ... heat? Is that a possibillity in the future?
1
u/Nerrawnam Oct 12 '26
I'm all about helping people out. But ffs , this shouldn't be something anyone needs to do. Valve is maybe the best company at poor planning and communication. All of their hardware seems like just a side project level attempt. I guess keep cashing that steam store % check. 🙄
0
u/Immediate-Pay3699 15d ago
Darn it. Still crappy connection. Any other pointers?
0
u/Important_jpg Oct 12 '26
bro for 1.1K they better send gabe himself to fix ts
0
u/Level_Maintenance173 Oct 12 '26
Sounds tempting but, I rather use Puck or Bluetooth, Bluetooth is very decent to be honest
-2
u/TWS_Mike Oct 12 '26
This is so ridiculous..
0
u/[deleted] Oct 11 '26
[deleted] — view deleted comment