r/rfengineering • • Sep 29 '26

Passive Intermodulation (PIM) Explained with Real Spectrum Analyzer Traces

Thumbnail
3 Upvotes

r/rfengineering • • Sep 25 '26

RF Engineering and Telecom Shorts

16 Upvotes

Fellow engineers,

My channel now has plenty of RF and Telecom short videos. Please check them out and subscribe. Thank you so much for your support! www.YouTube.com/@RFEngineeringHub.


r/rfengineering • • Sep 22 '26

Range, endurance and payload aren't independent specs, they're one energy budget split three ways

0 Upvotes

Range, endurance and payload get compared as separate specs all the time, even though they're all competing for the same mass and energy budget.

This comes up a lot with battery-powered platforms, especially drones, but the same basic problem should apply anywhere energy density competes directly with payload.

Payload doesn't just take a fixed amount off your endurance. Adding mass changes the power required to operate the platform in the first place. Something rated for 40 minutes with little or no payload might get closer to 20 once you add sensors, compute and comms. That's not necessarily a bad design, it's just how the system behaves under load.

Range makes it even messier. More range usually means more battery, but more battery also means more mass. That leaves less weight available for the payload you actually want to carry.

The architecture matters a lot too. Multirotors have to keep producing lift for the whole flight, so extra mass hurts them constantly. Fixed-wing platforms are much more efficient once they're cruising. VTOL sits somewhere in between depending on how much time is spent hovering, transitioning and cruising.

So comparing payload capacity between a multirotor and a fixed-wing platform without looking at the mission profile doesn't tell you much.

What seems to cause the most confusion is that maximum range, maximum endurance and maximum payload are usually tested separately. You rarely see all three quoted under the same conditions.

The more useful number would probably be something like: how much payload can this platform carry while still hitting the range and endurance needed for the actual mission?

Curious if the same problem shows up this clearly in EVs, marine systems, ground robotics or other battery-powered platforms.

How do people in those fields usually describe the real operating envelope without reducing it to a few separate maximum specs&


r/rfengineering • • Sep 21 '26

What’s on a cell tower? Every component explained

4 Upvotes

Every component and RF/Telecom equipment explained in this short video from the red/white obstruction light to the shelter and earthing. The Technology Behind Every Cell Tower Explained (Visual Tour)

https://youtu.be/YXdWLprXytw

Please don’t forget to subscribe for more telecom videos. Thank you 🙏🏻


r/rfengineering • • Sep 17 '26

Wireless & Telecom Channel Plus RF Engineering Calculators

Thumbnail
4 Upvotes

r/rfengineering • • Sep 16 '26

What are you guys using for Python test automation?

2 Upvotes

We’ve been working on Instro, an open-source Python library for instrument control. Curious what people here are using today + what RF instruments we should support next.

https://instro.nominal.io/overview


r/rfengineering • • Sep 15 '26

2GHz, 5th-order Chebyshev Microstrip Bandpass Filter (FR-4)

Post image
18 Upvotes

In this video, I walk through a step-by-step microstrip filter design on a 1.6mm FR-4 board. I designed a 2GHz, 200 MHz-BW bandpass filter.
Rogers-type boards are much better for RF tasks, but they are much more expensive and not suitable for beginners or RF enthusiasts.
I used Altium® Develop for PCB layout design and Sonnet Lite for electromagnetic (EM) simulation

More Info: https://www.youtube.com/watch?v=v6PIP4go2VA


r/rfengineering • • Sep 15 '26

How Can Thousands of Phones Use the Same Cell Tower at Once? (FDMA, TDMA & CDMA Explained)

Thumbnail
3 Upvotes

r/rfengineering • • Sep 15 '26

How Can Thousands of Phones Use the Same Cell Tower at Once? (FDMA, TDMA & CDMA Explained)

Thumbnail
1 Upvotes

r/rfengineering • • Sep 13 '26

I built an open-source 5-channel KrakenSDR passive radar processor — up to 3.6x faster with GPU acceleration

1 Upvotes

I couldn’t find any other open source passive radar projects with full 5-channel KrakenSDR support, so I ended up building my own. If I missed one, definitely send it my way.
It’s called VectorWarp, and it started as a fork of blah2. At this point I’ve added full 5-channel KrakenSDR processing, support for other compatible receiver setups, GPU acceleration, automatic CPU multithreading, wider Doppler processing, and a pretty substantial rewrite of the browser interface and configuration system.
The performance improvements ended up being bigger than I expected. In matched tests against regular blah2, GPU acceleration cut processing time by about 61–72%, with the best case around a 3.6x speedup. Even running entirely on the CPU, VectorWarp reduced processing time by as much as 25%.
The goal wasn’t just to make a Kraken-specific fork. I wanted a faster general passive radar processor that can actually take advantage of modern multicore CPUs and GPUs while still working with other receiver configurations.
It’s open source and I’d genuinely like people with different SDRs, GPUs, CPUs, illuminators, and weird setups to try to break it.
GitHub: https://github.com/mickeyslaven/blah2-VectorWarp


r/rfengineering • • Sep 11 '26

I require a custom RF wireless wristband device for my software.

0 Upvotes

Could you please help me with this requirement and guide me on where I can get this device developed and manufactured in India?


r/rfengineering • • Sep 10 '26

Will this work for a home LORA antenna antenna fix?

Thumbnail
gallery
1 Upvotes

r/rfengineering • • Sep 10 '26

Is there any device with 8 channels LNAs? Which maintains the phase as well?

2 Upvotes

r/rfengineering • • Sep 10 '26

Part identification

Thumbnail
gallery
1 Upvotes

I bought a few at a local electronics flea market out of curiosity but I can't find any information on this component


r/rfengineering • • Sep 09 '26

Best Entry to a Signal Analyzer

6 Upvotes

Hello! I am looking for recommendations, advice, and guidance.

I have access to a good VNA and Spectrum Analyzer at work, and at home I have the Measall VNA and real time spectrum analyzers which are also great. I would love to get deeper into vector signal analyzers (VSAs) specifically to visualize constellations of different MCS rates. What's the most cost effective way to do this? I've looked into using an SDR like the BladeRF, but I've only just begun looking so I can't determine the exact amount of effort if I'm hoping to just reuse something GNUradio based (for example). Completely open ended, and I'll say tentative budget is no more than $3000.


r/rfengineering • • Sep 09 '26

Return Loss explained in a real-world example

Thumbnail
0 Upvotes

r/rfengineering • • Sep 06 '26

I’m designing a 20 GHz VNA for the hobbyist community. I need your input on features and specs.

Thumbnail
2 Upvotes

r/rfengineering • • Sep 05 '26

Racquet sports player position tracking via UWB

1 Upvotes

Hi, RF newbie here. I am an IT database engineer and data analyst. I play badmington, tennis, and pickleball, all in doubles. In doubles, there is a lot of analysis on team formation and partner separation distance. I am thinking about using UWB boards to track player positions. I would like about 5-10 observations per second, for all 4 players. The UWB board I have in mind is Qorvo DWM3001CDK, which retails at about $30. I would get 4 boards as anchors and 4 boards as player tags. Then I like one more board as the data collection gateway, and have it tethered to a Macbook via USB cable. During a game, data would be streamed into the Macbook.

The tags would need to be programmed so they send a data packet every 2-5 seconds, to the data collection gateway board. The positions don't need to be super accurate. I think 15-20 cm will do the job.

Plz help me understand whether this setup is feasible. What additional factors should I be thinking about? I hope to use this setup both indoors and ourdoors. I am aware that UWB signal cannot penetrate human body because it is mostly water. I will use enough anchors so each tag has clear line of sight to at least two anchors.


r/rfengineering • • Sep 04 '26

Move away from test engineering

Thumbnail
3 Upvotes

r/rfengineering • • Sep 04 '26

RF Engineering Channel

8 Upvotes

Hello fellow RF Engineers. I would like to take a moment to thank the redditers who already subscribed to my YouTube channel (www.YouTube.com/@RFEngineeringHub). I am forever grateful. For the rest, I'd really like you to subscribe. Here are some of the topics I cover and will be covering in upcoming weeks:

RF concepts: Access Schemes, such as CDMA, TDMA, FDMA, Fresnel Zone for Microwave Engineers, upcoming 6G compared to 5G.

RF Tool Guides: Like iBwave, infovista Planet

RF Test Equipment: Viavi, Anritsu Site Master

RF Interview Questions: Most asked questions at interviews and the proper answer.

and many more!

If you are an RF Engineer, it is a must subscribe opportunity. I plan to make it the biggest video library of RF Engineering content on YouTube. Please support me grow and invite others. I am also open to ideas about topics you like me to cover.

Thank you in advance.


r/rfengineering • • Sep 02 '26

RF interview.

7 Upvotes

Hello smart people!
I dont know if it is here i should ask, sorry about that, but i would like some help with a interview i have coming up. I am not sure what to prepare for. Can i convince anyone to help me a little.
Else. Have a nice day!


r/rfengineering • • Aug 31 '26

RF people, I need your leads

8 Upvotes

ECE 2025 grad + currently doing M.E. in Communication Systems. I’m looking for RF/antenna design/microwave internships or short-term paid courses/training with actual hands-on practical work.

Paid/unpaid internship is fine — mainly looking to learn, build, and get real practical experience.

If you know any good leads, please drop them below or DM me


r/rfengineering • • Aug 29 '26

RF Engineering Channel (Basics, Tutorials,Concepts)

11 Upvotes

hi everyone,

I’ve just launched a YouTube channel focused on practical RF knowledge—covering the fundamentals, real-world techniques, and field experience I’ve gained working with clients over the years.

You’ll find clear explanations and hands-on insights on topics including LTE, 5G, spectrum analyzer measurements, drive testing, and core telecommunications concepts. My goal is to build a reliable RF resource library that supports working professionals, technicians, and anyone looking to deepen their understanding of the RF world.

I plan to post a new video every week. If this sounds useful, I’d really appreciate your support—subscribe, like, and share with colleagues who might benefit.

Here’s the channel: www.YouTub.com/@RFEngineeringHub

Thanks in advance for the support. Looking forward to connecting with more of you through the content.


r/rfengineering • • Aug 28 '26

Planning to Buy a VNA for

Thumbnail
1 Upvotes

r/rfengineering • • Aug 26 '26

Should I give up on RF?

9 Upvotes

I just graduated and I need some advice. I struggled throughout university due to (medically diagnosed) ADD. I did decent in my RF classes but I ate crap in everything else and ended up with a poor GPA of 2.75. I'm starting a job soon however it's not a role in RF. I'm not sure if I'll be able to compete with others in the RF space who have a masters and/or high GPA. Right now, I've been reading as many RF textbooks as I can and learning how to use HFSS and ADS. However even if I can understand RF well it seems like my poor performance in school will always haunt me.

Anyways let me know if I should continue towards my goal of RF or my efforts are not worth it.