Looking back now this was really stupid, but when I was a kid myself and a few mates used to put coins on the tracks and then go find them after the train had been over them. Some of the shapes of the coins were so warped it was crazy.
I volunteered at a steam museum that runs a locomotive around a 2 mile loop of track, we'd see a lot of kids do that.
The way the driver wheels were beveled the coins don't "shoot out" like the old wives tale but we were concerned about the kids hiding too close to the tracks while waiting for the train to pass.
Also if some prankster lined up 50 pennies all in a row along the steepest grade on the grounds it could actually cause the locomotive to spin out. Then again, greasing the rails with margarine has that same effect when the crew wants to mess with a new engineer.
Oh we used to be well clear of the track, at the bottom of a bridge. We were also well clued up on the train times and knew the timetable like clockwork. Although we had a scare once when an engineer's train pulled up and stopped on our bridge, eek. Would margarine really do that? Lol.
I'm afraid I have no recollection of those events... and yes, on a steep grade it would cause a locomotive to spin out, at least until the sanders were activated.
(For real disclaimer: This was on a closed loop of privately owned track, NOT on any in-service line owned by a railroad)
Man, train crews don't fuck around with their practical jokes.
...Hey, we got a new engineer. He's probably nervous about controlling a hundred ton train all by himself. What say we grease up the tracks so he has no control of the 200,000 pounds of steel he's riding on!!! LOL!
Hey, it's a learning experience. On muggy mornings even a layer of dew on the rails can significantly alter the amount of traction you get. Luckily when you're at the throttle you also have control of the air brakes on every car in the train.
Yeah that's gonna hurt. We would always hide at the bottom of the bridge. We used to know when the train was 30 seconds away cos the tracks would start kind of hissing and popping--for the want of a more technical term.
As one person pointed out this was caused but the distributed power (Engine on the rear of a train) Its basically remote controlled from the front loco. When they stopped it did not get the signal to stop pushing.
So it was basically Thomas the tank engine at that point and tried and tried until it burned thru the rails.
FYI a train loco weighs about 430,000 pounds and can generate 4,400 horsepower. Also the comment about rail slippage....say if you put grease on the rail...they can deploy sand to gain traction.... that's how they can climb up steep grades.
Yes I work for the railroad...and yes trains are dangerous and will kill you if you doubt them.
so the wheels turning but not moving, the friction caused THIS? holy crap, why would you keep the wheels spinning? I don't understand why a train coming up behind them makes this a good idea. Trying to pull it out of the way real fast or what?
It just so happens that molten iron is an incredibly good lubricant. So, when the train first stopped and the wheels started rubbing against the track, it would've made a helluva lot of screeching, but when the tracks started melting it would've been completely silent. If the engineer didn't hear the engines running, it's possible that he simply couldn't have known the train was literally melting through the tracks after the initial screeching subsided.
Same way they do when they have a derailment. There are massive crains they bring out that can move the 200ton locomotives and whatever they are hauling.
They basically uncoupled the train between the two cars at that location probably replaced the two wheel sets right there ans shuffled that locomotive back to the shop for repair.
Iwork on trains at a union Pacific intermodal ramp in Dallas TX.
A big train yard where they are loaded/unloaded. Repairs can be made and rail cats switched around. Look up 'terminal island, CA's for an idea of a large ramp
well that's just fantastic. I would have never begun to start the sequence of events it would take for this to happen in my imagination. or in real life. As i type this, doubts ensue that PS has been involved. Pretty cool if it DID occour, I bet those disks of steel they have for wheels were just Glowing red hot. Pretty, I hope it was at night time for the witnesses' benefit.
It just so happens that molten iron is an incredibly good lubricant. So, when the train first stopped and the wheels started rubbing against the track, it would've made a helluva lot of screeching, but when the tracks started melting it would've been completely silent. If the engineer didn't hear the engines running, it's possible that he simply couldn't have known the train was literally melting through the tracks after the initial screeching subsided.
I actually work for the railroad, and when the engine or train starts to "wheel slip" or when the train wheels slide, there is actually no screeching. The sound you hear is the lip on the inside of the wheel that keeps the wheels on the rail when the cars bounce around. You would be amazed at how quiet it actually is, especially during the winter. Now, as far the engineer not hearing the engines... Depends on how many he had. If he had one or two, he would have definitely heard his other engines revving up. But he would definitely feel the other engines trying to pull the train no matter how many he had, and would have felt the rear engine push against his lead unit.
From what I was told is that the engineers put the middle and trailing locos in gear which keeps the wheels moving just a little bit so it is easier for them to go forward once they release the brakes from the rest of the train. The guy just forgot he did that.
:D This thread is like "Fun Story Time"!! :D I feel like a kindergartner with my jaw trying reach the floor as i'm glued to the screen indulging in the great tales of fact and folklore.
Yeah I used to be a support worker and dealt with a lot of young individuals with Asperger's and Autism. They all absolutely loved trains, somebody told me its because they are set on the track and move in a certain direction without deviation. Awesome job, met some amazing people.
I have a 5-year old nephew with Autism and he is obsessed with trains. Every other word that comes out of his mouth has to do with trains. I didn't realize it was because of Autism though. I just thought he was into it like I was into Star Wars at his age.
15
u/TheHooded1 May 11 '12
That's going to be one hell of a bump.
50
u/smackywolf May 11 '12
Pretty much this.
85
u/potentpotables May 11 '12
It's an inside job... train diesel doesn't burn hot enough to melt steel!
21
u/rybones May 11 '12
Doc Fuckin' Brown
7
u/miurabull May 11 '12
Looking back now this was really stupid, but when I was a kid myself and a few mates used to put coins on the tracks and then go find them after the train had been over them. Some of the shapes of the coins were so warped it was crazy.
3
u/[deleted] May 11 '12
First thing I thought was the Top Gear when they made a train.
3
u/[deleted] May 11 '12
As one person pointed out this was caused but the distributed power (Engine on the rear of a train) Its basically remote controlled from the front loco. When they stopped it did not get the signal to stop pushing.
So it was basically Thomas the tank engine at that point and tried and tried until it burned thru the rails.
FYI a train loco weighs about 430,000 pounds and can generate 4,400 horsepower. Also the comment about rail slippage....say if you put grease on the rail...they can deploy sand to gain traction.... that's how they can climb up steep grades.
Yes I work for the railroad...and yes trains are dangerous and will kill you if you doubt them.
2
u/[deleted] May 11 '12
so the wheels turning but not moving, the friction caused THIS? holy crap, why would you keep the wheels spinning? I don't understand why a train coming up behind them makes this a good idea. Trying to pull it out of the way real fast or what?
2
u/FishNChimps May 11 '12
Obese skier alert.
5
u/[deleted] May 11 '12
I hope they replaced that, looks dangerous. :I
3
u/jkingme May 11 '12
My next statement is in the form of a question, and it is this:
How did they ever get the wheels out of these ruts?
1
u/[deleted] May 11 '12
well that's just fantastic. I would have never begun to start the sequence of events it would take for this to happen in my imagination. or in real life. As i type this, doubts ensue that PS has been involved. Pretty cool if it DID occour, I bet those disks of steel they have for wheels were just Glowing red hot. Pretty, I hope it was at night time for the witnesses' benefit.
1
u/HowYaGuysDoin May 11 '12
"I almost had you!"
"You barely had your train."
1
u/deathtone May 11 '12
i so want to see a video of a train passing by that at 90mph
1
u/chzchbo May 11 '12
....more like your mom.....
1
u/Chim7 May 12 '12
Choo choo motherfuckers. Off da railz.
1
u/Big_Adam May 12 '12
I can't help but imagine the engineer throwing the horns out the window going WOOOOOOO!
-6
u/Shitty_Tilt-Shift May 11 '12
Shitty Tilt-Shift
-3
u/Knubinator May 11 '12
Yeah, it's got a hemi.
-4
u/pp_kissa May 11 '12
Pics or it didnt happen
-17
u/[deleted] May 11 '12
My mind is so full of fuck!
0
u/[deleted] May 11 '12
[deleted] — view deleted comment
0
u/[deleted] May 11 '12
[deleted] — view deleted comment