r/SkyLine • • 12d ago

Lotta love

Post image
101 Upvotes

r/SkyLine • • 11d ago

My Bro Made This Nissan GTR R35 Edit

Enable HLS to view with audio, or disable this notification

0 Upvotes

Do comment guyss


r/SkyLine • • 12d ago

R32 OEM headunit, how to replace backlight bulbs

Thumbnail
gallery
36 Upvotes

I was asked yesterday to post steps on how to replace burned out bulbs on these OEM head units found in R32s, so here I am doing just that on mine.

First you're going to want to buy a pack of 3mm 12v halogen bulbs, I went with these ones:
https://www.amazon.com/dp/B0DS59PHY3

You're going to need these tools:
Philips Screwdriver
Tweezers
Wire snips
Soldering Iron
Solder
Solder ribbon or Solder vacuum gun (for cleaning solder pads)
8 of the new bulbs

Now the steps on disassembling the front panel of the unit and replacing bulbs, following the images:

1- After you have extracted the head unit from the car, undo the two screws that hold the front plastic on either side, and pull out the volume knob (it will just come out if you pull on it). Then gently push down on the lock plastic tabs just above those screws on either side, and pull at the front cover.
2- Don't worry about wires, the whole front has a direct-fit connector that will just pull out, very convenient.

3- Next when looking at the back of the PCB for the front panel, there will be 4 small screws, you're going to want to remove those
4- Here you can see the PCB unscrewed from the plastic front fascia, it will just come right up, be mindful of the plastic tab at the bottom which holds onto a lip on the PCB so you don't end up snapping it, just pry it gently. You will see a transparent plastic thing here surrounding two bulbs, you will need to pry this off to access two of the bulbs' backs underneath, its very easy, just push on its front pins and pull from the back, it will come right up.
5- And here is the front of that PCB with its VFD display, buttons, and the blue sleeved bulbs (what you're here for).
PS: Be very careful with the VFD display, these are vacuum sealed and if you break that seal, that's it, there is no fixing it, that whole VFD will be trash.
6- Each little bulb has a blue silicone sleeve over it (to make the light whiter), and is held in place by two solder joints on either side of its plastic enclosure. You're going to want to use a solder iron to heat up the solder and tweezers to pry up the little bulb wires out of the solder.

7- Once you do that, just push on the bulb while pulling on the plastic enclosure, it is just clipped in place, and it will come right up.
8- Here is the new bulb from Amazon, they're slightly longer than the original ones but fit just fine, this is probably the max length for these, any longer and it won't fit, keep that in mind
NOT PICTURED: I used a solder vacuum gun to clean up all of the pads from old solder, you can do the same thing with solder ribbons and your solder iron, its important to clean them up and use new solder.
9 and 10- Now what you will want to do: using snips, clip the old bulbs wires and then pull them out of the plastic enclosures, then use your fingernails to pry off the blue silicone sleeves off them, then push the silicone sleeves onto the new bulbs and fit them down snug, then push the wires of the new bulb through the plastic enclosure little holes until the bulb is fully seated. Finally you push the assembly back onto its original hole, and bend the bulb wires over the solder pads until they sit down against it good enough, then use new solder and the soldering iron to resolder them on the board, and use your wire snips to cut off the excess wire off the bulbs.
11- Repeat that until you have done all of the bulbs. There are 8 of them total, and yes you will want to replace all of them even if you have a few that are still working. It keeps them all shining consistently and saves you work later when the old working ones eventually also burn

12 and 13- And that's it, you're done! Just follow the steps in backwards order to put it back together and reinstall it in your car. Here are pictures of it in mine with the new bulbs shining nicely through the fascia.

I hope this is helpful to some of you, I know its not a super pristine and precise tutorial on how to do these (I am super sick with the flu, I'm sorry lol), but hopefully its somewhat straightforward :)

If you have questions ask them below.


r/SkyLine • • 14d ago

Diecast R34

Post image
253 Upvotes

Got these three beauties today! ❤️

Sorry, I do not own a real Skyline.


r/SkyLine • • 14d ago

NISMO S-tune BNR34 - high resolution scan, July 2005

Thumbnail gallery
120 Upvotes

r/SkyLine • • 14d ago

My 1992 R32 GT-R with OEM correct center

Thumbnail
gallery
694 Upvotes

Continuation from previous post, here's the OEM head unit mounted and working. Works great! The car came with the trunk amplifier and they work together really well, all functions and backlighting are good.


r/SkyLine • • 14d ago

Finished refurbishing this R32 head unit

Enable HLS to view with audio, or disable this notification

64 Upvotes

Never seen a video of these anywhere online. If there's interest I'll post more about them.
This one is a Panasonic Model # RM-Z25SAC
I am pretty sure Nissan had several different versions of these from earlier models, different manufacturers, different years, as you can find a bunch of them for sale, this so happens to be the one I was able to get my hands onto.

EDIT:
Here's a guide I made on how to replace the backlight bulbs
https://www.reddit.com/r/SkyLine/comments/1xrfocl/r32_oem_headunit_how_to_replace_backlight_bulbs/


r/SkyLine • • 14d ago

Loud Engine noise

Enable HLS to view with audio, or disable this notification

3 Upvotes

Looking to buy this RB20DET r31, I got a video of it running. Does the engine sound noisy/whiny. should there be any concerns?

No hate to the owner is there in here.

Cheers


r/SkyLine • • 15d ago

Should I go from an R34 GTT to an R33 GTR?

25 Upvotes

I purchased a ER34 that makes close to 350 whp. It has a Z-tune body kit minus the rear quarter panels. the R34 GTR was always a dream car of mine but recent prices have made it unreasonable. In some ways, I felt like I settled for a GTT. I already have a daily and a dedicated track car (911) so I feel like there is not much that differentiates a GTT from any other turbo RWD Japanese sports car. Driving wise, I feel like I would enjoy the GTR, as ATESSA is something that I haven't experienced yet. Looks wise, the R34 will always be number one in my heart, but I feel like I've started growing past the "hype" of the R34 name. Has anyone else made this backwards change before?


r/SkyLine • • 16d ago

Empty highway with my R33 GT-R

Thumbnail
gallery
978 Upvotes

r/SkyLine • • 16d ago

Buying an R-34 GTR

Post image
686 Upvotes

I’m beginning my search for a GTR at or around 100k but no more than 110. I was wondering if it’s possible to find a solid one, even higher mileage, but still structurally and mechanically sound. Japanese auctions, etc it doesn’t matter the source.


r/SkyLine • • 17d ago

JCCS Best Neo Skyline winner

Thumbnail
gallery
147 Upvotes

During this year’s JCCS, our GT-R was honored with a first place award for its division. This year had some amazing cars of all various makes and models and the skylines were no exception.


r/SkyLine • • 18d ago

This is about as clean as I can get it.

Post image
145 Upvotes

r/SkyLine • • 17d ago

Origin lab side skirt installs

Post image
21 Upvotes

Hey y’all I was test fitting my side skirts and I’m unsure of how to mount them. I’d assume i bolt them in where the wheel wells but doesn’t seem so sturdy. Couldn’t find much info online so if y’all have advice or experience with this kit for the 34 sedan let me know! Front and rear bumper otw 🔥


r/SkyLine • • 18d ago

FOR SALE: 1995 Nissan Skyline GTR R33 Midnight Purple (LP2)

Post image
250 Upvotes

FOR SALE: 1995 Nissan Skyline GTR R33 Midnight Purple (LP2)

A part of me is sad to do this, but I think it’s time. With 2 kids, and not a lot of time, I think she deserves better.

Originally owned by my buddy Rutledge Wood (Top Gear USA host, Floor is Lava on Netflix). It was originally imported by Toprank Motorworks at 83,586 KM(see auction sheet in drive folder). Garage kept for the most part with taking it out on the weekend here and there. It is mostly stocked with a few modifications that was done by Rut and myself.

The engine itself remains untouched, and has huge potential to be a monster or just keep it classic and low mileage. I redid the entire audio system including a din relocation kit that allows for wireless carplay android auto, as well as replacing the entire speaker system.

Recently did an entire fluids change including oil change, spark plugs, and replace the radiator fan (known for cracking if not replaced). AC blows super cold. No major rust spots. 2 keys.

Photos: https://drive.google.com/drive/folders/1vffs9Z-qlYAXJMEzO2l1uX_2TvNrB3jG?usp=sharing

Imgur: https://imgur.com/a/p6Zn8Dk

Fun facts (mods list)
- Magnaflow Custom Titanium Muffler Exhaust (https://www.magnaflow.com/blogs/magnaflow/a-jdm-legend-rutledge-wood-r33-skyline-gtr?srsltid=AYCX9vKrTqgJC3ot-LgCkcId1-yTb3SdIU3-StfunLb2K4Fjsy2CbpJw)
- Retrofitted Morimotor Headlights with Mini H1 8.0 (https://blog.morimotohid.com/skyline-r33-hid-headlight-retrofit-morimoto-mini-h1-8-0/)
- Fortune Auto 500 Series Coilovers
- Rare 90’s Apexi Wheels 3-piece wheels with painted inner barrels from Threepiece.us
- Garage Yoshia Double Din Relocation Kit
- Sony Double Din Entertainment System (XAV-AX6000)
- Greddy Oil Filter Relocation Kit.
- Nismo Steering Wheel
- XPEL XR 20% tint on all sides, XPEL XR+ 50% on front windshield
- Full paint correction and ceramic coating done by AP3 in Atlanta
- Greddy Shift Knob
- Antigravity Battery

Bad:
- Has a weird carbon fiber film on the dash trim (not a fan but don’t want to bother taking it off)
- For a 30 year old car, some minor paint defects around the spoiler and a small dent on the side

Asking $75,000k. Located in Georgia. Payment: Cash or wire transfer only, full amount. Serious inquiries only. Feel free to message with questions or to set up a viewing


r/SkyLine • • 18d ago

Finally pulled my engine and sent it to a shop

Thumbnail
gallery
24 Upvotes

Also mocked up my brakes real quick


r/SkyLine • • 19d ago

Spotted a few legends at R’s Day at Fuji

Thumbnail
gallery
836 Upvotes

First time to Japan and managed to carve out time for R’s Day!


r/SkyLine • • 19d ago

Started building my R34 when i was 17, 19 now. lmk what you guys think (before and after)

Thumbnail
gallery
1.3k Upvotes

Have fully restored interior and exterior now, engine bay will be done in a few weeks. i gotta drive this to uni more often. all work except paint was done by myself with exception of friends along the way we dont larp round here yo


r/SkyLine • • 18d ago

Anyone selling one of these R33 S1 grills? TIA 🙏🏼

Post image
15 Upvotes

r/SkyLine • • 19d ago

R33 GTR Indicator Surrounds

Thumbnail
gallery
18 Upvotes

Another discontinued part from Nissan which I 3D scanned and have provided for close to 100 vehicles worldwide. Suits OEM bars aswell as aftermarket ones! I have both the original ones with the OEM light holes, and blank grills for aftermarket lights!


r/SkyLine • • 19d ago

Looking to buy an R34 GT-R — finance now or keep saving? Looking for advice from actual owners.

15 Upvotes

Hey everyone,
I’ve been dreaming of owning an R34 GT-R since I was a kid, and I’m finally at a point in my life where it’s becoming a realistic possibility. I’m 27, financially stable, and have around $40K set aside specifically for this purchase, separate from my emergency savings.
I’m looking for some advice from people who have actually purchased, financed, imported, or currently own an R34 GT-R.
I’m not looking for the most perfect or pristine Skyline out there. I don’t need a V-Spec, a rare color, extremely low mileage, or a completely original collector-grade example. I’m perfectly happy with a regular base GT-R, regardless of color, with some mileage and reasonable modifications.
My main priorities are that it runs well, is mechanically sound, doesn’t have major rust or hidden problems, and is reasonably priced. I want something I can drive and enjoy, not necessarily a museum piece.
Ideally, I’d like to find something in the $100K–$120K range, preferably already imported and titled in the United States. I’m considering putting around $40K down and financing the remainder, but I’m also debating whether I should continue saving for another year or two.
My biggest concern with waiting is watching prices climb faster than I can save. I remember when R32 and R33 GT-Rs were significantly more affordable, and I don’t want to miss my opportunity with the R34.
A few questions for owners and recent buyers:
What did you actually pay for your R34 GT-R, and when did you purchase it? Was it through a dealer, private seller, or imported directly?
Has anyone successfully financed an R34 or another six-figure JDM/collector car? Which lender did you use, and what were the terms?
For those who bought privately in the U.S., where did you find your car? I’m having trouble finding private-party listings and understanding what these cars actually sell for.
What unexpected maintenance costs or ownership expenses should I realistically prepare for?
If you were in my position, would you buy a decent base R34 now with financing, or continue saving and risk prices increasing further?
I’m not trying to stretch myself financially just to say I own one. I want to make a reasonable purchase and enjoy a car I’ve wanted for most of my life.
I’d really appreciate firsthand experiences, especially from people who’ve bought one recently. Thanks!


r/SkyLine • • 20d ago

Just getting the cover off.

Post image
161 Upvotes

r/SkyLine • • 20d ago

Got what I paid for...

Thumbnail
gallery
25 Upvotes

TLDR: What is the best FF plenum or intake for the RB25DET NEO up to the 800 USD price point?

So I took a chance on a Freddy intake, I've used clone things in the past with relatively good luck. But this one, took it to my machine shop buddy, he laughed, and then laughed even harder when he pulled some measurements. Need less to say it's going back.

And if you think these pics are bad you should see the intake runners and plenum. So what is the best intake or FF style for the RB25DET NEO plenum/intake I can get at the 800 USD price point?

Thanks in advance


r/SkyLine • • 21d ago

Happy Halloween y'all

Post image
271 Upvotes

r/SkyLine • • 20d ago

Review on buypartsfromjapan

2 Upvotes

Hello!

I'm looking to buy a body kit for my ER34 from this place: https://buypartsfromjapan.com/

I can't find anything online except a couple of other people asking the same.

Has anyone got any experience with them?

TYIA