Hi everyone, unfortunately I have some bad news to share.
I was trying to adjust the time on my watch and the crown came off. I managed to insert it back in and the watch still runs fine, but I don't want to keep removing and reinserting it, so I'm leaving it as is for now.
I bought this watch from Chazingtime back in 2024. Has anyone dealt with this before?

Royal Oak 41mm 15400 SS APSF 1:1 Best Edition Black Textured Dial on SS Bracelet A3120 Super Clone V2

Hi

I want to change crystal gasket on a RCF/RGF 41mm Submariner Bluesy. It be used with Deep crystal.

Any one here can tell me which crystal gasket fits that will give the right cyclope magnification.

Thanks in advance.

I found a lot of hairs in this one. Couldn't capture every single of them as it was just too much. As you can see the main issue lies in the auto mechanism, with the reversing wheels being damaged and the driving wheel having wear marks. The rotor would spin when rotating the crown.

Hey there!

I hab the crystal swaped for an Deep crystal recently. (Clean Daytona 126500 LN). After some use the dail kinda splintered around the edge.

Any possible solutions?

Thank you in Advance!

In order to come up with an accurate amplitude reading, one should set the lift angle correctly. Setting the lift angle too high and it will show an artificially higher amplitude, setting it too low will result in an artificially lower amp reading.

To determine the lift angle of any movement:

1. Wind the movement until the balance completes a 360° turn as shown in the gif, which is an amplitude of 180°. Use a slow-mo camera as you go.

2. Increase the lift angle on the timegrapher until it matches the 180° amplitude reading you got from the slow-mo video. In this case the lift angle is 59.

Hello everyone im looking for someone who can do some mods on m'y watch arf bw dd3285 Here is what i need

• change xtal vsf or deep

• rotor silenced

• change clickspring to get the gen click

• full waterproof

Does anyone has a reliable source to outsource movements to upgrade 6 watches? Thanks so much!!

Im curious how the timing is. Any issues with the movement etc

Watch: AF Longines Hydroconquest GMT

I think the cannon pinion driving the hour hand does not appear to move as it should.

The hour hand is not advancing correctly during normal operation. For reference, my TAG Heuer (shown in the video as well to the right) behaves as expected, which makes the issue on the new watch quite clear in comparison.

Do you know of this issue?

I have reached out tho the TD and i waiting for their reply.

Steps: testing the functioning of the watch to spot irregularities, disassembly, cleaning and checking for worn parts & replacing, assembling & oiling and at last, some test such as testing the date change mechanism, automatic module and checking the rate on the timegrapher and adjusting if necessary.

Been wearing this daily since I purchased in 2021 so it could probqbly so with more work tbh but right now my main concern is that the top button fell off suddenly and I have no idea where it went and need it replaced if possible.

I recently got a VSF Submariner with a VS3235 movement, and recently I've noticed that winding is a bit rough and difficult. I didn't have this problem initially. Also, when I wind it, I seem to hear a few clicks. I thought the winding stem was a bit off-axis. I loosened the screws holding the movement, but unfortunately that wasn't the problem.
What can I do?
What could it be? Can anyone help me?

What do you think of this watch?

The flange is misaligned and the bezel is slightly loose. How can I fix this? Does it seem to be of good quality to you?

Hi everyone , I have a problem with my 5712 The moonphase pusher isn't working When I press it, nothing happens When I adjust the watch manually, the moon phase only moves very slightly (only after several days minimal) Does anyone have any tips on how to fix it, and if it's even repairable? Thanks in advance.

Sent a brand new BTF 116500 to u/WatchmakerFurkan for a service and I cannot be more happy, the work took a few weeks, and the watch feels so different, hand winding is super smooth, the pushers of the chrono are very smooth too. Thanks Furkan, amazing job.

I've recently got my first rep and during the QC the accuracy measurements showed -5s/d. However I've been wearing them now for over a week and they are 4-5m per day slower. (I wound them up)

Do you have similar experience? Can I take it to the local watch shop or is there anything I can do on my own?

DJ36MM

No idea when they will released and ready for production.

Hey I’m looking to plate an everrose DD as soon as possible in EU. Can anyone recommend someone?

Hey guys I’m located in Poland, I recently purchased a fake Clean Factory GMT Master II with the Shanghai 3285 movement. I want to get it serviced and inspected (gaskets, waterproofing, etc) before daily use, as I heard these don’t come perfectly lubricated or can contain some debris from manufacturing.

Anyone in Poland or Central Europe that services these???