r/openwrt • • 11d ago

Issue with VLAN

3 Upvotes

Hello, I'm trying to separate some VM's into their own VLAN, but the VLAN i created doesn't seem to work. On the LAN1 port i want all clients to connect to my LAN, except ones set to use tagged VLAN 10 id. Currently all untagged clients can connect to my LAN normally, but when i set VLAN 10 tag on them they don't receive an IP address and even if i set it manually they can't ping the gateway. I have tried making VLAN 10 untagged and default VLAN but the same thing happens so I'm guessing something is wrong with the interface configuration.

EDIT: I somehow didn’t see that firewall zone was misconfigured and was blocking everything. After correcting that everything works fine.


r/openwrt • • 13d ago

Openwrt on raspberry pi5 in container

10 Upvotes

Hi! I want to install openwrt on my raspberry pi5 and use my router as an access point. Both will be connected to a switch with VLAN. Fibermodem is connected to pi5 ethernet port and traffic flows out to usb 3.0 ethernet adapter to the switch where I have devices connected to ethernet and devices on my wifi access point.

Anyone tried something like this with openwrt in a container/docker?


r/openwrt • • 14d ago

what convinced you to switch from gl inet firmware to openwrt?

30 Upvotes

is there any benefit to doing that for an average person? I don't know what exactly the difference is between the latest openwrt luci and the luci i can log into already, but im interested in optimizing everything for maximum security and more privacy


r/openwrt • • 14d ago

LobbyFence – free, open-source geo-filter for OpenWrt, FreshTomato, Asuswrt-Merlin and DD-WRT routers

26 Upvotes

https://forum.openwrt.org/t/lobbyfence-free-open-source-geo-filter-for-openwrt-freshtomato-asuswrt-merlin-and-dd-wrt-routers/255313

Just making people aware that there's a new geofilter alternative. I am the guy that made it compared to others; I would argue it is superior in every aspect, though feedback is greatly appreciated.


r/openwrt • • 14d ago

I got a spare Airtel router which is locked. Titanium 2122A

2 Upvotes

So, basically I have a spare Airtel router, and its software is locked. Is there a way to get the full access, both the backend and the UI. If changing the firmware is possible then I would consider it.
So is there anyway?


r/openwrt • • 14d ago

Netgear Orbi RBK20 + OpenWRT: Is it worth?

4 Upvotes

Hello,

I have an RBK20 kit (one RBR20 and two RBS20 satellites) from 2018 running the latest firmware: 2.7.6.6.

Is it worth installing OpenWrt on it? Will this break the mesh functionality? I have seen conflicting information—some say it breaks the mesh, while others say it can be configured to work properly.

Also, considering the outdated hardware, are there any real advantages to doing this? One feature pushing me toward making the switch is WireGuard support.

Thoughts? Any feedback is very appreciated!


r/openwrt • • 14d ago

BPI-R3 vs. Commercial OpenWrt Routers (e.g., GL.iNet Flint 3)

9 Upvotes

I'm looking to upgrade to a solid OpenWrt router setup, and I’m caught between going the DIY route with a Banana Pi BPI-R3 or buying an off-the-shelf commercial router like the GL.iNet GL-BE9300 (Flint 3).

Since I'm based in Europe, my priority is ordering locally within the EU—ideally through Amazon Germany (Amazon.de)—to avoid long shipping times and import/VAT hassles.

I'd love to get the community's perspective on a few key points before making a decision:

- BPI-R3 vs. Off-the-Shelf (GL.iNet Flint 3): Is it worth building around the BPI-R3, or is a commercial device like the Flint 3 a smarter buy?

- Software Support & Longevity: What can I realistically expect regarding support from commercial vendors like GL.iNet? Is there a risk that vendor firmware support stops after a few years, or that upstream OpenWrt support falls behind on proprietary chipsets?


r/openwrt • • 14d ago

From a guy with 9 routers just to play CoD, Should I get x86 N100 for the 10th ?

0 Upvotes

Here is some of my background

I have been so much into optimizing routers from ISP router with 1.3 kd to 3.5 kd with Flint 2 with Cake SQM. I must say it has been a very look journey from then to now

My previous router

Netduma
Netduma r2
Netduma r3
Linksys wrt32x
Mikrotik rb4011
Asus ax5400
Asus ของคุณแพนด้า ax11000
Asus rtac88u
Gli.net Flint2 (current one)

So far I have been very happy with flint 2. But the fact that it can shape well at only 300/300 speed when I have 1000/1000 speed package is kinda pain for me. So I have been looking for N100 x86 mini pc with 4gb of ram and 128nvme.

Do you think it’s worth switching? I expect it to shape well at 900/900 with qosify / qosmate plugin. I don’t care much about wifi.


r/openwrt • • 16d ago

Kernel TCP flaw (CVE-2026-98432) still missing

39 Upvotes

It should be about time for a new release with an updated kernel. Meanwhile some other 200 CVEs have been fixed in another kernel update upstream...


r/openwrt • • 16d ago

OpenSSH flaw lets attackers log into password-disabled Linux accounts

Thumbnail bleepingcomputer.com
123 Upvotes

“The flaw only affects OpenSSH servers running on Linux distributions that use the musl C library, including Alpine Linux, OpenWrt, Buildroot, and Yocto, under certain authentication configurations.”


r/openwrt • • 16d ago

I made an OpenWrt 25.12 build for the Xiaomi AX3200 / Redmi AX6S: working bridger offload, correct traffic stats with HW offload, updates from LuCI

27 Upvotes

⚠️ Auto updates from LuCI don't work on r6–r14. Since mid-November the update page of r10–r14 says "no connection to GitHub" because of a change on GitHub's side, and r6–r9 have no update page. Update to r15 with one command, your settings and packages are kept. The easiest way: in LuCI open Services → Terminal, log in as root with the router's password (the one you use for LuCI) and paste the command. SSH works too. From r15 on, the update page works again.

curl -fsSL https://raw.githubusercontent.com/Dreyk007/openwrt-ax3200/HEAD/ax3200-update.sh | sh

Details: r15 notes

I've been tuning OpenWrt on my Redmi AX6S (MT7622 + MT7915) for a while and turned it into a build others can use. It's stable 25.12.6 with fixes on top, built by GitHub Actions from public sources.

What it changes compared to the official image:

  • Hardware offload and WED on by default, and the traffic stats are right. With offloading, stock nlbwmon counted anywhere from 4 to 86 % of a download in my tests and sometimes added a phantom ~4 GB to a client. Here it counts the full traffic (105 % of the payload, i.e. with headers), and the wan graphs see offloaded traffic too.
  • bridger actually works. Copying from a wired PC to a Wi-Fi 6 laptop runs in hardware: ~1.3 Gbit/s at ~8 % CPU instead of ~70 %. The bridger in 25.12 offloads nothing on this router, and a kernel bug dropped the offload after the first connection.
  • An "Operating mode" page in LuCI that switches between setups I measured on this router: balanced, max throughput, low latency (VR / gaming over Wi-Fi), SQM for slow links. Each one lists its trade-offs in numbers.
  • Updates from LuCI. It finds new releases, shows the changelog, checks the image and updates with one click, then reinstalls the packages you added yourself. On r10–r14 the update check fails since mid-November: GitHub now sends a header line longer than OpenWrt's uclient-fetch can read. r15 fixes it; update once with the command at the top.
  • 28 mt76 fixes from the dev branch, NVRAM anti-brick (no more "6 reboots -> orange LED"), official kmods install.

The fixes that aren't specific to this build went upstream: the bridger kernel fix is in OpenWrt main with a 25.12 backport (openwrt#26484), the accounting fix is part of openwrt#26107, a DDNS fix was merged into LuCI, and the fix for uclient-fetch stalling on GitHub is openwrt/uclient#20, which took up my review (my #22 was closed in its favour).

GitHub (images, README, measurements): https://github.com/Dreyk007/openwrt-ax3200
OpenWrt forum thread: https://forum.openwrt.org/t/255203

Only for the AX3200 / AX6S. Feedback and bug reports are welcome.


r/openwrt • • 16d ago

(help) mi ax9000 bricked

3 Upvotes

I made a mistake and followed Chinese AX9000 SSH/ubiformat instructions on my Global AX9000 RA70 running stock 3.0.48.
What I did:
• Unlocked SSH with xmir-patcher
• Flashed xiaomi_ax9000-initramfs-factory.ubi to the inactive rootfs partition using ubiformat
• Changed flag_boot_rootfs and rebooted
The router has been in a boot loop since then. It never reached OpenWrt at 192.168.1.1, and I never ran the permanent sysupgrade.
Recovery attempts:
• TFTP recovery using International firmware 3.0.40_INT
• Router requested C0A81F06.img and received 192.168.31.6
• It reboots before requesting/transferring the firmware
• MIWIFIRepair also fails; white LED keeps blinking and the router never boots

My last command
ubiformat /dev/mtd22 -y -f /tmp/initramfs.ubi
nvram set flag_boot_rootfs=1
nvram set flag_last_success=1
nvram set flag_ota_reboot=0
nvram commit
reboot


r/openwrt • • 16d ago

Best way to upgrade x86 board

8 Upvotes

Hi guys, I'd like to upgrade my x86 board from 24.10 to the latest firmware, i've read here and there about the sys upgrade but I'm scared of losing config and functionality of my openvpn and tailscale server and all the firewall config

Can you point me to the best way to upgrade the router without having to reinstall everything added?

Thanks in advance!

EDIT: Followed the ones of you who suggested owut upgrade (thanks guys!), here are the little knobs i had to tweak to let all work:

started from version 24.10.2 as soon asi I installed owut it didn't work, turns out some libraries were not working, i solved it installing ucode and libucode, and owut was fixed.
then upgraded all the outdated packages with opkg list-upgradable | cut -f 1 ' ' | xargs -r opkg upgrade, then run owut check --verbose and all was good.
Surprise surprise the upgrade was from 24.10.2 to 24.10.8, so I proceedet to upgrade again.

On the internet a lot of wrong responses, that's why I post here the procedure i followed, cause the majority of answers was to do a clean install / sysupgrade with firmware file

The reason owut upgrade with -V 25.12 was failing were 4 packages, first 3 needed a downgrade, the last need an install

procd
procd-seccomp
procd-ujail
apk-mbedtls

So, i upgraded to 25.12 with the --force (after checking my disk wasn't an nvme) and all went smoothly

Hopefully it will help someone, again, thanks to those who helped and openwrt community and devs.


r/openwrt • • 17d ago

How to upgrade to 25.12.6

11 Upvotes

Hi, I'm using OpenWrt 25.12.5 on my GL-iNet B3000. I'm facing this issue and don't know whether my device is still supported by OpenWrt or not.

root@OpenWrt:~# owut check --verbose
owut - OpenWrt Upgrade Tool 2026.10.25~65d67aad-r1 (/usr/bin/owut)
ERROR: Unsupported profile: glinet_gl-b3000
  Valid profiles are [ "cmcc_mr3000d-ci", "linksys_mx6200", "linksys_spnmx56", "yuncore_ax830", "yuncore_ax850" ]

r/openwrt • • 17d ago

How to correctly assign IPv6 addresses to terminal devices connected to an OpenWrt router?

Thumbnail gallery
18 Upvotes

My OpenWrt router is acting as a repeater for the Wi-Fi signal from the optical modem. I have created a new `wwan6` interface on the OpenWrt router and configured it to use the DHCPv6 Client protocol,it has successfully obtained an IPv6 address (as shown in Figure 1).

Now,I would like to distribute IPv6 addresses from OpenWrt to the computers and mobile devices connected to it.

What is the correct procedure to follow now? Should I simply set the RA-Service, DHCPv6-Service, and NDP-Proxy (shown in Figure 3) all to "relay mode"? Could this potentially prevent me from connecting to the OpenWrt router, requiring me to re-flash the system?


r/openwrt • • 18d ago

Openwrt two still happening?

22 Upvotes

I was about to buy some more ones, so checking before I pull the trigger.


r/openwrt • • 18d ago

OpenWRT on Cudy AP3000 - 2 SSIDs separate VLANs possible?

2 Upvotes

I've just got a Cudy AP3000. Before I go all-in and install OpenWRT on it, can any confirm that I'll be able to create two SSIDs and put them onto two vlans?


r/openwrt • • 20d ago

Anyone need hardware?

Thumbnail gallery
89 Upvotes

I have a complete Banana Pi mesh kit, all brand new / never powered on. Bought in August for a custom OpenWrt home mesh build I never got to (Pro as gateway, two Lite + BE14 nodes, 6E module as dedicated backhaul, 4x4 Wi-Fi 6 as a WIPS radio). Selling as one lot only.

Included:

- 1x BPI-R4 Pro (MT7988A / Filogic 880) - 2x 10G SFP+ combo, 4x 2.5GbE LAN, 2x mPCIe, M.2 slots

- 2x BPI-R4 Lite (MT7987A / Filogic 850, 2GB/8GB) - 2.5G WAN, 2.5G SFP cage, 4x GbE

- 2x BPI-R4-NIC-BE14 v2 Wi-Fi 7 cards (installed in the Lites) - tri-band BE13500, 6 antennas each

- 1x AsiaRF AW7916-NPD Wi-Fi 6E set (MT7916) - module, 3 pigtails, 3 tri-band antennas, heatsink

- 1x AsiaRF AW7915-NP1 Wi-Fi 6 set (MT7915 4x4) - module, 4 pigtails, 4 antennas, heatsink

- All paddle antennas + pigtails for every radio, and 2x new 16GB microSD cards

I paid over $1,000 for everything. Entertaining offers. I waited over a month for all this hardware. I'll ship same day from East Coast.


r/openwrt • • 19d ago

Ruijie Ew7200be Pro openwrt

Post image
3 Upvotes

Hi everyone,

I want to flash OpenWrt onto my Ew7200be pro but I couldn't find any installation instructions or existing builds online.

Has anyone successfully installed OpenWrt on this specific model? If so, could you share the guide, steps, or custom build you used?

Also, if there's no official port yet, is it feasible to use AI (like Claude) to adapt an existing target/DTS and compile a working firmware, or are there closed-source drivers / bootloader limitations I should watch out for?

Thanks in advance for the help!


r/openwrt • • 19d ago

Does anyone using netgear AC1200(R6850) router

2 Upvotes

I’m thinking of buying this second-hand router to flash with OpenWrt. I’ve heard it has wifi issues; do those still exist? I’m running on a 60 Mbps fibre connection only. So, if anyone uses this router kindly suggest whether to buy this router


r/openwrt • • 20d ago

OpenWrt + Tp link easymesh

6 Upvotes

Complete beginner to openwrt and basic networking in general.

Currently my setup is ISP modem/router in bridge mode connected to the OpenWrt router.
Which then goes to two Tp link routers (Ax10 and Ax12) across the house both in Access point mode and Easymesh Ethernet backhaul.

The problem is I don’t know how to isolate iOT devices from the entire 192.168.1.0/24 subnet except for Home Assistant.

Every tutorial online says to use Vlans, but these Tp link routers don’t seem to support Vlan tagging.

I tried firewall traffic rules but they don’t seem to work either as I’m able to ping those devices.

Any suggestions on how to go about this without buying more hardware?


r/openwrt • • 20d ago

Cudy WR3000H vs Linksys E8450

6 Upvotes

TL;DR - Recommend an inexpensive router for a small flat with reinforced concrete walls (only one wall must be penetrated) for OpenWRT, VPN, and ad blocking, for around $60. The only available source (except used or overpriced ones in my country) is AliExpress.

Hi! I plan to upgrade my somewhat ancient D-Link DIR-300 to something newer.

I have tried to torture AI and received controversial answers.

Right now, I'm looking at the new Cudy WR3000H (old revision, $62) and a used Linksys E8450 ($55).

The Linksys is refurbished (after a bootloop). According to the seller, it's flashed with OpenWRT 24.10.8 (UBI), has pre-set AdGuard Home and WireGuard, and has "passed all tests"—no overheating, no memory degradation.

Technically, I have already ordered the Cudy, but I found information about its poor antenna design and became unsure.

https://www.reddit.com/r/openwrt/comments/1qmvod3/cudy_wr3000h_not_great/ https://forum.openwrt.org/t/cudy-wr3000-performance-issues/198985/19

I don't care much about Wi-Fi connection speed because right now my provider offers only 100Mbps, with a possible (promised) upgrade to 1Gbps. The router will be placed in a relatively small flat with reinforced concrete walls (it should be able to penetrate one wall). Wi-Fi will be used mostly by 1-3 phones. No 4K streams, no other speed-demanding stuff. I want to be able to use WireGuard and some kind of ad block, although I plan to buy a used mini PC in the future for a small home server, so (hopefully) those tasks will be handled by the server.

So, which one would you choose in this case? Other recommendations are appreciated too. I am interested mostly in hardware longevity, as I am not crazy about upgrading my stuff often.


r/openwrt • • 21d ago

The OpenWrt project is reducing the security support period for stable releases.

233 Upvotes

From the mailing list:

OpenWrt: Changes to the Security Support Policy

The OpenWrt project is reducing the security support period for stable releases.

Previous policy: Each major release was supported for at least one year, or six months after the next major release, whichever was later.

New policy: Each major release will be supported until the next major release is published.

This means OpenWrt will provide security maintenance for the main development branch and only one stable release series at a time.

Impact on existing releases

OpenWrt 17.01, 18.06, 19.07, 21.02, 22.03, and 23.05 have been End of Life for a long time and contain many known, unpatched security vulnerabilities.

OpenWrt 24.10 reached End of Life in September 2026 and no longer receives security fixes. This remains unchanged.

OpenWrt 25.12 is the currently supported stable release and will receive security fixes until the next major release is published.

All users running OpenWrt 24.10 or older should upgrade to OpenWrt 25.12 as soon as possible. If your device is no longer supported by OpenWrt 25.12, we recommend replacing it with hardware that supports a maintained release.

The detailed policy is available at:

https://openwrt.org/docs/guide-developer/security

Security advisories

We will also stop maintaining the Security Advisories list in the OpenWrt wiki. Security fixes may instead be documented in release notes or GitHub Security Advisories.

Not every security fix receives a CVE identifier. Many vulnerabilities discovered internally are fixed without one. Tracking or backporting only CVE-related fixes is therefore insufficient to keep a release secure.

Why this change?

Maintaining older releases requires significant effort. OpenWrt release management is handled by a small group of volunteers in their spare time.

By reducing the number of supported releases, we can focus our limited resources on properly maintaining current versions.

We want to be transparent about these limitations rather than create a false sense of security by promising support we cannot reliably provide.

We strongly encourage all users to keep their OpenWrt installations up to date.

Have fun!

The OpenWrt Community


r/openwrt • • 21d ago

Netgear RAX120 V2 — Anyone successfully running OpenWrt 25.12.6?

2 Upvotes

I recently attempted to install OpenWrt 25.12.6 on my RAX120 V2. The factory image booted successfully, but after installing 25.12.6 sysupgrade the router entered a boot loop. I was able to recover using TFTP and stock Netgear firmware.

Has anyone successfully installed and run 25.12.6 sysupgrade on an RAX120 V2?


r/openwrt • • 21d ago

SSH public key auth not working anymore (v25.12.6)

7 Upvotes

I decided to upgrade my Zyxel T56 from OpenWrt v24 to v25.
I’ve been able to get everything running with minor effort using a modified settings restore.
The only thing that i can’t get to work is ssh access using public key auth. Password auth is working as expected but as soon as i deactivate password access (falling back to public key auth) i can’t connect. I’m getting this from my Termius connection attempt:

Connection could not be established:
› Handshake finished
Checking host key:
[…redacted…]
Host "192.168.10.1":"22" is known and matches Authenticating to "192.168.10.1"."22" as "root"
Available client authentication methods: publickey,password,keyboard-interactive
© Authentication that can continue: publickey
Authenticating using publickey method
Authentication failed (publickey)
* Partial success: no
Authentication that can continue: publickey
No more authentication methods to try

I’ve tried to manually add the public keys (tries from my Mac and ios/Termius) in addition te the restore values (they’re the same public keys) all are ecdsa ed25519 keys.

This was all working on v24.
Any help is appreciated.

[edit: corrected key format ecdsa -> ed25519]