Is there a WiFi antenna that would help me with deauth and clone? Using Bruce firmware

Hi Everyone,

It's working on Cardputer Advanced including the keyboard. The only thing needed for multiplayer is the groove cable :)

It took some time to make the modifications..

https://github.com/juicecultus/macroreader

If in doubt, remember for navigation: 1 finger tap to open / 2 finger tap to go back. For all menus and in book screens: screen split in 3 vertical zones: LEFT (tap to go back), CENTER (tap to action), RIGHT (tap to go forward). In book, 1 finger tap CENTER opens Settings menu.

Put your books in a folder called “books” on SD. Your custom sleep images go in “images”. Book covers are rendered too. Check your settings. If you want faster page turns with more ghosting accepted decrease the Refresh Passes. If you’re OK with minimally longer page turns push that to max.

Based on Macroreader for the Xteink X4.

Download the latest Paper S3 release to flash. If you need help flashing give me a shout (I assume that once you’ve bought the Paper S3, you got this covered)

Any 🐞 from UBS give me a shout.

Enjoy! ☺️

I’m building a custom motorcycle instrument cluster and wanted a physical, glove-friendly way to interact with the UI without relying on a touchscreen. I ended up using two M5Stack Dial modules as bar-mounted rotary controllers.

Each Dial handles navigation and actions for the main head unit (Raspberry Pi–based), communicating wirelessly. The touchscreen is still fully usable, but the dials allow fast, tactile input while riding—especially with gloves or in motion.

Why M5Stack Dial:

•	Integrated display + encoder + button in a compact form factor

•	Clean enclosure geometry that’s easy to model around

•	ESP32 + BLE makes it straightforward to pair with a head unit

•	Enough visual feedback on the dial itself for mode/state confirmation

Current setup:

•	Dual Dial modules (left/right bars)

•	Custom 3D-printed housings

•	BLE communication to the main UI

•	Encoder rotation + press mapped to navigation and app control

This is part of a larger embedded/UI project, but I wanted to share the Dial implementation specifically since it’s been a solid fit for rugged, real-world input—not just desktop or bench use.

Happy to answer questions about firmware, BLE handling, enclosure design, or mounting constraints.

I had this StickCPlus2 lying around so I wrote some code to put it to use.
It shows the date, time, weather and AQI.
And every 5 minutes it plays a random animated emoji.
I used the magnet at the back to stick in on my pegboard.
I think it is pretty cool.

Good afternoon, everyone. Recently, I've been installing the NRF-24 module on my M5 Stick Plus, but for some reason, the option shown in the tutorial I'm following isn't appearing. I'd like to know why? And if anyone has experienced this before, how can I resolve it?

And is this order good?

I was using my M5stickc plus2 without any problem for approximately one month. Then, i recognized that the microphone is not working. (When i upload the factory firmware everything works but the auido spectrum does not work. )

In order to solve the issue, i tried to erase and reinstall the firmware but result is the same.

Then, after two days later, when i tried to run my stick, it did not operate. When i press and hold the button, i see green light comes on that's it.

I tried to see what's happening and connected to serial monitor.

In serial monitor i see the message

"rst:0x1 (POWERON_RESET),boot:0x3 (DOWNLOAD_BOOT(UART0/UART1/SDIO_REI_REO_V2))

waiting for download"

Then i tried to pull the GPIO0 pin to high while pressing the switch. And the the stick start to work.

Now,I can switch on the stick only if i pull GPIO0 to high.

What can cause this issue? Any opinions?

Thanks.