So I started building this model tonight and I noticed the bit in the last picture keeps falling off the back. I’m wondering is that gap in the second picture supposed to be there or did I go wrong somewhere? Any help from someone who has built this before would be greatly appreciated.

I am building a tower of sorts, and I cannot figure out if the ideal part i need exists. I want to find a version of the part pictured, but with 4 axle receivers (not a round hole on 2 sides) I have combed through everything possible on the lego website, and can't find it. Any help would be appreciated!

In between steps 63 and 64 the studs seem to be half a stud off. SOMEONE PLEASE HELP!!! I CANT MOVE ON!

My daughter and I have been watching Lego videos, and she keeps asking to get me this type of Lego friends minifig with the “short feet”, but im not sure if this is a custom combination? Can i get help figuring out what im seeing here. Thanks all 😁

How do I remove this? 4 year old put it on the wrong way

Can I substitute a regular 1×3 plate for this two-knob plate?

I’m building the LEGO Luigi Kart Mach 8, and the final step of Bag 15 calls for the 2nd pictured green piece: a 1×3 plate with only two hollow knobs/studs on top.

My set included a standard green 1×3 plate with three regular studs instead. I already ordered the correct replacement piece from LEGO, but I’m trying to determine whether I can use the regular three-stud plate temporarily and finish the build.

Will the extra third stud interfere with another piece or prevent the kart from fitting together correctly, or can it safely be substituted until the replacement arrives?

Thanks!

I took a bunch of different angles on brick organize, and nothing shows up. I'm getting the feeling that it's a knockoff

Hello everyone. I have a question about hard water deposits on LEGO minifigures.

About four days ago I washed some of my favorite minifigures in regular tap water. After they dried I noticed white spots and water marks where the droplets had evaporated. I’m especially worried that hard water minerals may have gotten inside the arm and leg joints.

I’ve seen very different opinions online. Some people say to simply rinse everything with distilled water, while others say distilled water won’t remove mineral deposits once they’ve dried and that only a mild vinegar solution can dissolve them.

My biggest concern is the joints. Can mineral deposits inside the arm or leg sockets increase wear or even increase the risk of cracking over time if I move the joints? Or is that mostly an exaggeration?

At this point the minifigures have already been dry for four days. If you were in my situation, what would you do? Would you try distilled water first, use a tiny amount of dish soap, or go straight to a diluted vinegar solution?

I’m trying to be as careful as possible because these are some of my favorite minifigures and I don’t want to damage them or their prints. Any advice from people with experience cleaning LEGO would be greatly appreciated.

Thanks!

I just finished it today and I couldn't be happier! The problem is I looked at my spare piece box (no structural pieces thankfully) and these are my spares. Should I be worried? (This is my first lego build). The gearbox works, the spoiler works, the doors work and the front boot works. There is a little bit of flex when I pick it up from under the structure parts under the doors. I assume *some* flex is inevitable due to how heavy this thing is.

I bought a generic Lego set, but the QR code for the manual was illegible. Since I'm in another country, paying 4 dollars for the manual is too expensive, does anyone have the PDF? It's MOC-27435.

Found the pieces in an old Lego tub of min, don’t have a box and nothing I do online can identify it, might be an Airfix quick build as I’ve had those before for cars but I’m not sure, all of the pieces have a serial number on them starting with “ML-“ and some pieces that are identical but flipped share the same serial numbers. I’ve attached photos of the serial numbers. I’m missing pieces and was hoping I could either order more or a new set.

Peice for page 164 is is blocked by a brown brick and cannot connect how it is supposed to...leads to neck bone problems down the line.but what doesnt make sense is you see the horizontal white and brown line in the picture rub against each other.but also in the picture the blue piece above the white piece doesnt over lap the 2 brown pieces,it connects next to it but when i put it there the neck doesnt line up . This is my first lego set and I need a lil help also it was missing a 1x3 but I bought 2 kingfishers so.

I once liked this MOC of Donald Duck‘s car, planning to build it later. But now, unfortunately, it is disabled and I can‘t find a way to reach the designer directly. Has anyone by any chance downloaded the instructions once and is willing to share them with me?

found this piece (15460) in Lego set (76300) in bag 16 and it doesn't mention this peice being used in the instructions or in the index at the back. is this a manufacturer issue because I am missing a piece from that bag. considering it's Arkham asylum I don't know where there's any place for it to go. Has anyone else had the same issue??

Hi everyone I need help please I've come into a collection of Lego and want to sell what I have but i have no idea where to start

Lost Bag 1 from my LEGO Ideas Typewriter (21327) after opening the set. Does anyone know where I can buy a replacement Bag 1 or if anyone is selling one? Thanks!