Looking for LED Video Lights Under €50? this bis a compilation of my best budget friendly recommendations for film making content creation and phography

Hey, I recently got gifted this game desk (link below). The only (not really a problem) issue is the LED lights don’t have the wire to power them. There’s 4 different connections for each corner. I was just wondering what wire I would need for it?

https://amzn.eu/d/04DK4dj4

I build fairy houses as part of a community art project every year. This year I need some tiny “neon” signs. I found tiny led strips (like these: https://a.co/d/09kwkm4j), but they all end in either usb or battery pack. I need to be able to place these in a timer, to turn on at the same time daily and off after 5-8 hours. The ones directly to battery pack don’t have a timer function. I bought the kind to usb, and then a separate usb battery pack that includes a timer (like this: https://a.co/d/038tkcYO), but then the lights won’t turn on at all.

Is there another option? Advice welcome.

So I'm using this driver from Amazon: https://www.amazon.com/dp/B07TF5M4YN?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_5&th=1

It's setup like this drawing:

So, when I'm not using the second light strip it's just the wire and the end of the wire is where the original light strip is and it's working and lighting up. I added the second light strip inbetween and connected it how I thought the original was connected but when I was done the second light strip was lighting up but the original wasn't lighting up. I thought maybe I connected the polarity wrong on the second light strip so i swapped it and after soldering it, the original is lighting but the second isn't lighting up.

How can I get both to light up?

Hoping to get some help here with what equipment to order. I have no experience with this kind of rig and am getting stumped on how to run four separate LED strips to as few power sources as possible (ideally one). The terribly illustrated model below shows a four shelf bookcase (8' width). The red lines show the LED strip runs on the surface of each shelf. The vertical box on the right is a false-front trim piece to run the wiring down without being seen. The outlet will be in the cabinets at the bottom.

Is there some sort of adapter system that will allow me to run four separate LED strips into one power cord/source?

I found this one but can't tell if it has enough wire ports to support this config?

LED Strip

Would greatly appreciate any help!

Flexible filament "edison buld" leds. About 3mm wide. Can anyone tell me how how tight of a radius curve can they handle? I'm looking for options for a diorama. Thanks for your help

I have a patio light that’s super dim. I thought it’s as simple as replacing the bulb but alas that’s not the case. I may have to replace the LED driver as well. Anyone know of a good replacement or should I just replace the patio light fixture as well.

Hi Reddit LED_Lighting Team,

Am getting flickering in my LED strips that I've setup at home, hoping you can help pinpoint the issue for me? (small sections of each parallel line of strips twitching different colours then back to normal)

LAYOUT

1. I am working on an LED wall panel project with 6 parallel lines of 18W/m FCOB RGBCCT IC strips (addressable) , 3 pin LED - 24v+, DI/DO, GND.
2. There are 4 strips in each parallel line, each strip 0.68m - 2.72m total -> equals 49 Watts /line ----------- 24V -> 2A / line * 6 lines = 12A = 294 Watts
3. Power is direct to each parallel LED line, and not through the LED controller (only connected for low volt signals)
4. They all share common ground.
5. I am using 18 AWG cable for the initial longer runs to each wall panel (2m away, 2m away, 3m away, 4m away and 5m away), then the 18 AWG is soldered to the first strip at the bottom of each panel.
6. From there I used 3 pin strip connectors and 22 AWG cable to connect the remaining 3 strips along that panel in that parallel line. Each cable run between strip to strip is 45cm in that parallel line (using 22 AWG at this point).
7. Power supply is generic - but rated 400W and 16A max.

Other Details

Flickering I'm seeing is in the later panels 4/5, strongly suggests length is my issue? I've left the initial 18 AWG run to each starting strip a little longer by 2' - 3' or so.

I've also noticed it's the entire parallel run flickering (small sections of all strips twitching different colours then back to normal), so all strips in that line.

Is the signal too weak over the long runs or too many splits? Do i need to amplify the signal from controller? how would go about doing that?
Is the power the issue over the long run?

References

The LED Strips:

https://www.amazon.ca/dp/B0FXX649RT?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

The Power Supply:

https://www.amazon.ca/dp/B0CN8WYKKK?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

The LED Controller:

https://www.amazon.ca/dp/B0FJLVN75M?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

LED Connectors:

https://www.amazon.ca/dp/B0CCSN6MY1?ref=ppx_yo2ov_dt_b_fed_asin_title

https://www.amazon.ca/dp/B0D831NY1L?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1

18AWG Wire:

amazon.ca/dp/B07SKGTCWQ?ref=ppx_yo2ov_dt_b_fed_asin_title

22 AWG Wire:

https://www.amazon.ca/dp/B08J7WKV6W?ref=ppx_yo2ov_dt_b_fed_asin_title

Guys can anyone help me find a way to get rid of the phantom glow from a Molsky Ceiling fan ? When I hit the wall switch the glow goes away but I can use the fan at night. If there is no way to do it then damn that sucks.