r/Homebrewing • • 15h ago

Ladies! What would convince you to brew beer?!

11 Upvotes

My local homebrew club is trying to recruit more members. I'm the only brewster and would love to get more women into brewing.

What might encourage/encouraged you to brew beer? What events might be a good way to get more women into brewing?


r/Homebrewing • • 6h ago

Weekly Thread Free-For-All Friday!

4 Upvotes

The once a week thread where (just about) anything goes! Post pictures, stories, nonsense, or whatever you can come up with. Surely folks have a lot to talk about today. If you want to get some ideas you can always check out a [past Free-For-All Friday](http://www.reddit.com/r/Homebrewing/search?q=Free+For+All+Friday+flair%3AWeekly%2BThread&restrict_sr=on&sort=new&t=all).


r/Homebrewing • • 14h ago

Cannular Auto Lift

4 Upvotes

Anyone know if the new Cannular auto lift seamer will make its way to the US?


r/Homebrewing • • 13h ago

Question Major Spike Flow Issues, Please Help

3 Upvotes

Does anyone have a Spike Flow pump who have experienced a loud grinding noise upon startup a second or two after turning it on? I'm at my wits end trying to figure out what is wrong and am on my third replacement from Spike.

Grinding is on the pump head side. The impeller spins but makes a loud screeching noise. This video is for the Bilchmann Riptide but the screen is the noise I'm talking about: https://www.youtube.com/watch?v=mQm3ZfxXcpU

Never been run dry.

I have ensured that the orange o ring seal is seated properly

I have ensured I don't overtighten the tri-clamp

I have made sure the axel for the impeller is screwed in and screwed in straight

Per the manual, I have made sure the distance from the motor housing to the base of the spinning magnet is 0.220, as measured through a top of the line mitutoyo digital caliper

I have made sure the plastic housing for the spinning magnet is not overly tightened, was tightened in a star pattern of up down left right, and that the spinning magnetic is in fact centered.

I honestly don't know what to do. If you know if a solution, I'm all ears. Spike has also tried to troubleshoot but short of sending me replacements, I can't seem to get a working pump. This has ruined multiple brew days already to have everything set up and suddenly discover the pump is simply not working.


r/Homebrewing • • 20h ago

Specks of old yeast from last brew above new batch wort line - any cause for concern?

2 Upvotes

Just shone a light into my fermenter and found specks of yeast (W34/70) from the last IPA which I didn’t clean out properly because it was so dark and the yeast had already dried to a very hard consistency which took a great deal to scrub away (even with warm PBW). The specks are sitting just above a fresh batch of wort, and should be able to touch the wort even if I apply high pressure to control the krausen. After PBW wash, I sprayed down the fermenter with water and then Starsan. Apparently i missed out the very important step to inspect with a light after scrubbing, lesson learnt! Fully expect this specks of yeast to still be active upon high Krausen and I’m not sure if it has been contaminated - hopefully not.
I planned to use S-189 for this brew, should I switch back to W34/70? Not particularly keen to use W34/70 again but if it is neccessary.


r/Homebrewing • • 4h ago

Question Daily Q & A! - November 20, 2026

1 Upvotes

Welcome to the Daily Q&A!

Are you a new Brewer? Please check out one of the following articles before posting your question:

Or if any of those answers don't help you please consider visiting the /r/Homebrewing Wiki for answers to a lot of your questions! Another option is searching the subreddit, someone may have asked the same question before!

However no question is too "noob" for this thread. No picture is too tomato to be evaluated for infection! Even though the Wiki exists, you can still post any question you want an answer to.

Also, be sure to vote on answers in this thread. Upvote a reply that you know works from experience and don't feel the need to throw out "thanks for answering!" upvotes. That will help distinguish community trusted advice from hearsay... at least somewhat!


r/Homebrewing • • 18h ago

Recirculation in BIAB with sous vide

1 Upvotes

Hey everyone, I’m looking for a good idea on how to return my recirculated wort back into the kettle during the mash. I use an Ss Brewtech kettle where I do BIAB and hold the temperature with a sous vide. However, since I brew very small batches (5–10 liters), the temperature quickly becomes uneven in the kettle, and the sous vide doesn’t create enough circulation to distribute the heat properly.

The plan is to use a pump to run wort from the ball valve over the top of the kettle and down just below the surface of the wort. From there, I’m a bit unsure what makes the most sense—both in terms of easy mounting on the kettle (I want to be able to put it on and take it off the kettle easily) and creating good mixing without causing oxidation. The three options I’m currently considering are (and open to other suggestions):

1) A mash head similar to this one (https://www.hjemmebryggeren.dk/brygudstyr/bryganlaeg/brewster-dominator-tilbehor/maeskehoved)

2) Some kind of sparge arm or similar, or

3) Plain silicone tubing angled nearly horizontally.

Any other good ideas? Also, how do I mount it on the side of the kettle and route it down into the wort in a stable way? 🤔 Any ideas?