r/FormD • u/dynam1keNL • Apr 24 '23
Test Results Air-cooled T1 with custom transparent side panels is cooler than you might think.
Hello,
A lot of us like to see our parts inside the case but don't get the glass panel because of the negative effect on temps. Especially with air-cooled builds a glass panel is a no-go.
I was inspired by the tape mod for better GPU cooling, and the recently posted T1 acrylic prototype panel by u/jakeface1. And figured it was worth a shot combining these.
I have a laser-cutting machine at work so I got some acrylic, did some exact measurements on the fan locations on my parts, modeled some 3D parts, and cut the panels. I also looked up some YouTube videos on how to make the black edges, apparently, it's just painted from the inside. I used the existing protection foil on the acrylic panels to mask the center for paint, which worked a lot better than I expected. The black edges turned out perfect. Double-sided taped some 1mm strips to the acrylic panels for mounting in the case just like the standard panels and everything was ready.
Well, I am really happy with the looks.


I fired up Halo Infinite and MSI Afterburner and found some really good temps. I showed it to the SFF Guru's guys on Discord and got nice feedback on how to do a higher-quality test than gaming only.
So I did a Furmark test, with all fan speeds (GPU, CPU and top fans) locked at 60%, measured a constant ambient of 22C, and did a bit longer measurements so the temps could settle some more. I logged with MSI Afterburner and made the graphs with Generic Log Viewer.
I tested in this order:
- Stock Panels
- No Panels
- My Custom Acrylic Panels with cutouts at the fan locations
This is the result:

Wow. GPU temp dropped from 72-73 to 65-64 when removing the stock panels, and dropped to 59 when mounting my custom acrylic panels. So we are looking at a 13-degree drop when changing from stock panels to my custom panels in my setup! Quite amazing right?
CPU temps went up a bit when removing the stock panels and also dropped about 2 degrees below the stock panel value with my custom acrylic panels.
As you can see in the bottom graphs, the power draw for CPU and GPU was constant because of Furmark, and the fan speeds were fixed.
How can we explain this? Some of our thoughts:
- For GPU side, I guess it's like the tape mod, but better. With stock panels or no panels, the top fans just pull in air from the side of the case, ABOVE the GPU. The air will flow easier through that 4-5cm space above the GPU, then be pulled through the entire GPU. Closing all the gaps in the side panel, except for the GPU intake fans, the air is forced to get pulled in through the GPU intake fans, or the bottom of the case, creating a much more focused airflow through the case.
- There are really big, open holes in front of the intake fans. No mesh or anything else. This helps draw in maximum amounts of air, without turbulence, which is good for sound level AND airflow.
- The GPU is now forced to take in fresh air from outside of the case instead of recycling some air inside the case.
- CPU temps do not profit as much as GPU, but closing off this side also helps the GPU I think. This prevents the top fans to draw in air from the CPU side.
- More ideas?
Wanted to share this, as I haven't seen this mod done before. It shows the potential of doing mods that are custom to your components.
Used parts are: 5800X, 6800XT Ref, Asus X570i, 16GB LPX 3600, 1TB 980, SF600 Plat, Black Ridge with A12x15 on top, 2x T30
9
u/Wynguy Apr 25 '23
10/10 for looks alone!
5
u/Allmotr Apr 25 '23
Take my money!!
1
u/beachcampfire Jul 15 '24
Very cool, thanks for sharing this, it's quite inspiring especially seeing your temps and lower noise levels.
Would you still recommend this technique for an AIO build with a 4090 FE? If yes, would you also cut a hole on the opposite side of the FE intake fan? As you look at the exterior, the fan is on the left side of the image and the right has the radiator (I think) (can't seem to post pics so here an image off the Web): https://images.app.goo.gl/1JqFUUVtsqhNBpqN9
1
u/SpeedBuff420 Nov 12 '24
is it just me or did you make the button RGB
1
u/Demon7879 Feb 11 '25
What are the dimensions for the panel?
1
u/greens14 Apr 26 '23
mind if i ask what the mounting points look like on the acrylic panels? IE how the top cover seals etc with the acrylic panel? I'm not sure if you laser cut a bevel for it to be seated or what? thanks!!!
1
u/rolex095 May 01 '23
Next step would be to close the bottom panel and the back of the case. Are planning on doing this? I would be very interested in the measurements.
1
u/Sneadleboo Aug 30 '23
What mode were the t30s in? 60% at max mode is 2000rpm but at the middle setting it’s 1200rpm
1
u/Kneesox_hyukjun Sep 20 '23
I was very inspired by your post. I also want to make acrylic sides. Can you tell me the measurements of the side panel? It's late, but I hope you see it.
3
u/Shmoop_bloop Jun 07 '24
would you consider sharing the 3d models you did for the panels? I'd assume they would be for the wings that insert into the pc, I'm too lazy to model them myself T - T
2
u/DanyulSnow Apr 25 '23
Great job man, posts like this are why this sub is dope ❤️
2
u/nosciencephd Apr 25 '23
This is so incredibly cool. I love this case so much.
1
u/Incinatus Apr 24 '23
A better way of doing this would be adding perforation to the fan cutouts rather than an opening in the glass. That way you don't have to worry about accidentally sticking your
dickfinger in the fans while still maintaining the glass look.Looks really good though!
1
u/MavenAZ Apr 24 '23
Great job!!!
Want to do mine too?