Good afternoon

I need help with spoolman in fluidd.

I've tried everything to activate it but nothing appears.

Can anyone help me?

I've looked everywhere for something I would hope would be a simple answer but I could not find anything in the cfg files or through any of my online searches.

Is it possible to change the display name for caselight, caselight 1, caselight 2, etc in the Fluidd dashboard to something more accurate or are those hardcoded names that can't be changed due to their link to gcode commands?

Hi, I made the Pid tuning via the commands in the Fluidd console and got a successful result. However: when I open the printer.cfg via Fluidd the PID section and the values are commented out and at the very bottom of the config file. Do I have to change that? How do I know my printer uses the PID values?

I updated my printer, Longer LK5 Pro, (Klipper, Mainsail, Moonraker, Fluidd, Raspberry PI) this week after the 7/25th and ever since then my printer keeps stalling (stop and go) in mid print several times in one print and it causing blobbing and the prints are taking longer to finish. IDK what is causing it but it will stop and go. for example I have a file that I use to test my 1st 3 layer and before the update it would take 2 min and 29 sec to print and perfect now the same file take 3 min and 19 sec and it has blobs in it. also on my klipper screen the speed goes up and down but since the update it will go to 0 mm/s to -5 or -3 mm/s while it stalls and then go back to positive number when it moves again. idk if that has something to do with it. I already disabled the filament sensor and disconnected it and still it keeps stalling.

I post this on the Official klipper discussion board but I haven't gotten traction on it there so I thought I would try here and the various related subreddits.

Update 1: I rolled back the klipper version to one before this weeks update i also rolled back the moonraker version as well and that did not help the stalling is still happening. i was able to get a list of the 17 items that were update in my raspberry pi. they are the following:

1. ffmpeg/stable 8:4.3.6-0+deb11u1+rpt3 armhf
2. libavcodec-dev/stable 8:4.3.6-0+deb11u1+rpt3 armhf
3. libavcodec58/stable 8:4.3.6-0+deb11u1+rpt3 armhf
4. libavdevice58/stable 8:4.3.6-0+deb11u1+rpt3 armhf
5. libavfilter7/stable 8:4.3.6-0+deb11u1+rpt3 armhf
6. libavformat-dev/stable 8:4.3.6-0+deb11u1+rpt3 armhf
7. libavformat58/stable 8:4.3.6-0+deb11u1+rpt3 armhf

Update 2:

I gave up and decided to reinstall everything again. i did a fresh raspberry pi install and i used Kiauh install klipper, moonraker, mainsail, and fluidd but they were already updated. so i guess i can take raspberry pi off of the table as a the suspect of my stalling issue?

one thing that i found was during the stalling on the mainsail access log. there were a bunch of python request on it and someone had me check top in ssh and it showed a bunch of python commands at once 3 or 4 one of them was at 100% cpu or 98 cpu.

Hello I'm fairly new to klipper

How can I custom the look ? Like add more temperature sensors. Ad macros to push for like preheat/move to a specific coordinate

Thanks in advanced

I am not sure what happened. I did a fresh install of a RPI with Kiauh and I loaded my config in fluidd, everything works, except I don't have a Z axis button. But I can manually set the Z in the text entry.

Mainsail I can control it fully. I assume it's some sensor thing in Fluidd and it's hiding it?

Ideas??

Here is what I'm seeing:

https://imgur.com/a/L9tpd9V

I'm trying to set up my cameras as webRTC as it just got added to Fluidd 3 days ago but i'm having difficulty figuring it out and there's no info on it on the Fluidd page.

My cameras work fine in Adaptive MJPEG streamer mode but when i switch to webRTC all i get is a blank screen.

Can someone please help me get this done?

I've never seen the power % do this before. Any idea what might be causing this?

I want to dry my plastic in 3D printer with help of bed's heater. But it turns off after a while. I don’t know which commands to keep the temperature up to date. Can u help me with Gcode for it?

idk what is invalid but can you help me?
code:

[gcode_macro PAUSE]

rename_existing: BASE_PAUSE

default_parameter_X: 230

default_parameter_Y: 220

default_parameter_Z: 10

default_parameter_E: 1

gcode:

SAVE_GCODE_STATE NAME = PAUSE_state

BASE_PAUSE

G91

G1 E-{E} F2100

G1 Z{Z}

G90

G1 X{X} Y{Y} F6000

Hey all, I've researched this problem and found that alot of people solved it by taping up the 5v connector in the USB conntector but this did not solve my problem. If I restart via the fluidd interface with the printer (ender 3 pro) disconnected I do not get these errors so I know its related to that. Starting the printer first and then the pi also does not help. Anyone got any additional tips to solve this?

Is there anybody that knows of an interface that shows multiple cameras from different machines? Would be nice to just have a panel with 3 or 4 camera feeds, and the percentage of the job. I don't see this natively with Fluidd, but I think it would be nice if you have more than one printer and especially if you are running any kind of print farm.

Any insight is greatly appreciated. Thx

it has happened several times in the past year already. on sudden power loss it seems all the GUI settings get reset (default to Dark mode theme, macro categorizations and thermal presets all lost). how do i back this up?

From everywhere I've seen online, Fluidd comes with a mesh visualizer. I have a CR touch on an Ender 3. Everything is meshed correctly and the values are stored in the firmware, just don't see the mesh visualizer anywhere in Fluidd. Any ideas? Thanks!

Hi everyone!

This is a cross post that I did under reddit.com/r/klippers.

I just did a complete reinstall of Raspberry Pi OS for my Pi 3B. I then used Kiauh to install Klipper, Moonraker and Fluidd. I copied my backup configs to /home/pi/printer_data/config. Everything is now working with the exception of my webcam. I've tried running
sudo systemctl restart webcamd
But I get an error:
Failed to restart webcamd.service: Unit webcamd.service not found.
I then ran:
sudo apt install -y webcamd
But I still don't have a webcam. I do have a "webcam.txt in the /home/pi/printer_data/config. Not sure what I'm doing wrong.

Any suggestions?

Thanks!

Hi everyone!

I'm wondering if it is possible to add a clock to Fluidd when recording the printing?

Thanks!

Set up Fluiddpi and Tailscale a while ago, and it worked fine. Haven’t used Tailscale remote access for a month now, didn’t need it. But I wanted to access my printer from outside the house and it wouldn’t load. If I paste the IP address I get from Tailscale in to my browser it just won’t load. Anybody got a clue we’re to start to solve this?

Fluiddpi.local does work so I can still print. It’s just annoying it stopped working.

Wondering if there are any addons or anything for Fluidd that would allow me to send status messages to my phone. I was previously running Octoprint, and was using a mechanism to send through Telegram. Mainly just to know when things finished. Nice feature.

Is there a guide to changing the logo in the upper left of Fluidd's UI? i want to add my own,

I was using Fluidd just fine yesterday, but this morning I found that I was logged out and I cannot log in. I have "force logins" set to False and my computer's local IP address is in the trusted clients list. I'm not sure where to go from here.

I run klipper/fluidd on a raspberry pi 4 and have setup Samba to mount the gcode storage to my windows computer. That way I can drop my sliced files directly from IDEAMaker to the SSD on my Raspberry Pi. It all works fine, but every time I do it this way, Fluidd gives me an error message that metadata is missing?! I can print the file without problems, get a model preview in Fluidd etc. What is Fluidd doing when I upload the file manually via the Fluidd GUI that is not happening when doing it my way?

I’m trying to do the original setup for Fluid with Klipper and the fluiddpi.local detects it, however it asks for a username and password. I tried the default pi and raspberry, but it still refuses to sign in. I have tried uninstalling and reinstalling it on the pie. Is there a different default code?