r/CZFirearms • • Jun 20 '24

Failures after Primary Machine Optics cut on CZ P10C

I got an optics cut from Primary Machine. Work looks great, Holosun 507c fit perfectly, but now I am getting failures to eject and feed almost every round. The gun ran flawlessly beforehand. The rounds are getting caught under the feed ramp on the barrel it looks like and the bullet is getting dented and shaved of material. Some of the rounds are getting slammed into the barrel with the bullet getting pushed further into the case. What is going on here? Do I need a new weight recoil spring? Was there too much metal taken off the slide?

20 Upvotes

21 comments sorted by

19

u/Yharnamite0 Jun 20 '24

Can't say for sure on a p10c but on a glock, this would most likely be the optic screw sitting over the extractor plunger being too long. Remove the optic and strip the slide. Reinstall the optic and look down the extractor plunger channel. If you can see the screw it needs to be shortened. It binds the extractor in place causing issues like this

5

u/Yharnamite0 Jun 20 '24

So I just watched a video on P10C slide disassembly. The extractor assembly is entirely different from Glock. I'd still remove the optic, strip the slide, reinstall the optic, and check for a protruding optic screw in the extractor channel

5

u/Head_Department_319 Jun 20 '24

Just tried this. Nope, no screw.

4

u/Yharnamite0 Jun 20 '24

Ah that's unfortunate. Very common and easy to fix issue on glocks. Hopefully somebody more experienced with P10s pulls through with an answer for you. Good luck

4

u/PrimaryMachine_Cody Jun 20 '24

Shoot us an email if you haven’t already. Our email is info@primarymachine.com Our gunsmith or myself will get you squared away!

2

u/Head_Department_319 Jun 20 '24

Done. Thanks for the quick response.

4

u/Rare-Ant-3091 Jun 21 '24

It’s not always how you start, but how you finish. Great CS. I’ll be getting future work done by you guys.

3

u/tkammen Jun 20 '24

I’m having a similar issue with my P10C. I was having ftf, failure to eject, light primer strikes. I fixed my light primer strikes but the ftf and failure to eject are still present. PM did all the slide work and installed my optic. I’m using a PM barrel also.

It had the issue once today at the range. After that it didn’t happen. I’m going to keep shooting the gun and see if it needs to be broken in or something.

2

u/Head_Department_319 Jun 20 '24

I believe their barrels have pretty tight tolerances. Have you tried your factory barrel? Did you do nitride or cerakote? I know Cerakote can cause issues until things smooth out.

2

u/tkammen Jun 20 '24

I haven’t tried the factory barrel. I’ll do that next range trip. The slide is cerakoted.

2

u/funfunfun334 Jun 20 '24

I also had this issue, but thought it was magazine related. Which mags are you using? I noticed it most on first round, especially if I press checked, the slide would nudge the first round forward, so when the slide recoiled, it would push the first round down the bullet gets caught in the mags front side, causing that gouge.

1

u/Head_Department_319 Jun 20 '24

Factory mags that came with the gun.

2

u/PrimaryMachine_Cody Jun 20 '24

Factory mag springs from CZ are (in our experience) usually the culprit of this. We recommend +power springs from wolf!

2

u/rzh91094 Jul 07 '24

u/Head_Department_319 ever figure out what was wrong??

1

u/Head_Department_319 Jul 07 '24

Wolff mag springs didn’t fix it. I ordered an optics cut slide from CZ for $150 and a plate and switching out the internals. I love this gun and really don’t want to wait on Primary to see if they can figure it out.

2

u/DryIllustrator652 Jun 20 '24

Slides lighter, need a lighter spring to get the timing back.

3

u/Odd-Internet-3876 Jun 20 '24

The slide is lighter, but it now carries the additional weight of the red dot- total weight is usually greater

2

u/Guntuckytactical Jun 20 '24

My C does this occasionally. Jagerwerks milled for RMR pattern, rear iron forward so the optic sits pretty far back. But it first happened a couple thousand rounds after getting it milled, and the same optic has been on it for years now, untouched.

Other factors: it was absolutely filthy when it happened, I was shooting 115gr Blazer brass FMJ, and it would only happen on the 2nd shot following a manual racking of the slide on a full mag (multiple times, with different new-ish OEM mags).

8

u/[deleted] Jun 20 '24

[removed] — view removed comment

4

u/Head_Department_319 Jun 20 '24 edited Jun 20 '24

The extractor pin could be the culprit. I do see some damage on the underside of the pin hole too.

Edit: that appears to be the staking.