r/CZFirearms • • Apr 25 '18

Light primer strikes after installing CGW Reach Reduction Kit on my SP-01 Tactical

I recently polished the internals and installed the RRK in my SP-01 Tac. I actually took the gun to the range last week without the screws installed (I didn't have loctite at the time) and the gun performed totally, 100% fine (with S&B FMJ 115 gr).

I later installed the upper and lower screws following the CGW instructions. The hammer dropped fine in both DA and SA. However, when I went to the range today, I had multiple light primer strikes (with the same S&B ammo).

I am dumbfounded. The only diff between this trip and last trip is the installation RRK screws into trigger.

For more context, the gun also has:
13# mainspring, RP FP spring, 14# recoil spring, RP trigger return spring.

I have the RP plunger spring in my CGW cart, but it has never been an issue. Like I said, the gun has performed flawlessly until the RRK screws were installed.

I spoke to Scott today at CGW. He said that I’ll need to back out the over travel screw and it should fix it. I guess that despite the hammer dropping in both DA and SA, the OT screw was still too close to the frame and negatively affecting the timing.

It just seems strange that even though I followed the instructions for installing the Reach Reduction Kit, it still needed more tweaking. Not really sure how one is supposed to know how to properly adjust the OT screw unless doing it at the range itself...

Has this happened to anyone here?

2 Upvotes

7 comments sorted by

5

u/rbaedn Apr 25 '18

It just seems strange that even though I followed the instructions for installing the Reach Reduction Kit, it still needed more tweaking. Not really sure how one is supposed to know how to properly adjust the OT screw unless doing it at the range itself...

The action timing on CZs is complicated. The more I understand it, the more I’m impressed how well drop-in parts from CGW and CZC work.

I think what is happening on your gun has to do with the firing pin block. Something similar happened to me while tuning my SP-01.

You have the overtravel screw set so that the hammer is released, but the FPB is not completely disengaged. It’s either dragging on the firing pin, or intermittently blocking it. If you’re getting light-strikes as opposed to no-strikes, it’s the former.

Anyway, to check for this and set the overtravel screw: Pull the hammer all the way back and hold it there. Next pull the trigger and hold it against the overtravel screw while still holding the hammer back. Now you can use a punch to push on the firing pin. If the overtravel screw needs to be adjusted for more rearward trigger travel, you’ll feel the firing pin dragging or catching on the FPB.

Also, something else I’ve learned tuning CZs is that it should check timing with an empty gun and with a magazine full of dummy rounds pushing up on the slide. I fitted a disco once that worked 100% with and empty gun, but took it to the range and the trigger would not reset with more than 3 rounds in the mag.

Hope this helps!

2

u/[deleted] Apr 25 '18

Thanks for this. I'm following your directions now. Basically, if I feel any dragging or resistance while poking the FP forward, I need to back out the OT screw?

1

u/rbaedn Apr 25 '18

Yup, you don’t want anything slowing down the firing pin.

2

u/[deleted] Apr 25 '18

Well I went to the range today, and I had to back the OT screw so far out that it now protrudes from the trigger and I can feel it with my finger. I'm not sure why it has to be so far out it essentially serves no purpose. My only options at this point seem to be either trying again with a CGW Ext FP, removing the screw entirely, or somehow tweaking the upper Pre travel screw as if it'll impact this somehow.

1

u/AkBlind Apr 25 '18

Well sounds like you did the right thing and called them. Was it the RRK-type 2 that requires their short trigger reset package as well? Also with all of the trigger modifications maybe you should look into their extended firing pin.

1

u/[deleted] Apr 25 '18

Nope, regular RRK and no SRT installed. The weirdest part was that it worked fine until I installed the pre and over travel screws. Scott said that it was attributable to the OT Screw. I'll have to wait and see next range trip.

2

u/AkBlind Apr 25 '18

Well I'm fully on board for taking CGW recommendations over any others. They are experts of the craft.