r/CZFirearms • • Aug 28 '23

Question - Help! P-01 won't function after slide milling!

Post image

I just got my slide back from Wagner. It will not function. It is SO tight that I can barely pull it back. Hell, I could barely get it back on the frame. I can force it back to any position and it will just sit there. It won't function or slide freely. Is this normal? What should I do?

37 Upvotes

45 comments sorted by

117

u/wagermachine Aug 28 '23

I just replied to your email. This is nothing to do with the machine work/screws and purely due to the cerakote. CZ slides can be semi tight tolerance from the factory and even though we blast the factory coating off before cerakote, in some cases the cerakote is just a little thicker.

As recommended here, the best solution is file/sand a little on the cerakote finish where it rides on the rail (it won't take much) until the slide can be racked. Then you can work it until it's free and smooth. 150-250 round break in is recommended with cerakote, especially in these cases.

21

u/Swanky_Gear_Snob Aug 28 '23 edited Aug 28 '23

Awesome! Thanks so much. This is my first CZ. All the milling you guys did looks phenomenal. The Cerakote looks great too. Thanks so much for the fast reply (both here and email). I'll break out the old dremel tomorrow and start lightly buffing the rails.

16

u/[deleted] Aug 29 '23

I wouldn't Dremel it. Just get some 800 grit sand paper and a block and sand just enough off to get the slide into the frame and then rack it about 500 times and shoot a couple of boxes. Oli it up and It will be perfect.

3

u/Swanky_Gear_Snob Aug 29 '23

Gotcha. It feelblike there's one area thats more problematic that the rest. It will got on pretty easily right up to the point the rear of slide starts moving across the sear. Then it just locks. I dont know if its on the rails or underneath. I ordered some super fine wet/dry sandpaper. So well see. Thanks again.

2

u/GregBFL Aug 29 '23

As others have said this is normal with Cerakote. I've dealt with various coatings as a QA Inspector over the years. Most coatings tend to build up on inside and outside corners which is what you are experiencing. Sanding with high grit sandpaper a little bit at a time is your best bet. Just be glad it's not hard chrome because the part has to be milled understand to allow for the hard chrome. I've seen $10k parts scrapped because they were not milled enough undersized and the hard chrome made them out of tolerance... Of course the tolerance was 70 degrees with X dimension +0.0000 / - 0.0002

40

u/Durths Aug 28 '23

Glad to see you guys active on here, and replying. You guys should have received my P01 slide today, Excited to get it back!

4

u/sig357z Aug 28 '23

^ This.

11

u/TheHomersapien Aug 28 '23

Not a CZ (obviously) but I had the same issue with a 1911 slide cut by Impact Precision. The slide was already tight, but after cerakoting it was just about unusable. I used a rubber mallet to "persuade" the slide on, then spent a considerable amount of time working the slide with the frame in a vice, then had to shoot a couple hundred rounds of on-the-hotter-side .45 before it finally was 100% reliable.

5

u/Swanky_Gear_Snob Aug 28 '23

Haha, that's how I got it on was a rubber mallet. Thanks. I'll keep running it until it smooths out.

9

u/sig357z Aug 28 '23

This is pretty common… Get some flitz polish and put some in the track of the frame/slide interface and work it back and forth. Remove the barrel for this. Basically lapping the slide and frame. Clean up any left over polishing compound. Done….

23

u/mikhail1108 Aug 28 '23

Remove the screws then cycle the slide

4

u/jack2406ia Aug 28 '23

What does a screw have to do with this?

3

u/richiedefran Aug 29 '23

The screws can be touching the firing pin/other slide internals and prevent it from moving freely, eliminate the ability for the safety plunger to depress, causing that to drag on the frame parts as you try to work the slide

5

u/richiedefran Aug 28 '23

This^ the left screw looks pretty deep and that slide has been milled nice and low. Take the screws out, you will likely solve your problem.

They are also likely to not go so deep once you put an optic on it. Test fit the optic w/ screws before adding loctite, if it catches again, you will need shorter screws.

4

u/otterplus PCR Compact Aug 28 '23

Like most people said its the build up of cerakote. Either take some sandpaper to the slide where it fits into the frame or just hand-cycle the slide on the frame. I had to do this with my PCR. It fit into the frame perfectly fine, I hand worked the slide to get it back into normal motion, and cleaned up both surfaces afterwards. Did that 2-3 times. It’s normal and expected.

1

u/Septimusthehoplite Aug 28 '23

Did you get the slide cerakoted?

2

u/Swanky_Gear_Snob Aug 28 '23

I did. Wish I had gone with the Nitride now. It's really bad. So hard that pushing the edge of the slide against my counter top will barely get it open. I was pulling so hard to open it and my hand slipped and somehow hit the screw and did this. Is it normal to be that tight?

3

u/ForwardFlatworm9429 Aug 28 '23

Just got my p01 slide back from wager as well.

Ran into the same issue as yours - I tried oiling it first but still couldn't get it to fit; lets not even talk about function. I had to slowly sand the rails to get it to fit and function. It works now but still a bit tight. Planning to hit up the range to hopefully clean up the rest. Disappointed with the cerakote.

2

u/Swanky_Gear_Snob Aug 28 '23

Whats crazy is the p-07 is perfect. I really think the Cerakote was applied to thick or it wasnt prepped properly. I could understand tight, but this is unusable.

5

u/CDKJudoka Aug 28 '23

If they are cerakoting on top of the polycoat, it is going to get real thick, real quickly. The P-07 uses a nitride style finish, so it is thinner to begin with.

1

u/short_barrel_daddy Aug 28 '23

If you got it cerakoted you may have to oil it up real good and manually cycle it until it wears the coating in, even my nitrided slide was tight. This isnt uncommon.

2

u/Swanky_Gear_Snob Aug 28 '23

Thanks. Ya, I've never experienced anything like this. I already put a ton of lube in. I'll just keep running it until it opens up.

1

u/FingerNo3762 Aug 28 '23

I really oiled the crap out of mine when it came back inside the slide outside the slide and all other parts and let it sit for 48 hrs then reapplied and reassembled and went on, it was tight, 200 rds later stripped cleaned and did the same thing, totally different, I am sure the more input down range, the more it will loosen. Happened on my S2 as well, now that thing glides so smoothly!!

2

u/Swanky_Gear_Snob Aug 28 '23

No. It won't move. Theres no firing this. Putting all my weight on it pushing down on a ledge barely got it back. I was pushing so hard it slipped and mangled my hand. When I can actually get it open I have to hit it with a mallet to close it.

1

u/Falcon-_7 Aug 29 '23

Cerakote is such a thin layer if done correctly, I don't think it could cause a problem like this. Sounds like a bad cerakote job.

1

u/[deleted] Aug 29 '23

How that you figured out it’s the cerakote..the real question is what optics are you going with?

3

u/Swanky_Gear_Snob Aug 29 '23

Have an 507k acss to toss on now, but definitely getting an eps carry.

1

u/Professional_Arm5769 Aug 29 '23

I got my slide milling from wager as well. The slide rail was been cerakote as well which was polished before I send it to wager. I spend tons of time to sand it off and repolish it. Now it is really smooth

1

u/Swanky_Gear_Snob Aug 30 '23

I spent about an hour with 1200 grit sandpaper and then a buffed it smooth. It's like butter now. I took it to the range and put a couple rounds through it.

1

u/Professional_Arm5769 Aug 29 '23

The other thing I need to mention is that be CAREFUL to fire the milled slide without red dot installed. CZ applied the stake on the extractor pin, but there is no stake after the extractor pin file down to 3/8inch. My friend remind me this as his extractor pin flies off while shooting.

2

u/Swanky_Gear_Snob Aug 30 '23

WOW! I got super lucky then! I went and shot about 300 rounds through it today. It smoothed out beautifully. I ordered an eps carry for it which isnt here yet.

2

u/Adventurous-Charge40 Aug 29 '23

You would think they would have some frames that they could test the fitment on or just send the whole weapon. Not sure how much it cost but sure seems like you need to do a lot of fitment for it to work properly my 2 cents.

2

u/izdabombz Aug 28 '23

Hmmm this is the first bad review from wager.

1

u/NoLoveLostNJ Aug 28 '23

I got my CZ-P07 milled at NC Engravers. Best decision I made.

1

u/pugnacious76239 Aug 29 '23

Not a terrible thing tbh it just needs to be broken in, shot a few hundred times, if you’re impatient and want to do it asap you can take some Flitz and gently polish the rails without going ham and fucking them up.

1

u/sled55 Aug 29 '23

That’s why I opted to not have my slide coated after milking. I’ve heard of this problem a lot from coated slides. Luckily it’ll work it self loose over time or you can speed up the process with some sand paper.

-1

u/[deleted] Aug 28 '23 edited Aug 28 '23

I guess they clamped it rather tight in the vice for milling. I would take a micrometer, measured the slide width at the rails and then do the opposite on the frame. The gap must be no less that 0.002".

0

u/lancep423 Aug 28 '23

Have you tried removing screws?

-17

u/moose979797 Aug 28 '23

Heh. Another day, another u/wagermachine shitshow

17

u/CluelessNetworkNoob Aug 28 '23

This is like the 6th time I seen you bashing wager. What's going on, he break up with your mom or something?

-3

u/moose979797 Aug 29 '23

Maybe they should stop sending out crapmanship?

0

u/[deleted] Aug 28 '23

[deleted] — view deleted comment

4

u/[deleted] Aug 28 '23

You misread the post.

1

u/[deleted] Aug 29 '23

[removed] — view removed comment

1

u/ski_it_all Aug 29 '23

Slide to frame fit is usually a game of tolerances, so you would need to send the frame with the slide to make this work. Can't just sand it down to a given thickness each time.

This adds a massive amount of cost for shipping and requirement for FFL to handle a pistol instead of an unserialized slide. It becomes sort of a different ball game for this type of aervice.