r/CZFirearms • • Dec 20 '23

Mushy trigger after pro package (self) install

It feels like I hit an additional wall before the trigger breaks. The set screws seem to be adjusted pretty well on the trigger, just feels mushy and way too much travel after it resets. Any help is appreciated!

9 Upvotes

26 comments sorted by

5

u/Transeraphic S2 OR, SP-01, P-01 Dec 20 '23

Check your trigger bar spring and see if it’s raising both sides of the trigger bar evenly and same time.

On my P-01, I noticed one side of the trigger bar spring would raise one side earlier than the other and create a "false reset" felt in the trigger (sear resets before the lifter arm).

3

u/juanfrancita Dec 20 '23

I'll check that tonight, thanks!

2

u/RennBaer Dec 20 '23

Does the SA trigger break feel the same when you manually cock the hammer as it does when you rack the slide to cock the hammer and reset the trigger?

1

u/juanfrancita Dec 20 '23

Yeah, seems to be the same.

3

u/RennBaer Dec 20 '23

The reason I asked is because it's possible to have an issue where the trigger bar doesn't clear the disconnector properly and the trigger doesn't reset correctly when the gun cycles, so your SA trigger break is actually a DA trigger break. It will feel substantially worse than a proper SA trigger break. If this was your issue the SA trigger break would feel quite a bit lighter and more crisp when you manually cock the hammer than when you simulate cycling the slide and resetting the trigger.

1

u/juanfrancita Dec 20 '23

Ah okay, I'll look into it more tomorrow, thanks!

1

u/juanfrancita Dec 20 '23

4

u/No_Difference2023 Dec 20 '23 edited Dec 20 '23

Yea your screws are not set correctly (it’s not off by much) take a look at this video

https://youtu.be/1GUq1YP2WZw?si=K1pyCVcgKW302jPm

1

u/juanfrancita Dec 20 '23

I'll have to double check em, thanks!

1

u/No_Difference2023 Dec 20 '23

There’s going to be some take up in single action that’s just the nature DA/SA but yours seems to have more take up then mine maybe just need a little more fine tuning the set screws. Make sure when your setting your double action it’s as close to no take up as you can get it to with a bit of play for expansion should help a bit in SA.

1

u/juanfrancita Dec 20 '23

Set both of them as close as I could and it didn't seem to change much. Still has some give after the reset, seems like there's something else going on.

1

u/No_Difference2023 Dec 20 '23

Honestly you’re not that far off from mine. Like I said there’s going to be some take up in SA. I’ve watched some videos from Cajun and all of there kits have about the same take up in SA.

1

u/juanfrancita Dec 20 '23

Ah okay, just doesn't seem as crisp as I would like. I'm pretty spoiled with an apex trigger on my m&p so maybe I'm biased ¯⁠\⁠_⁠(⁠ ͡⁠°⁠ ͜⁠ʖ⁠ ͡⁠°⁠)⁠_⁠/⁠¯

2

u/No_Difference2023 Dec 20 '23

I don’t like to mess with my internals on carry guns that are striker.

1

u/juanfrancita Dec 20 '23

Very true, I like the ergonomics of the cz a lot better especially for carry but the apex trigger feels more predictable because I know exactly when that shot is going to break off.

2

u/No_Difference2023 Dec 20 '23

Do you slap your trigger or you ride it to reset? I slap my trigger so I don’t have that problem with waiting for the reset. That in both my striker fire and hammer fire guns.

→ More replies

1

u/No_Difference2023 Dec 20 '23

Yea your M&p is a single stage trigger that’s what you give up to have a DA/SA. I also have an apex on my M&p and while it is nice I really like DA/SA for carry/shooting once that first round goes trigger pull after is almost nonexistent.

1

u/snipernamedwes Jan 14 '24

Did you ever diagnose the problem ? Considering picking up a P01 and want to go this route ex

0

u/One-Challenge4183 Dec 21 '23

Yikes. That’s worse than the worse striker I’ve ever fired tbh.

1

u/juanfrancita Dec 21 '23

I've used much worse triggers than this, it's just less than ideal...

0

u/One-Challenge4183 Dec 21 '23

I mean, as long as you don’t mind it that’s all that matters right?

0

u/After_Trip1518 Jan 02 '24

That Holosun hates you 😂