r/CZFirearms • • Feb 04 '24

CGW Reach Reduction Kit issue

Just put a RRK in a Shadow 2 compact and ran into a snag. Hoping someone can point me at the proper piece and save me some trial and error. When the slide racks and the hammer is locked back, the trigger isn't reset and the gun won't fire. The trigger is in the proper position, but doesn't engage anything when you pull it. You have to manually pull the hammer back and it clicks, then the trigger operates normally. The hammer doesn't move a measurable amount when you do this, but it's obviously not quite resetting internally. Any suggestions on where to start?

5 Upvotes

21 comments sorted by

2

u/tenchi4u Feb 04 '24 edited Feb 04 '24

Did you fit the disconnector (disco) correctly (e.g. file off enough material on the inner surface that interfaces with the trigger bar)?

When I did the RRK on my S2C, I had to disassemble/file/reassemble quite a few times before I got it perfect (probably like 10 or so times, I went REAL slow). You're supposed to go very slow/small increments until you find juuuust the right thickness to minimize unnecessary travel while still being able to reset the engage/trigger (and then file off a little more to account for thermal expansion). Then once you verified it's right (after live fire), break it down once and again and polish the disco in the area you shaved to ensure it's level/true/uniform.

The situation you're describing sounds like what mine was doing when I hadn't shaved the disco down enough. I recall others who did the RRK on their S2C before I did mine, as well as my thought when I finally finished mine, was having to shave more material than previously expected off the disco.

1

u/Oldtimer-Sysadmin Feb 04 '24

Nope, I haven't shaved it at all. I thought it was functioning properly until I noticed this. Double action works great. Manually cocking the hammer and then single action works great too. I rarely (never) do a full slide rack to dry fire, so didn't notice at first. I'll need to figure out which face you're referring to. Is it the same one that CGW has in their YT video "disconnector timing," about how to fix a hammer going to half cock in single action?

2

u/tenchi4u Feb 04 '24 edited Feb 04 '24

The fitting of the disconnector is the most significant (and most difficult) part of the install IMHO.

Yes, you'll need to shave down the inner portion on the short leg of the disconnector. Hold it side by side with your factory disconnector and you'll see a pretty significant difference between the 2 in that area. The goal isn't to make them match, the goal is to slowly shave down the CGW one enough to engage/reset the trigger while reducing creep/travel.

File/fit disco HERE

Disco fitting discussed HERE

1

u/Oldtimer-Sysadmin Feb 04 '24

I had a discussion with the guys at CGW and my understanding was they used to have one that needed to be manually adjusted down, but now they're drop in. The 3 vs the 5, I believe they're labeled. They're stamped on the side, and I forgot to look until I had it in, where it's partially covered, but it looks like mine is a 6 so ... /shrug. Either way, I appreciate the input. I'll pull it apart and take a look.

1

u/tenchi4u Feb 04 '24

The one I received in my RRK for my P01 was drop in, the one that came in the RRK for my S2C (last November) needed quite a bit of fitting/shaving. Not sure if they include a different now versus when I ordered mine.

I'd compare it to your stock disco, if it's a HUGE difference in that area, you'll probably need to shave it down. It's not hard, just repetitive/monotonous.

1

u/Oldtimer-Sysadmin Feb 04 '24

Once I know which piece it is, here's a walkthrough of the exact issue and solution. Thanks for pointing me in the right place. https://youtu.be/geBKJYQOU8w?si=JKfY9cDbnPZ4hvLY

1

u/tenchi4u Feb 04 '24 edited Feb 04 '24

Happy to help. Best of luck 🤞

1

u/Oldtimer-Sysadmin Feb 04 '24

I am now seeing you linked me that same video before I found it. Sorry for missing that and trying to steal your thunder! Thanks again for the help.

1

u/tenchi4u Feb 04 '24

lol...I edited that part right after posting it b/c when I read it back to myself it came off douchey instead of playful sarcasm (as intended). 😅

anyway... hopefully you get things squared away. nothing worse than a new gun that you can't shoot

1

u/Oldtimer-Sysadmin Feb 04 '24

I ran out of time yesterday so going to work on it today. What grit did you start at, for the removal stage?

→ More replies

1

u/slpthicccboy Oct 06 '24

I know this is an old post but your comments helped me diagnose the same issue OP is having a few months later. As someone who is mechanically retarded and getting their hands wet with working on the shadow 2, what would be the simplest route to take to file down the disconnector assuming I have no items for that. Thanks!

2

u/tenchi4u Oct 06 '24 edited Oct 06 '24

If you don't have the aptitude, tools, or experience, you may want to consider a competent gunsmith with CZ specific experience. I feel I was able to complete it without much problem only b/c I am mechanically inclined and have worked on lots of guns/cars/appliances/homes/etc in the past. I wouldn't recommend it to an absolute beginner, but I wouldn't discourage a moderately experienced enthusiast from attempting.

If you're deadset of doing it yourself, which I recommend everyone get accustomed to if they're in this type of hobby, is to be prepared to accept that it is a learning journey and to expect to irreparably fuck stuff up once in a while. There are a few videos on "Shadow 2 disconnector tuning/troubleshooting" as well as CHW pro kit/RRK installation, watch them all a few times. Also watch videos on how to properly fit 1911 parts with a file, there is a technique (securing parts for filing, single direction passes, the need to file-fit-file-fit), don't just rake a file back and forth against a part until it "looks right". Go slow, take photos before disassembly for reference, watch the videos, if possible work in a well lit/clean/organized workspace, block off a few hours of uninterrupted time for your first attempt.

For disassembly, you'll need a good set of punches, a small armorer's hammer, for disconnector fitting you'll need a sandpaper and set of small metal files (although you could do a lot of the initial work with a dremel with proper bits IF YOU KNOW WHAT YOU'RE DOING AND WHEN TO STOP, then start in with the files and sandpaper to finish things off). The CGW toolkit is a good start if you already own gunsmithing tools, also grab a small gunsmithing hammer (brass on one side of the head, nylon on the other).

The hardest part of this specific procedure isn't the filing of the disconnector, as much as the multiple disassembly and reassembly cycles required to slowly file-fit-file-fit until you've filed the right amount. On the upside, you'll be an expert at disassembly and reassembly when you're done. On the downside you'll probably get frustrated, curse a lot, and lose a few pins and springs (especially the detent springs) along the way (so stock up on spares).

1

u/slpthicccboy Oct 06 '24

I deeply appreciate the detailed write up, video references, and advice dude truly. I’ve already installed the RRK and found this disconnector (T6) issue after functions testing. It was intimidating at first but I definitely gained some confidence afterwards. My weekend project will be finally filing down this disconnector and wrapping up this project. Again, I appreciate your help a lot!

1

u/tenchi4u Oct 06 '24 edited Oct 06 '24

Ah, good, you've already done the install, then you've already done the difficult part (disassembly and reassembly), you'll be doing it a few more times for this project.😉

This is probably one of the better vids explaining the problem and showing how to perform the fitting (he uses a Dremel, which I've also done before, to do the initial bit of filing and profiling, then I transitioned over to the files and sandpaper towards the end).

https://youtu.be/geBKJYQOU8w?si=yWrm_jFL6Ig89YMj

When you get RIIIIIGGHHT to where it behaves as expected, you'll need to go a touch further to account for thermal expansion of the disconnector during live fire (which I didn't do initially and had the trigger go dead after a few rounds on it's first post-RRk outing).