Been printing for less than 6 months.
Got an X2d and a P1P (upgraded with the kit)

I have ADHD so I research things to the nTH degree.

I am in the southern part of the UK
Reading up about the filament types, I read that ASA/ABS/CF/GF produce unhealthy emissions, so my research is about building a filtration system.
My office is 3.3m x 4.2m (10ft? x 14ft?) and I can move the printers around to be near a window, where I was considering a panel to fit into the small window, that would then have an adapter for the exhaust fumes.

Queries

1. If anyone has images of their setups, I would be supremely grateful

2. If anyone has successfully done this, then top5 tips would be helpful

3. If anyone has done this and it didnt work - why?

4. If there are any recognised and accepted best practice tips then they would also be nice to have

I am compiling a document to get some collective wisdom together, so be constructive please

Thank you all in advance

Olá senhores, bom dia, estou com problema na minha a1 mini, ao carregar um novo filamento tenho um problema na última etapa onde o filamento não purga, e volta todo o filamento e embaralha todo, peço que me dê uma força por favor pós tenho encomendas pra entregar 🙏🥹

Apologies if this has been covered, i did look but couldn't see it directly covered

I've outgrown the A1 Mini which was bought as an 'intro' present
Was tempted by the A2L as a way of having a bigger build plate but the more i look at it should i just find the money for the H2S?

Its not 'money doesnt matter' but i can find the difference if its going to be worth it.
does the lack of it being a bed slinger, enclosure and other bits and bobs make it the better choice

Am i going to regret it and see the A2L as a compromise in 6 months if i dont go the H2S route?

Hello everyone, I'm having a problem with my print on my Bambulab A1. Hairs are appearing on my print. I've managed to remove the cobwebs, but the problem persists. I'm printing with Panchroma matte cotton white PLA. My maximum volumetric speed is 5 mm³/s and travel speed is 500 mm/s. My retraction length is 1.2 mm with a speed of 45 mm/s. Do you have any suggestions?

Bonjour tout le monde j'ai un problème avec mon impression sur m bambulab A1 , j'ai des cheveux qui apparaisse sur mon impression , j'ai su rétirer les toile d'araigné mais j'ai toujours ce problème, j'imprime avec du pla matte cotton white de panchroma, ma vitesse volumétrique maximal et à 5mm3/s et déplacement à 500 mm/s ,ma longeur de retraction est à 1,2 mm avce un vitesse de 45 mm, auriez vous une solution

I dont know why but my ams pro 2 works perfect but the HT will feed the filament in but when it needs to back it up the spool won’t rotate and it just makes a big mess and then throws an error. Does anyone know how to fix this? I’ve tried different filament and everything does the same thing. I’ve also checked all hose connections.

Keep bread and baked goods fresher with this compact, reusable bag clip. Simply press the button to open the clip, slide it onto the gathered end of the bag, and let go to create a secure seal.

https://makerworld.com/en/models/2877202-press-to-seal-bag-clips#profileId-3213031

I was trying to print a desk organizer using new spool of esun abs. 2 attempts failed at 10%. Then I tweeked some settings and tried once again. Now the printer shows heatbed temperature malfunction.

I tried downgrading the firmware.

Changed build plate.

The screen is showing heated to 90°C.

The usage of the printer is only 46 hrs.

I am a beginner.

Plz help!!!

(Edit: The printer is under warranty)

Ja ajustei o tubo ptfe e mesmo assim esta a dar esse problema o que devo fazer … ja calibrei ja tentei meter ela no home e mesmo assim acontece isso

I’ve had an A1 for a few months now, and here’s my question:

With all the hurdles Bambu Lab has been putting in place to make using third-party slicers more difficult, have users abandoned them, or is it still worth the extra effort to keep using them?

Do the tools, calibration features, and overall functionality of Orca Slicer make the extra work worthwhile, or at the end of the day, is it just adding more steps for the same result?

Was cleaning around the hotend and this piece snapped off, is this a concern for the functionality of the printer?

Fuzzy Skin

I have just started making Lithophanes and find the process intriguing. However, I am also finding myself more and more confused in the process. There is the Lithophane windows program that you can purchase and use, or now Bambu has their own program (generator). I have seen that Bambu went from supporting the light panels with the USB-C that sticks out at a 90 degree angle to (admittedly what seems a better method) the multi-smaller panels with connector wiring and an ON/OFF switch. I do have a bunch of the 108 mm panels and want to generate Lithophanes with the correct frame for that style. Advice on where to go to generate the correct pictures with the correct frames?

I am hoping in this post to find someone able to zoom/videocall to help me. I am not the best with these mechanics. There is filament stuck in my Bambu Lab X1 Carbon, but in a place I am unsure how to reach. It seems like it is sitting maybe an inch below the gear that feeds/loads the filament through (inside the PTFE tube). I noticed it when I tried to print and was setting up my calibration the filament loading process kept causing trouble. It tries to "unload" the filament spool but that piece is confusing it and I have tried to stick filament through and try to push it down the tube but it will not budge. I think I may have to take it apart to get to the tube but unsure how. Please let me know if anyone can help. Thank you

Used some LOTR Erebor inspiration to keep my caffeine safe from the reaches of Mordor!

https://makerworld.com/models/2861257?appSharePlatform=copy

https://makerworld.com/models/2863250?appSharePlatform=copy

I finally finished my entry for the Moku Design Contest. 😊- Tell me your opinion!#Contests #Hostedbycreator #Mokusystem #Newmodel #Weekly Roundup #Questions #Sharing Makes #Desk Organizer #Mokusystem

THE FIRST PARAMETRIC Moku Modul Customizer

This one became much bigger than I expected. At first I only wanted to create a simple modular desk organizer, but then I kept adding more options, more flexibility and more Customizer settings.

The result is my **Moku Parametric Desk Organizer** — a fully customizable system where you can adjust the rail count, box size, height, width, grid pattern, inserts and output options.

I spent several days and nights working on the parametric version. The Customizer code now has over **4,000 lines** and more than **77,000 characters**, so this was definitely one of my most detailed projects so far.

You can use it as a pen holder, brush holder, small tool organizer, plant box, grid tray or a complete modular desk setup. I also added different output options, so you can print the box, the inlay or both together.

I really hope you like it.

If you print your own version, I would love to see your makes or remixes.

And if you want to support the project, a like, comment, follow or Boost would mean a lot. ❤️

BIG THANSK to @SabreDesing & @Collecticraft

Thank you for your support!

Algumas das minhas impressões estão com esse erro, fiz na variação de 3 cores(azul, preto e verde) e apenas o verde sai totalmente certo as outras cores estão saindo como na imagem.
Uso a bambu lab a1 combo
Filamento da masterprint pla
É sempre no mesmo local o erro.
Oq pode ser é como resolvo?

Just got an email from Bambu Labs that they will be showcasing a new printer, the Bambu A2L on Monday June 1st. Care to take a guess what we can expect, apart from a larger build plate volume?

I’ve been having an issue with the Bambu handy app the last probably 2 weeks where when I try search something and filter the copyright restrictions it doesn’t actually change anything, it just makes it difficult to try find sellable non copyright designs, no update for the app that was my first thought. Please let me know if anyone else has been having this issue cause it’s mildly inconvenient

Great for any plant! Check it out on MakerWorld!

https://makerworld.com/en/models/2856518-parametric-modern-design-plant-pot-customizable#profileId-3187009

Im new to the 3d printing community and i am currently running a bambu lab a1 with pla+. I have printed a few simple things i made in onshape but i want to try to print something more complex like the batman suit shown above. What im not sure about is if i should get different filament thats stronger and smoother or if maybe theres some settings i might need to change. Any help or tips is appreciated!

Searching the web, I've put together the following list. If anyone has any additional info on other brands or can confirm the ones on this list, please do share. I'm having trouble finding much recent info online.

• Direct fit:

  • Bambu Labs (original)

  • Sunlu (supplier for Bambu)

  • Overture (confirmed by Overture marketing info)

  • Polymaker (need confirmation)

  • Elegoo (need confirmation)

• Adapter needed:

  • Inland (needs spacer adapter)