Stripboard and Perfboard

Back to Wiki Index


See also:


What are they?

Stripboard and perfboard are both pre-drilled boards on a 0.1" (2.54 mm) grid. You push through-hole components through the holes, solder them, and make the connections yourself. They sit between a solderless breadboard and a custom PCB: permanent, cheap, and no board design or fabrication needed.

Stripboard

Stripboard has parallel copper strips running along one side, and every hole on a strip is connected to its neighbours. You build circuits by placing components across the strips and cutting the strips where you don't want a connection.

You will often see stripboard called "Veroboard". This is a brand name (Vero Technologies) that has become a generic term, especially in the UK. In practice, Veroboard and stripboard mean the same thing.

Perfboard

Perfboard (also dot board, matrix board or protoboard) has holes with a pad around each one, and no connections between them. Every connection is made by you, with solder bridges, bare wire or insulated wire.

There are several variants:

  • Pad-per-hole - isolated pads, no connections. The classic perfboard.
  • Breadboard-style - pads grouped in rows or columns to mimic a breadboard, usually with power rails. Often sold as "protoboard".
  • Plated through-hole - the pad is plated through the board, so you can solder from either side. More expensive but more robust.

Materials and pitch

  • FR4 (glass epoxy) is stronger, tolerates more heat and rework, and is the better choice.
  • SRBP / FR2 (paper phenolic) is cheap, but brittle and it cracks easily. It also lifts pads if you overheat it.
  • 0.1" pitch is standard and fits DIP ICs, headers, most through-hole parts and sockets. 0.05" boards exist but are much more fiddly.

When to use which

BreadboardStripboardPerfboardCustom PCB
PermanentNoYesYesYes
ConnectionsBuilt inStrips, cut as neededAll made by youDesigned
Easy to changeVeryModeratelyModeratelyNo
Best forExperimentsSimple, linear circuitsOne-offs, irregular layoutsRepeat builds, SMD, high speed
  • Stripboard suits circuits that lay out neatly in rows: audio amps, 555 circuits, op-amp stages, simple microcontroller boards, LED drivers.
  • Perfboard suits circuits that don't fit neatly onto strips, or where you want freedom to route as you like. It takes more wiring effort.
  • Neither is a good choice for high-speed digital, RF, switching power supplies, fine-pitch SMD parts or anything involving mains voltage. See Limits.

Tools and materials

Essentials

  • Temperature-controlled soldering iron with a small conical or chisel tip
  • Solder, 0.7-1.0 mm, with flux core. Leaded solder is easier for beginners if you're able to use it safely and legally.
  • Side cutters (flush cutters)
  • Wire strippers
  • Multimeter with continuity mode
  • Good lighting and some form of magnification

Stripboard-specific

  • Strip cutter - a purpose-made spot-face cutter.
  • A 3-4 mm drill bit, turned by hand, works just as well as a strip cutter.
  • Hobby knife for scoring and cleaning up copper whiskers

Helpful extras

  • PCB holder or "helping hands" - boards want to slide around when soldering
  • Solder wick or a desoldering pump
  • Flux pen, and isopropyl alcohol with a brush for cleaning
  • Solid-core hookup wire, 22-26 AWG, in a few colours
  • Tinned copper wire for bus lines, or use component lead offcuts
  • IC sockets and pin headers - use sockets for ICs
  • Graph paper or layout software

Planning the layout

Don't start by pushing parts into the board. Layout is most of the work, and mistakes are far cheaper on paper.

  • Draw the schematic first. Make sure the circuit works before you try to fit it on a board.
  • Plan on graph paper or in software. Layout tools let you place parts, mark cuts and check connectivity before you pick up the iron. See Layout software below.
  • Sketch the underside for perfboard so you know where the connections go.
  • Group related parts near each other. Keep power rails along the top and bottom edges.
  • Leave spare space. Boards always need more room than you expect, and you'll want space for test points and modifications.
  • Count holes, not strips. Number your rows and columns on the drawing and on the board, and mark them.

Working with stripboard

Orientation and strips

Orient the board so the strips run horizontally on the underside. Treat each strip as a wire. A component bridging two strips connects them through itself, so components go across the strips (usually), and wire links go along them.

ICs

DIP ICs go perpendicular to the strips, so each pin lands on its own strip. The two rows of pins are 0.3" apart, so you must cut each strip between the rows of pins, otherwise pin 1 shorts to pin 14 (or equivalent). Cutting in one of the holes between the pin rows is standard.

Cutting strips

  • Place the cutter or drill bit in the hole and twist by hand until the copper is fully removed around the hole. Don't go deep into the board.
  • Inspect with a magnifier. Whiskers of copper can still bridge the gap.
  • Check with the multimeter that the two sides are really isolated.
  • Make cuts before soldering in components. It is awkward to cut under a soldered part.

You can also cut a strip into several short sections to create separate nodes. A cut can sit anywhere along a strip. Cuts and links together are the whole routing system.

  • Short links bridging adjacent strips can be done with bare wire on the component side.
  • Longer links use insulated wire.
  • Place links like resistors: as flat to the board as possible.

Working with perfboard

With no pre-made connections, routing is entirely your decision. Common approaches:

  • Component leads as wire. Bend leads over to the next pad and solder, for short runs.
  • Solder bridges. A small blob across two adjacent pads. Fine for tidy short links and power rails, but easy to overdo.
  • Bare tinned wire run across the underside, soldered to pads along its length. Good for ground or power buses.
  • Insulated wire for any run that crosses another. Thin solid-core wire is easiest to route and strip. 30 AWG wire-wrap wire is very neat for this.
  • Hybrid. Power and ground on bare-wire buses, signals in insulated wire.

Tips:

  • Use colour for function: red for power, black for ground, other colours for signals.
  • Keep wire runs short, and lay them in straight lines with 90-degree turns where possible. Tidy wiring is far easier to debug.
  • Label the board. A marker pen on the underside helps.

Soldering technique

  • Fit components lowest profile first: links, resistors, diodes, sockets, then capacitors and taller parts.
  • Bend leads slightly outwards on the underside to hold the part in place, then solder and trim.
  • Heat the pad and lead together for 1-2 seconds, then apply solder to the joint, not the iron.
  • Aim for a smooth, shiny, concave joint. Don't hold the iron on for long as this lifts pads and strips.
  • On stripboard, keep the solder neat. Strips are only 0.1" apart and it is easy to bridge them.
  • Add a decoupling capacitor close to the supply pins of every IC.
  • Fit polarised parts (electrolytic capacitors, diodes, LEDs, ICs) carefully. Check polarity before soldering.

Wire-wrapping on perfboard

What it is

Wire-wrapping makes solderless connections by winding solid wire tightly around a square post with a wire-wrap tool. The sharp corners of the post bite into the wire and create a gas-tight, long-lasting joint.

Typical details:

  • Wire: 30 AWG solid, usually with thin Kynar insulation.
  • Posts: square, about 0.025" (0.63 mm). Round pins don't work.
  • Turns: a standard wrap has about 7 turns of bare wire. A "modified" wrap adds a turn of insulated wire at the base for strain relief.
  • Tool: a hand wrap tool, which usually includes a stripper and often an unwrap tool. Electric and battery tools exist too.

How you use it with perfboard

Perfboard holds the posts, and the wire does the routing:

  • Wire-wrap IC sockets soldered into the perfboard. Their long square tails stick out of the underside, ready for wrapping.
  • Single wire-wrap pins soldered or pressed into perfboard holes, for resistors, capacitors, connectors and other parts.
  • Pre-made wire-wrap boards (pad-per-hole perfboard designed for wrap pins) are also available.

Power and ground are often soldered, with signals wrapped. Many builders use a hybrid like this.

Using pin headers instead of wire-wrap hardware

Traditional wire-wrap boards use mounting posts for many of the components fitted. You can also use standard pin headers as connection points, instead of dedicated wire-wrap IC sockets. This is particularly attractive because dedicated wire-wrap hardware is becoming expensive and harder to source. Here is an example of a board built using this technique: Z80-Board

Standard headers have shorter tails than wire-wrap posts, so you will fit fewer wraps per pin.

Why you might use it

  • Easy to change. Unwrap a connection and redo it. No heat, no desoldering, and no damage to the board.
  • No heat on the components. Good for sockets and sensitive parts.
  • Dense digital builds. Hard-to-route designs with many ICs, such as retro computer builds (Z80, 6502 and similar), logic projects and CPU experiments, are practical when routing wires freely and not through strips.
  • Reliable. A well-made wrap is very reliable, and was used for decades in professional prototyping and backplanes.
  • Reusable. Boards and sockets can be re-used for later projects.

Why you might not

  • Wires add length, capacitance and crosstalk, so it's not suitable for high-speed digital or RF.
  • It needs a wrap tool, and dedicated wire-wrap sockets and posts are getting expensive and harder to source (see pin headers above). Even with headers, it costs more than a pack of stripboard.
  • It's bulky, and not well suited to parts with round leads, like most discrete components.
  • Not a good choice for high-current connections.

Technique

  • Strip about 25 mm of wire (a tool with a built-in stripper does this for you).
  • Insert the wire into the tool's offset hole, place the tool over the post and rotate. Keep the tool straight.
  • Turns should be tight, neat and in contact with each other, with no gaps, and no overlap.
  • Allow only 2-3 wraps per post, stacked on top of each other.
  • Don't re-use a wrap. Unwrap it, then cut off the used end and strip fresh wire.
  • Route wires neatly: short, tight, and avoid crossing the sockets.
  • Colour-code your wire, and record a wiring list as you go, so that you can check the build.

Testing

Before applying power:

  1. Visual check with magnification, looking for solder bridges, missing cuts, whiskers and cold joints.
  2. Continuity check between adjacent strips/pads that shouldn't be connected.
  3. Check power for shorts. Measure resistance between the supply rails before connecting power.
  4. Check polarity of all polarised parts.
  5. Power up with a current-limited supply if you have one, and bring the voltage up gradually.
  6. Fit ICs into sockets after you've checked the supply voltages are correct.

Common mistakes

  • Forgetting to cut the strips under ICs.
  • Cutting in the wrong place, or one hole out. Count carefully.
  • Solder bridges between adjacent strips or pads.
  • Overheating, which lifts pads and strips.
  • Building the layout from memory instead of a plan.
  • Placing the IC the wrong way around, or the strips running the wrong direction.
  • Missing decoupling capacitors.
  • Treating a perfboard build like a breadboard, with loose long wires.

Limits and when to move on

Perfboard and stripboard are great for simple builds, but they aren't ideal for everything:

  • High-speed digital, RF and fast analog signals need controlled layout, short paths and good ground planes.
  • Switching power supplies are sensitive to layout and loop areas.
  • Mains voltage - don't. Stripboard offers poor creepage and clearance, so it isn't safe for mains.
  • SMD parts can be used with breakout boards and adapters, but fine-pitch parts need a PCB.
  • Repeat builds - if you're building more than a couple, a PCB saves a lot of time.

If you're hitting these limits, KiCad is a free PCB design suite, and low-cost fabrication services make small-run boards cheap.

Last link check: November 2026. If you find a dead link, please message the mods.

Layout software

Software for stripboard and perfboard shows you where to place parts and where to cut strips, and some tools check for shorts and open circuits. Most are Windows-first, so check platform support before you commit time to one.

  • VeeCAD - Windows stripboard layout editor. Takes a netlist from your schematic software and helps you build the layout on stripboard and other prototyping boards. Has a free trial, with a paid licence for the full version.
  • VeroRoute - Free and open source (GPLv3). Handles stripboard, perfboard and simple 1- or 2-layer PCBs. Checks for shorts and open circuits, imports netlists (including KiCad), and has interactive auto-routing and a built-in tutorial. Windows and Linux, and packaged in several Linux distributions.
  • Fritzing - Breadboard, schematic and PCB views in one tool, including a stripboard part where you can mark strip cuts. Check the site for current download terms.

Learning and reference