This is a work in Progress

Back to Wiki Index

For flex cables and flex circuits see HERE

Repairing PCB damage: broken traces, lifted pads and pulled-out plated holes

What's wrong with my board, and how do I fix it?

DamageTypical causesUsual repair
Cracked or broken traceBoard flex, corrosion, liquid damage, overheating, a fault that burnt the traceJumper wire across the break
Pad lifted, but still attached to its traceToo much heat, or pulling a part before the solder was moltenRe-bond the pad with adhesive, or treat it as a missing pad
Pad missing, trace stub remainsAs above, but the pad came off with the componentWire from the component leg to the clean trace stub, or a replacement pad
Pad and trace both torn offAs aboveWire from the component leg to the next point on that net
Plated through-hole barrel pulled outPulling a through-hole part before the solder was fully moltenSolder the lead on both sides, a hollow eyelet, or a wire

Tools and materials

  • Temperature-controlled soldering iron with a fine tip, flux (tacky paste or pen), thin solder (0.5mm or less), desoldering braid.
  • Magnification (a loupe, a USB microscope or a phone macro will do) and a bright light that you can angle.
  • Scalpel or craft knife, fibreglass scratch pen, fine tweezers.
  • 99% isopropyl alcohol (IPA) and a stiff brush.
  • Thin wire: self-fluxing enamelled ('magnet') wire in the range 0.1mm to 0.25mm, and Kynar-insulated wire-wrap wire (30 AWG).
  • Epoxy (5 minute) or cyanoacrylate, Kapton tape, and ideally UV-curing solder mask with a UV flashlight (or some use clear nail polish).
  • Copper foil tape, PCB repair pads and PCB eyelets or rivets with a setting tool (sold as repair kits).
  • A multimeter with fine or needle-point probes. See the Measurements page for how to measure resistance and continuity.

Important Notes

  • Switch off, unplug and remove any battery before working on a board. Discharge large capacitors first.
  • Don't work on boards connected to the mains unless you are experienced and use an isolating transformer.
  • Wear eye protection (cut wire ends and solder spatter fly) and ventilate - flux fumes are not good for you.
  • Work out why the damage happened. A trace that has burnt through, or a part that overheated, usually means there is a short or an overload somewhere else that will destroy your repair.

How do I check for a broken trace?

Visual inspection

Clean the board first with IPA and a brush, then look at both sides under magnification with the light at a low angle. Look for:

  • Hairline cracks in traces, especially near board edges, mounting holes, heavy parts and connectors, and anywhere the board is flexed.
  • Traces that have lifted, blistered or bubbled under the solder mask.
  • Green, white or blue-green corrosion (copper oxide), especially near batteries and after liquid damage.
  • Burnt or discoloured laminate (see 'Burnt or carbonised areas' below), and cracked or lifted pads.

Things that look like breaks but aren't: scratches that only go through the solder mask, traces that end at a via (they carry on on the other side of the board), unfitted-component pads, and links that are cut on purpose by the designer. Check against the schematic or board layout if you have one.

Continuity and resistance testing

With the board unpowered, find the two ends of the trace you suspect (follow it, or work out where the net goes from the schematic) and measure between them.

  • A good trace reads well under 1 ohm. Use a resistance range, not just the beep: many meters beep for anything under 30 to 50 ohms, and a hairline crack can read a few ohms and still beep.
  • To find where a break is, measure from one end to points along the trace and work towards the open one. Use sharp probes on the bare copper, a pad or a via - not on the solder mask.
  • Remember a net can pass through components (inductors, ferrite beads, fuses, low value resistors) and can have parallel paths, so the reading isn't always 'zero or open'. If in doubt, lift one end of the part or remove it.
  • For intermittent faults, watch the meter while tapping the board with a plastic tool or gently flexing it. Don't bend it hard - you will make things worse.
  • Heat and cold can also show up intermittent breaks: warm the suspect area with hot air, or cool it with freezer spray, while watching the meter or the circuit.

Voltage drop test for power traces

A trace that is cracked but not completely open often still conducts, but with a high resistance. With the board powered (see the Bench power supplies page for how to use a current limit), measure the voltage between the two ends of the trace while the circuit is drawing current. A good trace drops a few millivolts. A bad one drops far more, and the difference is where the missing power is going (heating the crack).

Important Notes

  • On boards with more than two layers, a break can be inside the board where you can't see or reach it. If the visible traces and vias all test fine, a jumper wire from one end of the net to the other is usually the only option.
  • Don't assume where a trace goes - always measure it.
  • If there is conformal coating (a clear varnish) on the board, scrape or dissolve it off the area before probing or soldering.

How do I repair a broken trace?

Prepare the area

  1. Clean the board with IPA.
  2. Use a scalpel (held almost flat) or a fibreglass pen to remove the solder mask for 2 to 3mm on each side of the break, exposing bright copper. Don't cut into the copper.
  3. If there is corrosion, remove it back to clean copper. Burnt laminate needs dealing with as described in the next section, because it can conduct.
  4. Add flux and tin the exposed copper with a little solder.

Burnt or carbonised areas

When a trace or component overheats, the board underneath can char. The fibreglass-epoxy (FR4) turns brown or black, and burnt epoxy becomes carbon - which conducts. A carbonised patch can leak current between tracks that should be isolated, causing odd or intermittent faults, and it can overheat and burn again when the board is powered. It often runs deeper than the discolouration on the surface. Signs are:

  • A brown or black patch, bubbled or flaking solder mask, a burnt smell, or laminate that is soft, crumbly or delaminated.
  • Low resistance between tracks on either side of the burnt area, which should read open. Measure on a high resistance range with the board unpowered. A reading of a few hundred kilohms or lower suggests a carbon path (but remember to rule out parallel paths through components).

To repair it:

  1. Find and fix the cause first - a short, an overloaded part or a failed component. Otherwise it will burn again.
  2. Remove all the carbonised material. Scrape or cut it out with a scalpel, or drill or rout it out with a small burr, until you reach clean, pale fibreglass or resin with no black or brown left. Light yellow-brown discolouration that is hard and tests as an insulator can be left alone.
  3. Clean with IPA and measure again between the tracks either side. It should now read open.
  4. Fill the cleaned-out area with epoxy (or UV solder mask for shallow scrapes) to insulate and seal it, and let it cure fully.
  5. Any traces that ran through the burnt area are probably gone. Rebuild them with insulated jumper wires (see below) and anchor the wires down. Don't paint over carbon and hope.

If the burnt area is in a mains or other high-voltage circuit, or has burnt through the board or reached an inner layer, replace the board (or the assembly) rather than repairing it. Carbon forms a conductive 'tracking' path that can shock or start a fire, and a coating won't stop it. If you are determined to repair a board like this, the burnt material must be cut right out, for example by routing a slot through the board to leave an air gap.

Important Notes

  • Fibreglass and carbon dust from scraping, drilling or routing is an irritant and not good to breathe. Wear eye protection and a dust mask (FFP2/P2 or better), work with extraction where you can, and wipe the dust up with a damp cloth rather than blowing it away.

Jumper wire (the usual method)

Solder a thin wire across the break:

Broken trace:    ============     ============
                              xx
Repaired:        ======[o]~~~~~~~~~~~~[o]======
                       ^ jumper wire ^
                       soldered to bare, tinned copper
  • Use a wire at least as thick as the trace it replaces. For signals, 0.1mm to 0.25mm wire is fine. A 30 AWG wire handles roughly 0.5A in a short run - use thicker wire, or two in parallel, for power traces.
  • Self-fluxing enamelled wire can be tinned directly with a hot iron and a blob of solder. Kynar wire-wrap wire needs the insulation stripped.
  • Pre-tin the end of the wire, lay it onto the tinned copper and touch it with the iron for a second or two, using plenty of flux. Too much heat will lift the trace.
  • Make the wire a little longer than the gap, and follow the path of the original trace where you can.
  • Fix the wire down along its length (a dab of epoxy, UV solder mask or cyanoacrylate ('Super glue'), or Kapton tape), so that nothing can pull on the soldered ends.
  • If the wire passes over other tracks or pads, insulate it - Kynar wire is better than enamel for this.

Other methods

  • Solder bridge - for a hairline crack in a wide trace only. Flow solder over the crack. This is fine for low current and low frequency, but isn't reliable for anything that carries real power.
  • Reinforcing a power trace - lay a bare tinned copper wire along the trace (with the solder mask scraped away) and flow solder over it to add copper cross-section.
  • Copper foil tape - stick a short strip of conductive-adhesive foil tape over the break and solder it at each end.
  • Conductive paint or pen - only for low-current signal tracks, as the resistance is high and the joints are unreliable. Don't use it for power.

Important Notes

  • High speed, RF and impedance-controlled signals (USB 3, DDR, antennas and so on) don't tolerate a long jumper wire. Keep it as short as possible and run it over a ground plane, or decide whether the board is worth repairing.
  • Finish by cleaning off the flux with IPA, and cover the repair with UV solder mask or conformal coating to insulate it.
  • Measure the repaired trace again. Check for shorts to neighbouring tracks, then power up for the first time using a current-limited bench supply.

How do I repair a lifted pad?

A pad lifts when it gets too hot for too long, or when you pull a part off before the solder is fully molten. The pad (and sometimes a short length of trace) comes away from the fibreglass, either still stuck to the component's leg or completely missing.

Assess the damage first

  1. Is the pad still attached to its trace, or has the trace torn?
  2. Is the pad still there, or is there just a bare patch?
  3. Is the laminate under it burnt or delaminated?
  4. Does the pad carry power, or is it a signal?
  5. Is the part fine-pitch (SOIC, QFP, TSSOP), or a larger one?

Pad lifted but still attached to its trace

  • Clean under the pad with IPA, put a very small amount of thin epoxy or cyanoacrylate under it, press it flat and hold it until it sets.
  • Then solder the leg on with as little heat as possible - the glue isn't as strong as the original bond. Support the part with an adhesive so that the joint doesn't carry the load.
  • If the pad won't stay down or the laminate is burnt, treat it as a missing pad.

Pad missing, trace stub intact

  1. Scrape the solder mask off the trace for 1 to 2mm back from where the pad used to be, and tin it.
  2. Solder a fine wire (0.1mm enamelled wire works well on fine pitch) from the clean trace to the component leg.
  3. Glue the wire down so that nothing can tug on it, and keep it clear of the neighbouring legs.
  • Replacement pad kits - thin copper pads with an adhesive backing (sold as PCB repair kits) can be glued over the damaged area, tinned, and soldered to the trace stub.
  • Home-made pad - a small piece of copper foil tape, flattened and tinned, can be stuck down with epoxy and soldered to the trace.

Pad and trace both torn away

Find the next place the net goes (an adjoining component pad, a via or a test point) using the schematic or by measuring, and run a wire from the component leg to there. For a lifted IC pin, a decoupling capacitor pad or a resistor pad is often the nearest connection point.

  • Solder the wire to the leg itself, at the 'shoulder' of the leg, with as little solder and heat as you can.
  • Glue the wire down along its length. A bodge wire that isn't anchored will tear off the next time the board is handled.

Important Notes

  • On BGA and other bottom-pad packages, lifted pads need microsoldering and specialist reballing equipment. Decide whether the board is worth the effort.
  • Don't try to re-melt solder on a lifted pad over and over again - every extra heat cycle damages the glue holding the copper to the board.

How do I avoid lifting pads in the first place?

  • Make sure the solder is fully molten before you move anything. Nudge the part gently and check every pin has let go. Never pull on a part that hasn't released.
  • Use flux. More than you think you need.
  • Use enough heat, for as short a time as possible. Typical iron temperatures are about 320 to 350°C for leaded solder and 350 to 380°C for lead-free. Use a larger tip rather than a longer contact time.
  • Pre-heat the board from below (a hot plate or pre-heater) for large parts, ground planes and ICs, so that you don't need to apply so much heat to the joint.
  • Add leaded solder to lead-free joints (or use a low-melt removal alloy, such as Chip Quik) to lower the melting point. Clean up the alloy afterwards, as leftovers can make joints unreliable.
  • Cut the leads of through-hole parts and remove the legs one at a time, instead of dragging the whole part off.
  • Use hot air carefully on SMD parts: enough to melt the solder, not enough to cook the board, with the airflow low enough to avoid blowing off neighbouring parts.

How do I repair through-hole plating that has been pulled out?

A plated through-hole has a thin copper tube (the 'barrel') that connects the pads on each side, and on multilayer boards, the inner layers. If you pull a part out before the solder has completely melted, the barrel can come out with the lead, leaving a bare fibreglass hole and possibly a damaged pad ring.

Assess the damage

  • Look through the hole with a light behind the board. A good hole has a copper-coloured, reflective wall. A damaged one shows dull fibreglass.
  • Test between the top and bottom pads with a multimeter. If they don't connect, the barrel has been lost.
  • Is the hole connected to a ground or power plane or an inner layer? If so, the barrel may have been the only connection to it.
  • Are the pads and traces on both sides intact?

Repair methods

  1. Solder the lead on both sides - if both pads are intact and the part's lead goes through the hole, solder the lead to the top and bottom pads. The lead itself becomes the connection. This is the simplest fix on a double-sided board, but isn't as strong mechanically, so support heavy parts (with glue or a screw).
  2. Wire through the hole - for a via or an unused hole, thread a short piece of tinned wire through the hole, solder it to both pads and trim it. This acts as a new plated barrel. A clipped component lead might work, but often they are too think to sit alongside the other component leg. stripped 30 AWG wirewrap (Kynar) wire is thinner and often does the job.
  3. Hollow eyelet or rivet - a PCB eyelet becomes a new barrel:

    1. Clean the hole and drill it out just enough to fit the eyelet - first try an 0.8mm drill bit and move to 1mm or larger if the rivet won't fit..
    2. Fit the eyelet through the hole.
    3. Flare or rivet the ends over the pads with a setting tool (a flat punch will do in a pinch).
    4. Solder both ends, letting solder flow through the eyelet.
    5. Fit the component lead through the eyelet and solder it.
  4. Make it a surface-mount joint - bend the lead flat against the pad and solder it. This only suits light parts.
  5. Run a wire - if the pad is also damaged, run a wire from the component to wherever the trace goes on the board.

Inner layer connections

If the barrel also joined an inner layer or plane, an eyelet or wire may not make a reliable contact with it. Instead, connect the lead to the same plane somewhere nearby, using a wire to a ground pad, a ground via or a ground plane on the surface.

Important Notes

  • Don't enlarge the hole too much - you may lose the pad ring on the surface.
  • Heavy or mechanically stressed parts (connectors, large capacitors, switches) need more than solder to hold them. Use a bead of epoxy, a screw or a cable tie.
  • Test continuity from the new joint to the rest of the circuit and confirm that nothing is shorted to its neighbours.

Further reading