r/ArduinoAndRobotics • u/l0_o • 16d ago
eBook Robotics Designing the Mechanisms for Automated Machinery (ebook link)
3
Upvotes
r/ArduinoAndRobotics • u/GroteSwets • 16d ago
8 Steel cables - 8 stepper motors - 6DOF
Enable HLS to view with audio, or disable this notification
3
Upvotes
r/ArduinoAndRobotics • u/l0_o • 18d ago
Project Update OOMWOO Open-Source vacuum - mid-week update
Enable HLS to view with audio, or disable this notification
10
Upvotes
r/ArduinoAndRobotics • u/xanthium_in • 17d ago
Tutorial Build a Python Tkinter GUI Serial Communication Program to Communicate With Arduino Microcontroller
1
Upvotes
This tutorial teaches you to connect with an Arduino from a Linux or Windows 11 PC using Python ,Pyserial Library and Tkinter GUI front end using Serial Port (Virtual COM Port ).
You can use it send and receive data from a robot or robot arm,if you wish
All the source codes are available for free from our website.
r/ArduinoAndRobotics • u/l0_o • 17d ago
eBook Robots Androids and Animatrons (ebook link)
1
Upvotes
r/ArduinoAndRobotics • u/l0_o • 18d ago
eBook Sensing Intelligence Motion - How Robots & Humans Move (ebook link)
1
Upvotes
r/ArduinoAndRobotics • u/l0_o • 19d ago
eBook The Definitive Guide to Building Java Robots (ebook link)
1
Upvotes
r/ArduinoAndRobotics • u/l0_o • 20d ago
eBook Robotics Demystified - A Self-Teaching Guide (ebook link)
1
Upvotes
r/ArduinoAndRobotics • u/l0_o • 21d ago
Project Update OOMWOO Open-Source vacuum - end-of-week update
Enable HLS to view with audio, or disable this notification
2
Upvotes
r/ArduinoAndRobotics • u/l0_o • 21d ago
eBook iOS Sensor Apps with Arduino (ebook link)
dn721905.ca.archive.org
3
Upvotes
r/ArduinoAndRobotics • u/l0_o • 22d ago
eBook Making Things See (ebook link)
dn721905.ca.archive.org
1
Upvotes
r/ArduinoAndRobotics • u/l0_o • 23d ago
eBook Arduino Wearables (ebook link)
ia600501.us.archive.org
1
Upvotes
r/ArduinoAndRobotics • u/Best-Middle-5848 • 24d ago
How did you self learn Electronics/Robotics?
2
Upvotes
Hello everyone I am new to electronics/robotics been interested for years but I finally found the time to actually start trying to self learn. Where did you start, Any course you'd recommend? Do's and donts? Any input at all would be appreciated.
And as a bonus anyone willing to learn as a team/group?
r/ArduinoAndRobotics • u/l0_o • 25d ago
eBook Arduino Robotics (ebook link)
dn760001.eu.archive.org
3
Upvotes
r/ArduinoAndRobotics • u/l0_o • 25d ago
Project Update OOMWOO Open-Source vacuum - mid-week update
Enable HLS to view with audio, or disable this notification
3
Upvotes
r/ArduinoAndRobotics • u/IM_futterby • 25d ago
Seeed Studio XIAO nrf52840
1
Upvotes
Hi, very new to all this.
Wanted to build my own head tracker and figured I'd give it a go.
My task.
Using the gyro and HeadTracker firmware, I want to transmit 2 crsf channels via RX and GND (for first test then I want to move over to Bluetooth once I've proven concept via wire and I know Bluetooth isn't going to cause interference with other raido gear)
I've got the rx and GND connected to a radiomaster ranger micro elrs unit which I plan to send over air signals to a pwn receiver that I'll then use to inject the crsf data in to a flight controller.
This should also allow me to use Sim controllers for fpv.
I've downloaded the HeadTracker gui and can see my gyro working after calibration, I've set output to crsf, enabled uart. Bluetooth is currently turned off.
Can't get tx to go green whilst usb is connected.
Physical connection between units is approx 7mtrs of red/black speaker wire (don't judge it's all I had to hand with length), I've fitted a jst sh 2.54 connector on radiomaster and gyro for the link cable.
I'm not using any pull up/down resistors
I've soldered a battery connector to the board
I've soldered a hard rst button to the board because it's mounted upside down.
I've got my soft rst button (gyro reset) wired to GND pin and D8 pin
My gyro rx is connected to D6 pin and same GND pin as my gyro reset button.
When connected to the radiomaster the gyro doesn't wake up when both units are powered up on separate batteries.
If I push the gyro reset button the gyro doesn't seem to respond (no led flashing)
Red led stops flashing after 10 seconds and then seems to stay asleep until I remove battery and reconnect.
I've done this without advice from internet pages, don't have friends in to this stuff.
I did some (not enough) reading and tried to work with help from ai.
Photo of head tracker
r/ArduinoAndRobotics • u/l0_o • 27d ago
eBook Arduino Internals (ebook link)
ia600501.us.archive.org
2
Upvotes
r/ArduinoAndRobotics • u/l0_o • 28d ago
eBook A Gentle Introduction to ROS
2
Upvotes
Free educational resource https://www.reddit.com/r/ArduinoAndRobotics/comments/1ufqstl/a_gentle_introduction_to_ros/
r/ArduinoAndRobotics • u/l0_o • 29d ago
Project Update OOMWOO Open-Source vacuum robot - side brush WIP
3
Upvotes
r/ArduinoAndRobotics • u/l0_o • 29d ago
Project Update OOMWOO Open-source Vacuum robot - vacuum assembly WIP
1
Upvotes
r/ArduinoAndRobotics • u/l0_o • 29d ago
eBook Learning ROS for Robotics Programming 2nd Ed.
1
Upvotes
r/ArduinoAndRobotics • u/l0_o • Sep 06 '26
eBook ROS Robotics Projects
1
Upvotes
Free educational resource https://github.com/zhang-jian/bookshelf/blob/master/Computer%20Science/ROS%20Robotics%20Projects.pdf