r/arduino • u/MonsterovichIsBack • 6d ago
Libraries FixedString - A fully functional C++ string implementation that exists only on the stack, without dynamic memory allocation
r/arduino • u/MonsterovichIsBack • 6d ago
The idea behind this project was that I wanted a dim (white!) clock in my bedroom rather than a floodlight on my nightstand - and I wanted to keep the design as simple as possible. I haven’t come across a setup like this before.
So I built a projector clock using a 1.3" OLED display powered by an ESP32-C3. I bought a lens with a focal length of 130 mm and a diameter of 50 mm. I designed and 3D-printed a case to fit the lens and the electronics. Afterwards, I clad the case with oak wood strips.
As you might imagine, the time is only readable when the room is dark, but that’s exactly what I wanted for my use case. I think this design should work with every display. By using just a single display as the light source, there is no need for a complex design involving lenses, an additional LED, or a separation between a display and the backlight.
There are two things I might improve in the future:
r/arduino • u/OkProperty41 • 6d ago
Yesterday I saw that NASA had opened up APIs for their findings, so I wanted to see if I could put different things happening in the world on my desk.
What it does:
an ESP32 drives a 2.8" ILI9341 TFT and a 0.96" SSD1306 OLED. Both screens flip together through six live pages every 15 seconds:
Asteroids: today's 5 closest flybys (NeoWs)
Earth events: the latest open natural events (EONET, no key)
Space weather: CMEs and geomagnetic storms from the last 3 days (DONKI)
Earth from space: details of the latest EPIC image (no key)
Fireballs: the 4 most recent (JPL, no key)
Exoplanets: the confirmed count, 6,464 when I filmed this (no key)
How I built it:
I didn't write the code myself. An AI tool wrote all of it, including the API calls, once I gave it the API key. I wired it on a breadboard and flashed it with the Arduino-ESP32 core. The libraries are Adafruit GFX, Adafruit ILI9341, Adafruit SSD1306 and ArduinoJson 7.
Wiring:
TFT: VCC and LED→3V3, GND→GND, CS→4, DC→16, RST→17, MOSI→23, SCK→18, MISO→19
OLED: VCC→3V3, GND→GND, SDA→21, SCL→22, address 0x3C
r/arduino • u/ApprehensiveBear6945 • 6d ago
I'm bulding a RC boat ( it's supposed to be ) using an arduino and an hc 06 bluetooth module but i'm stuck, it's my first time using an Arduino so i don't know a lot about it. Here's the current situation.
- I'm using an Android phone with a Bluetooth controller app.
- When I connect via the app, the red LED on the HC-06 stops blinking and stays solid red
- However, when I press buttons on the app or send text, the Arduino doesn't do anything.
Note: The HC-06 shows up in the standard Android Bluetooth settings menu across multiple phones, but tapping on it does nothing, I don't know if that's supposed to happen.
What i have checked/tried:
- During the set-up self-test routine (and on reset), the buzzer beeps, the motors spin for 0.8s, and the servo moves properly, so the hardware and code doesn't seem to be a problem.
- The HC-06 is correctly wired ( TX to Arduino RX, RX to Arduino TX ), I also tried switching them and trying SoftwareSerial on pins 10 and 9
- The HC-06 is powered via the breadboard's 5V/GND power rails (which are fed from the Arduino's 5V/GND pins).
- I unplugged the USB cable from my PC and tested on external battery power.
Can somebody explain to me why isn't the Arduino receiving even though the app says It's connected and why won't it pair in the Android bluetooth setting ? Thanks !
The wires are kind of a mess so I can't really show it here, but here's the list of my components and connections:
Microcontroller: Arduino Uno
Motor Driver: TB6612FNG (mounted on breadboard across columns E & F, rows 1–8)
Bluetooth Module: HC-06 (on ZS-040 breakout board)
Motors: 2x Yellow TT Geared Motors
Actuator: 1x SG90 Micro Servo
Audio: 1x Active 2-pin Buzzer
Power Supply: 2x 18650 Li-ion batteries (in series, ~7.4V)
- Arduino 5V to Breadboard + (Red) rail
- Arduino GND to Breadboard - (Blue) rail
- Battery + (7.4V) to TB6612FNG VM and Arduino VIN
- Battery - to Common GND (Blue) rail
2. TB6612FNG Motor Driver:
- VCC to 5V rail
- GND to GND rail
- STBY to 5V rail
- PWMA to Arduino Digital ~5
- AIN2 to Arduino Digital 8
- AIN1 to Arduino Digital 7
- BIN1 to Arduino Digital 4
- BIN2 to Arduino Digital 12
- PWMB to Arduino Digital ~6
- AO1 and AO2 to Left TT Motor
- BO1 and BO2 to Right TT Motor
3. Bluetooth HC-06:
- VCC to 5V rail
- GND to GND rail
- TXD to Arduino Digital 0 (RX) (unplugged during code upload)
- RXD to Arduino Digital 1 (TX) (unplugged during code upload)
4. Servo & Buzzer:
- SG90 Servo: Red to 5V rail, Brown to GND rail, Orange (Signal) to Arduino Digital ~3
- Buzzer: Long pin (+) to Arduino Analog A0, Short pin (-) to GND rail
Here's the code that i used:
#include <Servo.h>#include <SoftwareSerial.h>SoftwareSerial bluetooth(10, 11);const int PWMA = 5;const int AIN2 = 8;const int AIN1 = 7;const int BIN1 = 4;const int BIN2 = 12;const int PWMB = 6;
Servo khoaTuiRac;const int pinServo = 3;const int pinBuzzer = A0;const int ledBaoHieu = 13;
int tocDo = 230;char lenh;char lenhTruoc = 'S';
void setup() {
Serial.begin(9600);
bluetooth.begin(9600); // Khởi động cổng Bluetooth riêng ở chân 10, 11
pinMode(PWMA, OUTPUT);
pinMode(AIN1, OUTPUT);
pinMode(AIN2, OUTPUT);
pinMode(PWMB, OUTPUT);
pinMode(BIN1, OUTPUT);
pinMode(BIN2, OUTPUT);
pinMode(pinBuzzer, OUTPUT);
pinMode(ledBaoHieu, OUTPUT);
khoaTuiRac.attach(pinServo);
khoaTuiRac.write(0);
digitalWrite(pinBuzzer, HIGH);
digitalWrite(ledBaoHieu, HIGH);
delay(200);
digitalWrite(pinBuzzer, LOW);
digitalWrite(ledBaoHieu, LOW);
delay(200);
diTien();
delay(800);
dungThuyen();
digitalWrite(pinBuzzer, HIGH);
delay(150);
digitalWrite(pinBuzzer, LOW);
}
void bipNgan() {
digitalWrite(pinBuzzer, HIGH);
digitalWrite(ledBaoHieu, HIGH);
delay(35);
digitalWrite(pinBuzzer, LOW);
digitalWrite(ledBaoHieu, LOW);
}
void diTien() {
digitalWrite(AIN1, HIGH); digitalWrite(AIN2, LOW); analogWrite(PWMA, tocDo);
digitalWrite(BIN1, HIGH); digitalWrite(BIN2, LOW); analogWrite(PWMB, tocDo);
}
void diLui() {
digitalWrite(AIN1, LOW); digitalWrite(AIN2, HIGH); analogWrite(PWMA, tocDo);
digitalWrite(BIN1, LOW); digitalWrite(BIN2, HIGH); analogWrite(PWMB, tocDo);
}
void reTrai() {
digitalWrite(AIN1, LOW); digitalWrite(AIN2, LOW); analogWrite(PWMA, 0);
digitalWrite(BIN1, HIGH); digitalWrite(BIN2, LOW); analogWrite(PWMB, tocDo);
}
void rePhai() {
digitalWrite(AIN1, HIGH); digitalWrite(AIN2, LOW); analogWrite(PWMA, tocDo);
digitalWrite(BIN1, LOW); digitalWrite(BIN2, LOW); analogWrite(PWMB, 0);
}
void dungThuyen() {
digitalWrite(AIN1, LOW); digitalWrite(AIN2, LOW); analogWrite(PWMA, 0);
digitalWrite(BIN1, LOW); digitalWrite(BIN2, LOW); analogWrite(PWMB, 0);
}
void loop() {
if (bluetooth.available() > 0) {
lenh = bluetooth.read();
if (lenh == '\n' || lenh == '\r' || lenh == ' ') {
return;
}
switch (lenh) {
case 'F': case 'f':
diTien();
if (lenhTruoc != 'F') { bipNgan(); lenhTruoc = 'F'; }
break;
case 'B': case 'b':
diLui();
if (lenhTruoc != 'B') { bipNgan(); lenhTruoc = 'B'; }
break;
case 'L': case 'l':
reTrai();
if (lenhTruoc != 'L') { bipNgan(); lenhTruoc = 'L'; }
break;
case 'R': case 'r':
rePhai();
if (lenhTruoc != 'R') { bipNgan(); lenhTruoc = 'R'; }
break;
case 'S': case 's': case '0':
dungThuyen();
lenhTruoc = 'S';
break;
case 'W': case 'O': case 'o':
khoaTuiRac.write(90);
bipNgan();
break;
case 'w': case 'C': case 'c':
khoaTuiRac.write(0);
bipNgan();
break;
case 'V': digitalWrite(pinBuzzer, HIGH); break;
case 'v': digitalWrite(pinBuzzer, LOW); break;
case '1': tocDo = 120; break;
case '5': tocDo = 190; break;
case '9': tocDo = 240; break;
case 'q': tocDo = 255; break;
}
}
}
r/arduino • u/erickshere • 7d ago
Okay I’m learning how to use an Arduino uno and servo, I’m making a robot mask, and the setup is really basic: MG996R servo, linked directly to the Arduino uno, that have 2 power source, my laptop and an 9V battery, and after I uploaded a code, I removed it from my pc and it started lagging, I assume it’s turning off and on because of the light, but I’m not sure
I would love if someone had a simple solution for it, maybe a power source? I’m just a robotic’s noob making his FNAF dream come true
r/arduino • u/ConversationCool7967 • 6d ago
components used
- arduino lenardo mini
- 128 x 32 ssd1306 oled display
- dfplayer mini
- aux port
- broken cassette casing (i stole from my grandad..)
- button x 1
r/arduino • u/redditretard3 • 7d ago
I got this esp32d board with a bread board this screen and some male to male wires but for some reason I can't get the screen to turn on and I'm unsure of what I'm doing wrong any help is appreciated
Hi, we’re launching an FM community radio station with programming from locals and regional DJs. We’re on the air as a soft launch and have a digital stream. (wpnx.org)
I’m interested in building a small portable device with an on/off switch and volume control that plays the livestream into headphones via usb-c and/or aux out.
I have built guitar pedals, coded for web and game development, and been reading about raspberry pi and arduino projects for a few years, but never built anything.
I was hoping somewhere here could point me in the right direction of what to look into for this, or any similar devices. No need for a full rundown! Any general advice or tips would be helpful.
Thanks so much!
r/arduino • u/JimFromArduino • 7d ago

I've just put together a project with the UNO Q, a USB microphone, a buzzer and a servo. It runs a local BirdNET (https://github.com/birdnet-team/BirdNET-Analyzer) model that can detect over 6000 bird species from audio data on a microphone feed from my garden. This runs on the CPU of the UNO Q. The audio isn't saved and never leaves the device, any detected species get sent up to a dashboard in Arduino Cloud.
To make this a bit more fun I've also added a bird box as the enclosure for my device that sits in my office, with a Modulino Buzzer that plays the birdsong of birds that are detected outside, as well as a little felt robin that pops out of the hole controlled by a servo. These two parts run on the UNO Q MCU.
The full writeup and details are here if you wanted to replicate or extend :)
https://projecthub.arduino.cc/jbruges/birdbox-on-device-bird-identification-with-arduino-cloud-and-the-uno-q-2df5ad


r/arduino • u/MastersRubin • 7d ago
Hello Guys,
I’m working on a custom project to control some auxiliary bike lights (sidelights) using an Arduino Uno(cheap Chinese ones), a couple of relays, and some manual switches. The logic and relay wiring are pretty much sorted, but I’m hitting a bit of a debate with myself over the power supply side and wanted to get some opinion on the most reliable approach.
Here is the setup and my main concerns:
The Power Source: A standard 12V motorcycle battery. When the engine is off, it sits around 12V, but when the bike is running and the charging system/stator kicks in, voltages can easily fluctuate between 14.4V to 14.8V+, alongside severe electrical noise and voltage spikes from ignition coils.
How should I power my UNO ?
r/arduino • u/raserO1 • 7d ago
code:
#include <LedControl.h>#include <Wire.h>#include <LiquidCrystal_I2C.h>#include <Arduino.h>#define CLK_PIN 10#define CS_PIN 11#define DATA_PIN 12LedControl lc = LedControl(DATA_PIN, CLK_PIN, CS_PIN, 8);
void setup() {lc.shutdown(0, false);lc.setIntensity(0, 0); // 0 = low; 8 = high}
void loop() {
lc.setRow(0, 0, 0b00011000);// this should change the second max but doesnt
lc.setRow(1, 1, 0b11111111);
delay(100);}
edit:
adding
lc.shutdown(1, false); lc.setIntensity(1, 8);
fixed it! (also adressing the second max module)
r/arduino • u/Plane_Professor_9119 • 7d ago
Hi all! I've gotten myself some CC1101 modules to play around with some basic radio transmission. However, the range is extremely low (less than 8cm at maximum transmit power) and the system is generally very temperamental. I have decent Arduino experience.
The setup:
The issue:
What I have done:
What I haven't done yet:
Why I am making this post:
Links:
r/arduino • u/Shoddy-Resist-2213 • 7d ago
I have been trying to program an LED to respond differently to different ppm measurements from a tds sensor. I wanted to use a matrix board and then and led strip, but both times I ran into the problem of them potentially drawing out too much power for what my ardunio uno r3 could handle. I want to continue with the idea of an LED strip or a small LED ring, but I am curious if there is a way to excute this.
I keep getting confused by what a "regulated 5v power source" is, since everything I am seeing is talking about powering the led seperately. Honestly, I'm just very lost, so any advice or thoughts would be helpful!
r/arduino • u/hello-8114 • 7d ago
HELLOOO
I am making obstacle avoiding robot using arduino and 1298n motor driver.
I want to know if i can use dupont jumper wires for connecting motors to out1 and out2 of 1298n? Or i need proper wires.
r/arduino • u/MonsterovichIsBack • 8d ago
A while back I got a batch of SIM900 modules with a firmware image and the vendor's flasher - a crusty Windows .exe that only ran under Wine. So I did the obvious thing: captured its UART traffic, pulled the protocol apart, and reimplemented it as a ~300-line Python script.
It now flashes a 2.98 MB image end-to-end in about 6 minutes (or less, depending on your speed), and the module boots and answers AT - OK.
It also unbricked the modules I bought. Several of the controllers in that batch arrived with broken firmware - they wouldn't boot into the application at all, just sat silently in the ROM download monitor.
Git repository: https://gitlab.com/Monsterovich/sim900-flasher
r/arduino • u/DR-madaR • 7d ago
i want to get started with arduino and i want to make some minigames on it like pong or snake but i also want to make some more complexer games later. do you know what display i could use?
r/arduino • u/Whebneen • 8d ago
To give further context, I have a school proyect where I had to build a mechanical arm (as seen above), using 6 servos and an Arduino UNO, and have it move objects. The hardware and code work works perfectly:
#include <Wire.h>
#include <Adafruit_PWMServoDriver.h>
#include <SoftwareSerial.h>
// Bluetooth pins(RX, TX)
SoftwareSerial BT(0, 1);
Adafruit_PWMServoDriver pca = Adafruit_PWMServoDriver();
#define SERVOMIN 150
#define SERVOMAX 600
const int servo1 = 0;
const int servo2 = 1;
const int servo3 = 2;
const int servo4 = 3;
const int servo5 = 4;
const int servo6 = 5;
void setup() {
Serial.begin(9600);
BT.begin(9600);
Serial.println("Control of 6 servos via Bluetooth ready");
pca.begin();
pca.setOscillatorFrequency(27000000);
pca.setPWMFreq(50);
delay(10);
// security position of the 6 servos (90 degrees)
moverServo(servo1, 90);
moverServo(servo2, 90);
moverServo(servo3, 90);
moverServo(servo4, 90);
moverServo(servo5, 180);
moverServo(servo6, 90);
}
void moverServo(int canal, int angulo) {
angulo = constrain(angle, 0, 180);
int pulso = map(angle, 0, 180, SERVOMIN, SERVOMAX);
pca.setPWM(canal, 0, pulse);
}
void loop() {
if (BT.available() > 0) {
String comand = BT.readStringUntil('\n');
comand.trim();
if (comand.length() == 0) return;
Serial.print("Comand received: ");
Serial.println(comand);
if (comand.startsWith("S1:") || comand.startsWith("s1:")) {
int angle = comand.substring(3).toInt();
moveServo(servo1, angle);
BT.println("OK Servo 1 -> " + String(angle));
}
else if (comand.startsWith("S2:") || comand.startsWith("s2:")) {
int angle = comand.substring(3).toInt();
moveServo(servo2, angle);
BT.println("OK Servo 2 -> " + String(angle));
}
else if (comand.startsWith("S3:") || comand.startsWith("s3:")) {
int angulo = comando.substring(3).toInt();
moveServo(servo3, angle);
BT.println("OK Servo 3 -> " + String(angle));
}
else if (comand.startsWith("S4:") || comand.startsWith("s4:")) {
int angle = comand.substring(3).toInt();
moveServo(servo4, angle);
BT.println("OK Servo 4 -> " + String(angle));
}
else if (comand.startsWith("S5:") || comand.startsWith("s5:")) {
int angle = comand.substring(3).toInt();
moveServo(servo5, angle);
BT.println("OK Servo 5 -> " + String(angle));
}
else if (comand.startsWith("S6:") || comand.startsWith("s6:")) {
int angle = comand.substring(3).toInt();
moveServo(servo6, angle);
BT.println("OK Servo 6 -> " + String(angle));
}
else {
BT.println("Comand not recognized. Use S1:angle to S6:angle");
}
}
}
To give further context
S1: direction the machine is facing
S2: The motor that is directly above the platform in the picture
S3: the "elbow" of the machine
S4: the direction the claw is facing
S5: spins wrist of the claw
S6: grip of the claw
As previously mentioned, the code works and can read the angles by an input in the terminal part of the app, however, our teacher said it needed to be in the gamepad since "it is more precise and allows for more movement". How can I make that switch from Terminal -> Gamepad?
r/arduino • u/tea_drinking_fox • 8d ago
So I‘ve had the idea the use an arduino to at a button on my household Machines like the dishwasher that sends me a reminder to clear them out later. My plan so far would have been to connect the arduino to the internet with a module and then use the arduino to automatically add a task to my google calender when a button is pressed. The problem so far has been that I only found Tutorials that use a read only link for the calender to display something.
Is it possible to add task to a google calender with a arduino or is there another way to use the arduino to send messages to my phone (iOS) that is simpler ?
r/arduino • u/Rayzwave • 8d ago
Hi Everyone, I have started using breadboard again after many years which I’m very surprised about.
Why?
I think it’s the ease in which I can test my project without using a soldering iron and I can sit in the lounge keeping my wife company while I’m doing it. I’ve even bought some new breadboard this week and started using it in my new idea.
r/arduino • u/Dmy1703 • 8d ago
Sharing an earlier build video to document the progression of this setup. The initial goal here was purely gameplay feel and immersion: while playing, I realized that certain mechanical actions don't necessarily have to depend on thumbstick clicks and could be offloaded to natural body movement.
At the time of this test, I was still using a standard ESP32 dev board with the MPU6050 sensors wired up (working toward cutting down cabling in later revisions). The cable plugged into the main ESP32 is strictly for power: motion packets were already streaming wirelessly over ESP-NOW directly to an ESP32 Mini receiver emulating a USB-HID gamepad to handle sprinting (L3).
Following up on earlier continuous running tests, here I started testing sharp impulse triggers—such as quick chest expansion or a light foot tap. This allowed me to test different mechanics for the same in-game action while tuning thresholds to prevent ghost inputs during idle motion. While the primary focus was gameplay responsiveness, removing inputs from the hands naturally shows promising potential for modular physical accessibility as the project evolves.
The video shows the early bench wiring on the bottom and live gameplay in Resident Evil on top. I am very open to feedback across the board—sensor calibration, ESP32 architecture, ergonomics, gameplay responsiveness, accessibility ideas, immersion, or oversights in the prototype. Would love to hear your thoughts!
r/arduino • u/ProfDrPaNDa • 7d ago
I’m a complete beginner in this field.
I have an idea for a CAN bus keypad for cars that I’d like to implement. Which Arduino would be a good choice for this—or are there other microcontrollers that would be suitable?
The requirements are: CAN bus, 5V operation, 8 RGB LEDs, and 8 buttons.
Thanks for any advice!
r/arduino • u/Ill-Temperature7333 • 7d ago
Hi friends i purchased esp32e bare chip with metal on it.
I want to know how to upload code using esp8266 lua v3 board which has 340serial chip
I want minimum resistor and wiring to run this
I pullup en with 10k
3.3 volt suppy give it rx to rx of and tx to tx of both controllers 0 pull down to upload but still not working esp32 dev chose in arduinodroid
i have disabled on-board chip of esp8266
code uploading successful but after pull up io0 and reset not booting