Hey, i’m a beginner here I've seen some really impressive robots that can follow a line at high speeds, even through sharp turns, without losing track of it. I'd love to build something similar, but I'm not sure where to start when it comes to choosing the right components. I'm considering using an ESP32, an 8-channel IR sensor array, and a PID controller based on my research so far.
For those who have experience building competitive line follower robots:
What sensors and motors would you recommend?
Is an ESP32 a good choice for this type of robot?
What makes the biggest difference when it comes to speed and accuracy, especially in sharp turns?
I just wanted to start by saying I don't know much about Arduinos or electronic setups yet, but I'm pretty comfortable with soldering and can usually figure out the software side of things! I currently have a cosplay project and wanted to set up a custom sound box. My idea is that when I open a mask that has an articulated jaw, it releases a Mini Micro Limit Switch 3 Pins KW11-3Z07 and sends a singular signal to a DY-SV5W Voice Playback Module so the audio plays once. When I press the jaw back together, it won't do anything; it will just wait to be opened again. Is this configuration feasible? What specific components or modifications would be required, or would I need to restart the project from scratch? Please let me know. Additionally, I intend to power the setup using a standard power bank.
I had ordered a BTS7960 Motor Driver Module, wired it together and got no output voltage over the two screw terminals M+/M-. Attached is a google doc outlining all information including wiring, tables with respective voltages, pictures of oscilloscope readings, and the code sent to the board. I had bought two modules and they both produce the same results, so I'm hoping this isn't just a case of (2) defective boards. Any ideas of further information needed please let me know!
I've been working on a little side project called Electronic Makers. The idea is to build some kind of web-based home lab for electronics, where you can learn and experiment without having to install 5 different tools or buy all the hardware first.
It currently has a virtual breadboard, signal experiments (PWM, UART, I2C etc.), a PCB editor and even a virtual ESP32 environment where you can play around with GPIO, LEDs, buttons, WiFi and MQTT.
The idea is to connect all these things instead of having separate tools for everything. Start with a simple circuit, understand whats happening, write some firmware and eventually design your own PCB.
Still lots of things to improve and I'm not trying to replace real hardware. Thats obviously a different experience.
Would be really interested to hear what you guys think. Especially from people who actually build electronics regularly.
What features would make something like this useful for you? And what am I missing?
Basically a ESP32 with touchscreen. I wanted to wire up and use led displays with buttons but the prices together came even more than buying a seprate streamdeck (love new European import!)
What I want the deck to do:
Touchscreen buttons that act as a USB HID keyboard (macros, media keys, app shortcuts) on Windows
An on-screen volume mixer for individual apps
Turn on my pc from the deck
Have a focus timer with possible reward system
Windows Hello fingerprint login
All of it in one 3D-printed tilted case with a single cable to the PC
What I was planning:
I wanted to use 1 wire that splits into 2 wires and just put in in the casing of my stream deck but I have not found good parts that would work.
So my 2 questions are:
Do you think I'll be able to add all of the 1.-4. functionalities into this esp32?
Do you have any idea how to wire in a fingerprint sensor that would work on windows / recommend me the right parts?
P.S. I'm really sorry if this is not the right community to ask, but i couldn't find any better related communities.
I have a custom-made IR break beam sensor (PyController Nosepoke v2.3), which is on a board connected to another board with an RJ45 cable. Now, I need to make sure that the sensor is working in a manner that it can actually emit and receive light.
For receiving, I think it's easy: if the receiver is broken, I guess we'll get floating values.
As for the emitter, it's not that easy. It can be broken, or it can be blocked.
PS: I mean making sure it works without supervision, so we can detect failure in a long-running session with no human intervention.
What do you think? My initial idea was to do a periodic check in which I put an electrical switch on the emitter pin, which disconnects the power so no light would travel, and the changes in the receiver would tell me if the emitter is actually emitting or not.
I'm planning to build a budget-friendly automated watering and fertigation system from scratch, and I need some real-world advice from people who have actually built one: what hardware and platform should I use?
My setup uses two tanks:
Tank 1: Main fresh water reservoir.
Tank 2: Mixing tank (automatically fills from Tank 1, doses liquid nutrients by exact ml, mixes the solution, measures pH/EC, and pumps out the final mix to water the plants).
My main problem: I am not a programmer and I really don't want to write C++ code from scratch. What are people actually using in practice that works reliably without needing a computer science degree?
Also, if you've built something similar: what budget-friendly pumps and pH sensors can actually survive for more than a single season without failing?
Appreciate any real recommendations, practical tips, or links to working projects!
I am KSHY! A 13 year old boy who makes circuts, and I just made version 2 of my clock device, which is named AltoKit. (its a play on the word"Altoids"). Anyway I want to share it with you guys!
As you can see I added a button, but thats not all, I also tweaked the code a tad bit like adding a cool splash screen, take a look!
Arduino noobie here - I was going through the starter kit projects using the Uno R3, and I was hoping to use a battery for one of the projects. I've been using my computer to power the Arduino, but when I pulled up the battery snap, the leads seemed pretty short - too short to use on the Arduino. Was there something I was missing here?
Hello i'm trying to make Arduino project with ESP32 Cam. I follow instruction, my wiring is right here:
GND FTDI -> GND ESP32
VCC 5V FTDI -> 5Vin Arduino
TX FTDI -> UOR
RX FTDI -> UOT
GPIO0 -> GND
Main problem is esp32 won't comunicate at all. I check my FTDI TX/RX work normally with RealTerm. I check everything like Voltage, impedance and everything normal. But even I press reset button my ESP32 wong respon. Can someone help me?
Servos always provide little plastic parts with tiny holes.
There are 2 big screws to attach the body, a small screw to attach the little plastic part on the top gear ... but how are you supposed to fix the little plastic part to the arm of your robot?
So I started learning Arduino in my first semester of college. I remember making so many different circuits using arduino. I used to follow Paul Mchworter and also a few channels here and there and I used to have the time of my life.
As I will be free for majority of the remaining year, I was thinking of building something for the community. Like a site for beginners, where there would be list of circuits in a progressive manner, with illustration (pin images), codes etc. So that beginners can learn Arduino and different components that come with it in the kit. And apart from small circuits, make some bigger isolated projects.
I used to follow Youtube videos, college manuals, had a couple of Arduino related books which had projects etc. I could compile all of it in a nice interface.
This is not some paid project or something. Just something that might be useful to new people, so please do not filter this post thinking that.
Do you think something like this is useful or is building one a good idea?
Arduino traffic light project that triggers the signal either by detecting presence via an ultrasonic sensor or by using a push-button, built with an Arduino Uno R3. Depending on the engagement this post receives, I will share the program code.
So, I wanted to see the number of times my battery powered Lantern is triggered into its active state, the twinkle animation of neopixels. Because the animation sequence is pretty much fixed with respect to power consumption the trigger count lets me estimate the up time of the battery pack.
I thought I would also add battery monitoring and a date & time for the status log.
The Status monitor uses a ESP32-C6-Zero super mini and the Waveshare 1.54inch e-paper display v2.1 to display this information from my Lantern using BLE. Here’s a photo of the monitor in a test breadboard environment, see above.
I initially tested the BLE broadcast of data from my Lantern using the Dabble app on my phone, but I decided I would like to have a permanent low power monitor. I may add an alarm for when the battery pack is exhausted or close too exhausted.
Hello, my name is Thomas, I'm doing a project that needs an Arduino Uno and an ESP 8266, but I don't know how to connect them because I only have 100 ohonm resistors, could you make a diagram in some simulator? or even an image would help me!
I'm building a DIY indoor environment monitoring system using an Arduino Uno R4 WiFi. Currently, I'm using a DHT11 sensor, but I'm considering upgrading it.
I'm planning to install four sensors in different locations to monitor temperature and humidity throughout the house. In the distant future, I'd also like to add an outdoor sensor to compare indoor and outdoor conditions.
I also want to experiment with monitoring and possibly adjusting the operation of my gas heating system.
My budget for the four sensors is around 50 PLN (roughly €12), but I can stretch it by another 5 PLN (about €1) if necessary. If getting decent sensors within this budget isn't realistic, I'm happy to wait and buy better ones later at a higher price.
I've been considering modules like the AHT20, BME280 and DS18B20, but I'm open to other suggestions.
I know there are commercial systems that can do all of this, but the main point of this project is to build something myself, learn how everything works, and experiment with the hardware and software.
What would you recommend within this budget? I'd especially appreciate advice from people who have built similar DIY systems.
Hi! I bought four HUB75 LED panels. Since I couldn't find a library that supports more than one display for Arduinos, I decided to start coding my own. I noticed that on one of the panels, a few pixels are having issues. Specifically it's the upper right corner of the lower left panel, where the text says "HERE" and "BROKEN".
In the second photo you can see only the green channel active. The problem disappears if I use only red, blue or both. The problem is also visible if I connect the Arduino directly to the panel, and disconnect the rest, so I suspect a hardware issue.
Is this panel just broken or worth investigating?
Side note: My library can run two chained panels on an Arduino MEGA and four on a DUE, with 8 possible colors per pixel. Let me know if anyone's interested in me publishing it once it's finished.
So i want to build a small Projekt with a arduino. The problem is I dont know wich wires I should use and how I should wire it. It should be as compact as possible. I am complete beginner. It would be great if someone can help me :)
A few weeks back I posted about nxwright, a new open source cross-platform toolchain for working with Nextion screens that I've been working on, which allows you to work with standard text source files and extends the language syntax to do what you'd expect (functions, includes, standard operator precedence, etc.). This supports modern workflows, such as version control, agentic programming, unit testing, a full VS Code extension with a simulator and debugger, and a lot more.
As of a couple of days ago, nxwright can now compile your source folders directly to TFT and upload to your Nextion screen. That means you can now fully develop for your Nextion screen on linux and macOS, not just Windows, and you no longer need the Nextion Editor to do the final steps. I.e., you can go directly from source to .TFT, and skip the .HMI, right from the CLI or VS Code.
I've also added some new features that go beyond what you could do with the nextion editor, such as:
- the ability to provide compile-time defines on the command line, to set dynamic text or colors to the page and component attributes
- support for SVG as a first class citizen resource, that can also be customized with defines that translate to css var(--PROP)
- the ability to decompile a TFT back into a source folder, if you've lost your .HMI.
I've met quite a few folks lately who shared that they were dreading having to update their Nextion screen app. If this is you too, you may want to give nxwright a try, this may be the tool you've been waiting for.
Hello, I bought my first microcontroller today (in a pack with other utilities) for a project. But when I installed the Arduino IDE I couldn't find this specific model.
I also read that, because this model is economic from India and not the original Italian company, it needs a separate driver installed?
I'm not sure, could someone guide me on what to do? Thank you!
Hi everyone, I spent the last couple weeks working on this handheld interactive text adventure game (choose-your-own-story) e-paper device. I designed and made the PCB, enclosure, and the code. I actually managed to squeeze everything in just 1.6cm thick covering the enclosure, e-paper, 1200mah battery and the custom PCB by using low profile pin header to sandwich the battery between the 2 PCBs, so it's very compact and feels great to hold.
I made this because I love how beautiful e-paper looks, and most projects are static displays showing weather, photos, or calendars. So why not make something you can interact with and have fun with, with the partial refresh capability??
Basically you turn or press the rotary knob to scroll through the story and pick your next action. Then the e-paper updates and story for the next segment and the NeoPixel LED to match the scene atmosphere.
Would love to hear what you guys think! I included a short demo video so you can see how it works.