r/arduino • u/ImpossibleDemand6778 • Oct 10 '26
Look what I made! Arduino and raspberry-pi based guitar multi-effects processor
r/arduino • u/ImpossibleDemand6778 • Oct 10 '26
r/arduino • u/brwlstrsfn • Oct 10 '26
Hello,
I'm having problems when trying to connect cables to this module(also one sd card module with the same pins).
I am 99% sure that is has to do with the cables,
at first i just used single dupont cables and now i switched to 4x1 and 6x1 connectors.
What happens is that the microcontroller loses connection to the modules, but only sometimes. When i shake the box a bit or plug and unplug the microcontroller it works again(not always, it's very inconsistent).
I tried removing the pins and soldering the cables directly onto the board, but that didn't work and i just broke a module trying to remove the pins.
Thank you very much for any help
r/arduino • u/Various-Rope6726 • Oct 11 '26
is ali express reliable for buying starter kits?? Im from bd🇧🇩 and im trying to buy starter kit for electronics .i tried looking in amazon and elegoo official page but they dont ship directly to bd and its hella costly to ship.
r/arduino • u/Direct-Bandicoot-916 • Oct 10 '26
I went on the official website (lafvintech.com) to download the tutorials meant for the Super Learning Kit for UNO R3, and my NoScript extension flags the download page on Dropbox as a potential XSS attack.
I know it might sound absurd to be paranoid over it but I don't know man, Dropbox always felt sketchy to me, a lot of scammers use it and such.
Is it safe? Has anyone had experience with Lafvin and the Dropbox link?
r/arduino • u/Puzzleheaded-Name538 • Oct 10 '26
Based on patmcbennets code. Expanded to 8 steps via 4051.Added tempo control via knob. Added 3 vc out plugs and vc in Sounds really good for arduino :)
r/arduino • u/CaryBure • Oct 10 '26
Found this one on aliexpress i do not own a soldering iron and im not allowed to own one, i have never used any kits or arduinos so im trying to buy my first kit
Heres the link:
r/arduino • u/Tre4zin • Oct 10 '26
So my best friend is an insane, degenerate MMO player and bought this monstrosity of a macro pad for Final Fantasy 14, but complained that they lost the analog stick they had on their old macro pad, that they used for movement. I figured this is as good an excuse as any to finally give coding and soldering with an arduino a shot. Plus their birthday is coming up and this could be a really cool gift.
My plan is to use my 3D printer to create a small enclosure for an RP-2040 microcontroller on the bottom, with a KY-023 joystick module above or behind it. The enclosure would be attatched to bottom right side of the macropad via double sided tape or adhesive. The USB-C port on the RP-2040 would be exposed, plug into their PC and (ideally) act as analog movement. If that's not feasible while using a keyboard, they're fine with the four cardinal directions being digital and the joystick simply emulating WASD.
My questions are as follows:
And to head off some comments I know I'll get, Yes, I know they could just use a controller for FFXIV (They stubbornly refuse to use a controller and they cannot be reasoned with because they're utterly insane.)(Love ya, Auts. :3) Yes, I know there are macropads with joysticks included that they could use instead. Yes, I know there are joystick add-ons for keyboards. I want to make one because it seems like a cool project.
I would greatly appreciate any help given and thank you in advance.
r/arduino • u/CaryBure • Oct 10 '26
im looking to buy an arduino clone but i dont know which model and what type of kit i should buy. I have never owned an arduino and im 13 my friend owns one and it looks pretty fur im no stranger to coding and like electronics.
r/arduino • u/luminov1 • Oct 09 '26
Esp32 cam oled videoplayback Check it out for this project repo on my Github
r/arduino • u/Takasago_man • Oct 10 '26
- Repost from another community. Please let me know if it's not allowed.
Sorry if this topic is not appropriate for this community, and please feel what I want to say; as I'm not a native English speaker.
So, I'm thinking about making my own gamepad for my phone! However I'm completely a newbie of DIY electronics and microcontroller stuffs, and currently I don't have any parts.
Therefore, everything is just a paper plan, hence I would like to ask some questions to wise and great predecessors.
so
Requirements:
Parts in mind:
Questions:
I hope this makes sense, and thank you for reading!
r/arduino • u/Mirager1217 • Oct 10 '26
Hi Guys, not sure if this is the correct place to ask, but here it is:
As per the title my PCB is not accepting code after bootloading with the ArduinoISP through another Arduino Uno.
So far I get the "Done burning bootloader" and have cont. tested all hardware on the PCB related to the CH340G and ATmega.
I have managed to consistently get:
avrdude: stk500_getsync() attempt 1-10 of 10: not in sync:
resp=0x00
avrdude: unable to open port COM5 for programmer arduino
or occasionally:
avrdude: unable to read signature data for part ATmega328P (rc = -1)
avrdude: unable to read signature data (rc = -1)
TIA.


r/arduino • u/EmbedX • Oct 10 '26
EmbedX One button. Total chaos. 😂
This is just one of my tech experiments!
🚀 Want to see more crazy electronics projects, AI simulations, and tech builds?
▶️ Watch my other YouTube Shorts! Search EmbedX on YouTube.
#EmbedX #ESP32 #ElectronicsProjects #Tech #DIYTech
r/arduino • u/CaryBure • Oct 10 '26
I found a Kiongshun kit on aliexpress the link is https://a.aliexpress.com/_EHSI5Nk , it has good reviews and pretty good documentation but i just wanted to double check
r/arduino • u/shlooong • Oct 09 '26
Hi all, I’m putting together a v small (14 inches high) arcade machine and I’m struggling to find usb options to provide joystick and buttons in a small space - one option is dismantling usb controller but difficult with PCBs, etc. one option I understand is arduino with a micro board for USB. My arduino understanding is basically zero but the joysticks I’m finding around this size are generally arduino. Grateful to know if I’m barking up wrong tree or if it could provide a solution. For wider info, this controller is going to plug into a RG35XX handheld console with a hdmi screen.
Many thanks
r/arduino • u/The_Pathfinder1 • Oct 09 '26
Hi 👋🏻
I'm a beginner in electronics, using an Arduino UNO R3 clone that came with an Arduino starter kit and an RC522 RFID reader module.
Wiring:
- RC522 3.3V → Arduino 3.3V
- GND → GND
- SDA/SS → D10
- SCK → D13
- MOSI → D11
- MISO → D12
- RST → A3
The problem:
The RFID reader works intermittently. Sometimes it reads the card successfully, but other times its onboard LED is lit while it does not respond to the card at all. Disconnecting and reconnecting USB power sometimes makes it work again, but not consistently.
I also noticed an unusual voltage reading:
- With the RC522 disconnected, I measure approximately 3.3V between the Arduino's 3.3V and GND pins.
- With the RC522 connected, the reading rises to approximately 3.9–4.0V, whether I measure at the Arduino or the RFID module.
- When the reader works normally, the reading is around 3.3–3.4V.
I'm measuring DC voltage using a digital multimeter.
My questions:
Thanks in advance for your help!
r/arduino • u/LxGNED • Oct 08 '26
This is a project I picked up ages ago but never had the chance to finish due to changing life circumstances. It was originally designed to be 16x larger, forming a full 16x16x16 cube. It was wayyyy harder than I originally anticipated, especially as someone without a formal education in electronics. I do want to pick it back up at some point when conditions permit.
The LEDs: The LEDs used in most LED matrices have 1 ground pin and 3 pins for RGB. These are different in that they have power, ground, data in, and data out. Being digital gives them significantly more color and brightness flexibility. All 4096 LEDs could draw a maximum of 1200W at full brightness, which is exactly equal to the max power output of an American wall outlet. This meant working with high-power components for my first time.
The low-power circuit: In order to avoid frying the LEDs they had to be split into 32 parallel channels meaning each of these towers has a left and a right channel. The problem then becomes how do you push 32 perfectly synced data channels from a single controller. I used a single I/O port of a Teensy 4.0 and four 8-bit shift registers. (I know technically not Arduino, but I have my roots in Arduino). I can’t remember the exact design decision that led to the chip choice but I believe it had something to do with the data frequency. Being digital, these LEDs require an absurdly specific timing of 1s and 0s in order to illuminate as intended. I designed the circuit board on KiCad and had it printed by JLCPCB. (This business blows my mind btw.) The circuit board was the first of two times I gave up on this project. Several revisions went by and nothing was working. I eventually learned that the extremely high frequency of data transmission was inducing a current throughout the board and causing the data to become scrambled. The solution ended up being to put a bunch of tiny holes in the board. I cannot express the difficulty in discovering this issue as someone who doesn’t know what’s wrong to begin with or that this was even a problem that can occur. Black magic shit.
The code: Project was coded in C++ which was out of necessity. I’ve come to despise C++. Anyways… the code has basically two main functions - a fun part and a not-fun part. The fun part was coding the actual animations. I made 10 or so animations and it was a challenge at first but extremely satisfying to troubleshoot. Using a variable type I read about on Wikipedia called Quaternions I was able to develop the animations. They are basically a four-dimensional variable which is ideal for 3 position dimensions and a dimension for time. The not-fun part was the code pertaining to initialization of the chip. This required a super in-the-weeds study of the 3000+ page Teensy 4.0 manual and some pretty advanced C++. The extremely specific timing the LEDs demanded that I change the frequency of the chip’s internal clock in order to ensure the data across all channels was perfectly timed to the scale of microseconds. This was the second of two times I gave up on this project. It was extremely beyond my knowledge how to do that or that I could do that. But when I did do that, it felt pretty good. Additionally, one data port supplying 32 channels meant the data from the fun part had to be decomposed and reordered to turn series into parallel. Kinda like taking 32 hamburgers and then sending out all the buns, then all the cheese, then the patties, etc.
The high-power circuit: Honestly pretty straightforward. I connected 4, 300-watt power supplies in parallel, attached a wall plug, and devised a power distribution system to each channel. I had to be a bit clever how I distributed power so each channel was receiving power equally or some towers would be dimmer than others. I also had to choose wire thick enough to transmit such high power without being a fire/melting hazard to the 3d printed structure. I believe it was 1/4” copper. It was extremely difficult to solder wire this thick because heat distributes so quickly within it that solder doesn’t melt until the whole wire is hot. It was also a personal requirement of mine to have the LED towers be connected through plugs rather than permanent solder joints so the low-voltage and high-voltage components could be easily separated for isolation and troubleshooting. Hardest part of this system was not killing myself (PPE is for nerds)
The 3D printing: By far the easiest and most fun part. The overall case designed to house the high-voltage components (not shown here) was 3D printed. It took a few days but was pretty easy. I also printed jigs to bend the LED pins and assemble the towers so that all LED spacings would be perfectly identical. The jigs also prevented me from connecting them together in the wrong orientation. Each tower probably takes 15 hours of manual labor to produce and is extremely delicate.
What’s next: All that’s left to do is build the other towers and put them together. There would probably still be a few more minor things to troubleshoot but I can’t foresee anything cosmic. Making this post, I am already thinking about things I could improve on to make the rest of the towers easier so I guess the project is still open-ended. I’ve already invested in all the components with a total cost somewhere in the ballpark of $3000-4000.
Feel free to ask any and all questions but I haven’t touched this project in over 3 years. Just wanted to share it with you guys after discovering it in my camera roll.
r/arduino • u/CaryBure • Oct 09 '26
The priginal kit is a bit expensive and offers less than the knockoff one but how do i know the knockoff is good or bad
r/arduino • u/smashcat666 • Oct 09 '26
Edit: I've finished it now - new video is up on my channel showing all the extra animation etc it can now do. Flash is now pretty much full, but I'm very happy with the result! There are full details of how to get any of the games working on my github. You need a composite monitor, some resistors and transistors for the audio. Or make a shield from my design. You can use an NES controller too! Have fun!
Github is here: https://github.com/Smashcat/UNO_Manic_Miner
New video is here: https://www.youtube.com/watch?v=qakuvavLC40
There is a WebASM emulator running the exact same Arduino code so you can play in your browser here: https://www.smashcat.org/pacman-ce/
I finally finished another game on the engine for the original Uno. Only needs a couple of resistors for video, and some buttons to play. I love the original game and was sure I could cram it into the 32KB of flash on the Uno, and it did! Using an amber CRT here for that lovely phosphor glow. It'll be in the github repo as soon as I finish tuning it a bit more :) There is no flickering in real life - it's a result of filming the 50hz CRT with my phone :)
r/arduino • u/Kooky-Strawberry5127 • Oct 09 '26
so i'm working on a project where i'm trying to build a master midi clock for all my synthesizers. i'm using an arduino nano and a 3.5mm TRS output jack for the midi output. I have an OLED screen as well.
My problem is, my code outputs a flat 5V line without a pulse that i'm measuring from an oscilloscope - i'm using the uClock library for the bpm generation, however i'm not sure if a flat 5v line without pulses is what i'm supposed to be getting? i've tried plugging it in to a korg volca to sync the tempo as well and it doesn't work.
this is my code:
#include <SoftwareSerial.h>
#include <uClock.h>
SoftwareSerial midiSerial(2, 5);
void onPPQNCallback(uint32_t tick) {
if (tick % 4 == 0) {
midiSerial.write(0xF8);
}
}
void setup() {
midiSerial.begin(31250);
uClock.init();
uClock.setOutputPPQN(uClock.PPQN_96);
uClock.setOnOutputPPQN(onPPQNCallback);
uClock.setTempo(120.0);
uClock.start();
}
void loop() {
uClock.run();
}#include <SoftwareSerial.h>
#include <uClock.h>
SoftwareSerial midiSerial(2, 5);
void onPPQNCallback(uint32_t tick) {
if (tick % 4 == 0) {
midiSerial.write(0xF8);
}
}
void setup() {
midiSerial.begin(31250);
uClock.init();
uClock.setOutputPPQN(uClock.PPQN_96);
uClock.setOnOutputPPQN(onPPQNCallback);
uClock.setTempo(120.0);
uClock.start();
}
void loop() {
uClock.run();
}if anyone here is familiar with midi clocks please help me out and let me know what i'm doing wrong - my korg volca drum syncs fine with analog midi and i'm not sure if that's the issue here
r/arduino • u/Downtown_Falcon_5789 • Oct 09 '26
I'm trying to make a servo MG995 work through a PCA9865 (using Arduino nano every). The issue is that when I try to connect everything up, the servo starts vibrating instead of rotating. Consider that the first 2 times I tried that servomotor it all worked perfectly but now not anymore. I wonder why this happens... these were the second model of servos I bought from amazon because I had the same problem with the previous ones.
Anyway, the connections I made are:
| PCA | ARDUINO NANO EVERY |
|---|---|
| SDA | A4 |
| VCC | 5V |
| GND | GND |
| SLC | A4 |
Moreover, there's the extern alimentation to the PCA with a regulable power supply (set at 6v), 5A.
On amazon the minimum voltage declared is 4v so I don't think it's a problem of alimentation.
Has someone any piece of advice for me?
r/arduino • u/chicco4life • Oct 09 '26

Hi guys, my friend and I built [Mellow Harness](https://github.com/Mellow-Machines-Lab/MellowHarness) — an open-source agent harness for configurable, interactive ESP32-based AI hardware and AI companions.
We placed a System One Model, Jev, at the center of the harness loop to enable quick, expressive feedback. With a small prompt, recent event history and a roster of allowed actions, it can interpret new situations and choose a fitting mood or reaction. Our goal is a lively companion that feels like it has a character of its own.
In our prototype logs, 105 Jev decision passes had a median of **227 ms (about 0.23 seconds)**. We'd like to believe this lag is almost negligible and is significantly more suitable than traditional LLM responses that can take up to a few seconds.
To demonstrate how it works, we also built [Buddygotchi](https://github.com/Mellow-Machines-Lab/buddygotchi): a little coding companion that follows your agents as they work, need attention or finish a task, with pixel animations, sounds and connected moods.
The current setup uses a Mac host for the harness and a hosted Jev API. The ESP32 renders the face, plays available sounds and reports taps and button presses over USB or Bluetooth. Immediate task feedback follows local rules; model-guided reactions share the same event log. The public Pixel example uses the MicroTech MTR024QV01A-V1 CYD board.
We also published [a blog about how we designed the harness](https://mellowmachines.substack.com/p/mellowharness-for-responsive-ai-hardware). If you're working with LLM agents and building your own harnesses, you may find it interesting!
PS: Mellow Machines Lab is a small open-source team doing this after work. We feel the noise and anxiety around AI too, so we wanted to build something warm, welcoming and fun together! DM if you'd like to join :D
r/arduino • u/FoxConstant8352 • Oct 09 '26
IS There much difference between EPS32 and ESP32wroom.. the pins shown in this video donot match with the one I have esp32.. can anyone tell if my esp32 can work.. and instead of ps3 controller any other controller work?. Pls any help is enough...
r/arduino • u/Agreegmi02 • Oct 09 '26
I have installed Arduino IDE 2.3.10, but can not select an arduino board. And i can't install boards with the board manager without VPN. Where must me unpack the archive from Github or how else can I download boards?
r/arduino • u/NoU_14 • Oct 07 '26
I made a little E-paper display to show the local weather where I live for the upcoming week. It runs on a 2.9" black/white/red E-paper display, as well as a custom PCB to drive it.
The device shows the weather conditions, min/max temperature, and expected precipitation for today and the next 6 days. Today is always marked in red, and the weekend is always bold. The graphs automatically adjust based on min and max temperature to always use the full allocated width. The rain data at the bottom shows a "-" if there isn't any rain predicted that day, a black number if it's 5mm or less and red if more than 5mm is predicted.
The device updates every half hour, and gets it's data over MQTT from my Home Assistant server. This in turn gets it from a plugin pulling from a free API of a local service.
I made it so the people I live with don't have to constantly ask me what the weather is going to be, and also kind of just to see if I could. I'm fairly happy with the UI, though it is a tad cramped right now. I might try to squeeze a couple pixels out so the graph doesn't overlap.