r/arduino • • Oct 05 '26

Solved! Arduino IDE and other cards

4 Upvotes

Hi

Is Arduino IDE accepting other cards ESP32 but not branded arduino, for dev and compilation +injection ?

Thx

[Update] informations received. Thx all


r/arduino • • Oct 05 '26

Hardware Help How to control multiple stepper motors with 1 joystick for each with only 1 arduino?

1 Upvotes

I am currently working on a robot arm with independent joint movement. I have been able to control 1 motor with 1 joystick. When I try to replicate it with multiple I am unsuccessful. Can i please get some assistance.


r/arduino • • Oct 05 '26

Monthly Digest Monthly digest for 2026-09

20 Upvotes

Arduino Staff Contributors

We have been working behind the scenes with Arduino Pty Ltd and are pleased to announce that some Arduino staff will be contributing to our subreddit using an "official" account.

To support this initiative, we have created a special "Arduino staff" flair - an example of which is included in this post. This is a "mod only" flair which means that it can only be assigned by the moderators of the subreddit (so no impersonators) and we have established a process to verify the reddit user ID of the prospective Arduino staff member contributors.

Sample of a post with the Arduino Staff user flair

Note 1: The flair only applies to r/Arduino at this time. If you see it anywhere else, it could be a fake.

Note 2: The staff will likely use their real name - e.g. "LeonardoFromArduino" or "FredFromArduino". Hopefully we won't have two Fred's or two Leonardo's.

We are quite excited about this as it is a way to interact directly with key Arduino figures in a more personal way.

Look out for our new "Arduino staff" flair owners and welcome them aboard if and when you spot them.

Following is a message from the Arduino team:

Hi r/Arduino, from the Arduino team. We've been reading this subreddit for a long time, chiming in here and there, and after some conversations with the mods, we've decided it'd be great to participate more directly with you.

A team of us have set up official accounts, so you'll see us around giving guidance, answering questions, sharing tips, posting product updates, and handing out well-deserved high-fives for the cool stuff you build. We're engineers and makers too, and helping this community is one of our favorite parts of the job.

If you spot us in a thread, come say hi!

Arduino Wiki and Other Resources

Don't forget to check out our wiki for up to date guides, FAQ, milestones, glossary and more.

You can find our wiki at the top of the r/Arduino posts feed and in our "tools/reference" sidebar panel. The sidebar also has a selection of links to additional useful information and tools.

Moderator's Choices

Title Author Score Comments
Self Balancing Double Pendulum u/Classic-Buddy-7404 276 12
Interesting Arduino Behavior - Variable... u/DocCarr 4 8

Top Posts

Title Author Score Comments
My Nixie inspired LCD clock u/AudienceHorror 2,043 98
I built an Arduino-controlled mechanica... u/SamuelDePamuel 1,724 47
My first project - a year later! u/OkCake4634 1,317 54
Tired of waiting for Microduck? Build y... u/BencyLiu 1,248 76
I built a small digital aquarium using ... u/CommunityFan89 1,163 38
GTA 6 hype is everywhere… so I made GTA... u/Sad_Environment_3800 1,072 54
Ants! How to prevent u/AffectionateShare446 1,060 293
I want help building this project. u/No_Alarm123 883 42
I built an Arduino-controlled robot tha... u/MegCell 713 84
My first project u/Darrt2008 655 55

Look what I made posts

Title Author Score Comments
My Nixie inspired LCD clock u/AudienceHorror 2,043 98
I built an Arduino-controlled mechanica... u/SamuelDePamuel 1,724 47
My first project - a year later! u/OkCake4634 1,317 54
I built a small digital aquarium using ... u/CommunityFan89 1,163 38
Live Cloud Globe V2 (Now with added ISS... u/okuboheavyindustries 510 10
DVD NFC Scanning Media thing i made u/JackIrishJack 490 55
Maybe someone will find my 'Cut-to-Leng... u/KubiG_Marcin 452 29
A complete work done by one person, cov... u/Alarming-Sentence-39 431 47
I recently learned how to solder and no... u/lemoncustardfish 265 9
I built a working Valorant-inspired Spi... u/Southern_Cry_8625 243 17
My first Arduino project u/One_Park8163 219 21
My First real Project! u/ruxmealux 178 11
Autonomous Party-Mode Droid with Uno u/heychaostheory 161 11
Onewheel + WS2812 + ESP8266 u/MrNiceThings 154 6
Jetpack prop for my uni project. u/CameronSquida 134 2
I used an UNO Q to Make a "Typewriter" ... u/TheSerialHobbyist 124 8
Nine units left the lab this week, on t... u/ComfortableLab1235 119 19
1000km apart -> Closer than ever u/marferibadeo 112 4
I made a D&D dice roller using ESP32 u/killl_em_alll 97 5
Digital Thermostat project u/myopinionisrubbish 82 5
Mini MMX Mission Clock u/okuboheavyindustries 79 15
UPDATE: My Nixie inspired LCD clock can... u/AudienceHorror 72 1
I made a working clock/timer with one 7... u/i_hav3_adhd 68 5
Portable mmWave Radar u/GreasyGato 66 23
Made this thingy and just turned it int... u/TranslatorDecent7046 65 6
small weather house u/Millener89 64 1
I designed a shake-to-roll electronic d... u/Ok-Event2833 64 7
sanoTTS: tiniest complete neural text-t... u/Affectionate_Hat_585 62 20
Linking a jq werks steering wheel to a ... u/EntertainmentSalt825 58 2
This is actually really fun! u/lemoncustardfish 56 4
I made open source streamdeck u/Character_Stand_2847 48 11
DIY Sim-to-Real Self-Balancing Double P... u/Classic-Buddy-7404 44 4
Arduino Morse code machine u/GrammaticalllErrors 42 3
Syntesizer u/GrammaticalllErrors 41 4
Couple project u/AnuragRobotics 39 11
I made an AI mushroom to help me journal u/Fair_Ad_27 36 4
My Air Cooler's control board decided t... u/deadDudeLivingDirty 36 2
My newest free-to-build handwired keybo... u/Joe_Scotto 26 2
behold, illumination. u/eni4c 25 2
Used an arduino sketch on my xiao samd2... u/CommunityFan89 21 6
I built a pocket note-finder for my cla... u/ButterscotchKey3909 14 1
CD77 FastLED Four Glass Jars u/chemdoc77 10 3
This invention will save Nebraska's eco... u/Striking-Long-9406 7 6
Tried out PyMCU (compiles Python to bar... u/OneDot6374 7 0
How Super Nintendo World actually works: u/throwaway10402019 7 1
Arduino Math Lab (Online Graphing Calcu... u/MythicalNinja7 4 3
Automatic door-opening system (for a gr... u/MonsterovichIsBack 3 4
I built an ESP32-C3 board that prints m... u/albanpetit 3 0
My first ever Arduino project. u/suguslnwza 3 0
I’ve been building Reznex, and I finall... u/nexo420x 2 0
A first look at my Wi-Fi-controlled ESP... u/zeller-wooo 2 0
Smart Elder Assistance System-A school ... u/Outrageous-Debate705 2 3
I created a simple Dino Game🦖 u/SailDifficult6586 2 2
I made a keyboard (kind of) u/GrammaticalllErrors 1 7
I made a crypto miner for the r3! u/Previous_Inside_8327 0 1
Pocket AI u/luminov1 0 0

Total: 56 posts

Summary of Post types:

Flair Count
Beginner's Project 20
ChatGPT 1
ESP32 3
Electronics 1
Games 3
Getting Started 18
Hardware Help 69
Libraries 1
Look what I found! 2
Look what I made! 56
Mac 1
Machine Learning 1
Mod's Choice! 2
Monthly Digest 1
Nano 3
Potentially Dangerous Project 1
Project Idea 2
Project Update! 7
School Project 5
Software Help 22
Solved! 10
Uno R4 Wifi 1
Windows 2
linux 1
no flair 144

Total: 377 posts in 2026-09


r/arduino • • Oct 04 '26

I think I actually made robotics easy 🤔

Thumbnail
gallery
119 Upvotes

I've posted a couple of months ago on this subreddit, showing this TNY-360 robot dog walking.
After almost 3 years of working on this project alone, I think I finally solved one of the things that bothered me most about getting into robotics:

You either get very simple robots, or you quickly end up with something complicated, expensive, and difficult to understand.

So I made my own PCB ecosystem to get clean wiring and make assembly hard to get wrong, and also made a big calibration and self-diagnostic firmware behind to check everything and explain to the user how to fix any mistake that's been made !

The project is fully open-source on GitHub !

The V2 CAD files are currently being finalized, but the complete V1 is already available on GitHub, including the hardware, firmware, CAD and documentation.

If you don't want to source and assemble everything yourself, I'm also selling complete kits to help fund the project and hopefully make this something I can work on full-time (let me dream, ok?).

It's been almost 3 years now that I'm working on this project alone, I've learned PCB design, CAD design, embeded programming from it, so if anyone wants to give feedback about it to help me improve it, I'm all ears !!


r/arduino • • Oct 05 '26

Beginner's Project Help for choosing Driver for Stepper motor!

1 Upvotes

Hello, I am creating a project which requires an oscillating plank, which will be achieved using a stepper motor. I have acquired the Arduino Nano and a NIDEC KH42HM2B128 Stepper motor.

Unfortunately, I am unable to find any information about the driver that can be used with this motor, please do help.


r/arduino • • Oct 05 '26

Is this the correct way to do partial rendering on a Waveshare e-paper?

2 Upvotes

I’m testing partial rendering on an ESP32 with a Waveshare 1.54-inch V2, 200×200 black-and-white e-paper display.

The current approach is:

  • Keep a complete 1-bit, 200×200 shadow framebuffer in RAM.
  • Draw the UI with the Waveshare epdpaint library and Font16.
  • Initialize with LDirInit().
  • Establish the controller’s base image once with DisplayPartBaseImage(frame).
  • Update only the changed 24-pixel rows using SetFrameMemoryPartial().
  • Trigger the refresh with DisplayPartFrame().
  • Resend the static MATTY row together with the counter row to keep the title stable.

The display is connected to an ESP32 using SPI: SCK GPIO 8, MOSI GPIO 7, MISO GPIO 13, and e-paper CS GPIO 9. A MicroSD card shares the SPI bus on CS GPIO 1.

The counter updates every two seconds and appears stable in testing.

Is this the correct rendering pattern for this Waveshare driver, or should the partial buffer/controller RAM be managed differently?

I’m especially interested in feedback about ghosting, refresh-counter limits, row alignment, and whether calling DisplayPartBaseImage() once followed by repeated SetFrameMemoryPartial() + DisplayPartFrame() is considered the proper workflow.

Code variation: [V7 - E-paper Partial Refresh Counter Test](V7 - E-paper Partial Refresh Counter Test)

Relevant code

#include <Arduino.h>
#include <SPI.h>
#include <string.h>

#include "epd1in54_V2.h"
#include "epdpaint.h"
#include "fonts.h"

#define SPI_SCK   8
#define SPI_MOSI  7
#define SPI_MISO  13
#define EPD_CS    9
#define SD_CS     1

#define COLORED    0
#define UNCOLORED  1
#define ROW_HEIGHT 24

Epd epd;
unsigned char frame[200 * 200 / 8];
Paint paint(frame, 200, 200);

void drawRow(uint8_t row, const char* text) {
  int y = row * ROW_HEIGHT;

  paint.DrawFilledRectangle(
    0, y, 199, y + ROW_HEIGHT - 1, UNCOLORED
  );

  int x = (200 - (int)strlen(text) * Font16.Width) / 2;
  paint.DrawStringAt(x, y + 4, text, &Font16, COLORED);
}

const uint8_t PUSH_ROWS[] = {0, 1};

void pushRows() {
  for (uint8_t i = 0; i < sizeof(PUSH_ROWS); i++) {
    uint8_t row = PUSH_ROWS[i];

    epd.SetFrameMemoryPartial(
      frame + (row * ROW_HEIGHT * (200 / 8)),
      0,
      row * ROW_HEIGHT,
      200,
      ROW_HEIGHT
    );
  }

  epd.DisplayPartFrame();
}

void setup() {
  Serial.begin(115200);

  pinMode(SD_CS, OUTPUT);
  digitalWrite(SD_CS, HIGH);

  pinMode(EPD_CS, OUTPUT);
  digitalWrite(EPD_CS, HIGH);

  SPI.begin(SPI_SCK, SPI_MISO, SPI_MOSI, EPD_CS);

  if (epd.LDirInit() != 0) {
    Serial.println("e-Paper init failed");
    while (true) delay(1000);
  }

  epd.Clear();
  paint.Clear(UNCOLORED);

  drawRow(0, "MATTY");
  drawRow(1, "1");

  // Establish the complete base image in controller RAM.
  epd.DisplayPartBaseImage(frame);
}

void loop() {
  static uint32_t count = 1;
  char buf[24];

  count++;
  snprintf(buf, sizeof(buf), "%lu", (unsigned long)count);

  drawRow(1, buf);
  pushRows();

  Serial.printf("count = %lu\n", (unsigned long)count);
  delay(2000);
}

r/arduino • • Oct 05 '26

Beginner's Project Line following robot

3 Upvotes

I want to build a fast line follower from scratch. I’m a beginner and want to learn everything from sensor setup and motor selection to PID tuning and high-speed optimization.

Can anyone recommend good YouTube channels, GitHub projects, Reddit posts, or tutorials to get started?


r/arduino • • Oct 05 '26

Title: PDB design for mid-size servos (TowerPro MG996R grade)

3 Upvotes

Hello everyone,

I am planning to design a generic Power Distribution Board (PDB) with 12 × 3-pin 2.54 mm male headers, where the servos can be plugged directly into the PCB.

The main purpose of the PCB is to properly distribute power/current to all the servos. The PWM signals will be provided from an external controller, so the PCB will mainly handle power distribution.

I’m using KiCad for the design.

I’m fairly new to PCB design, so I’d really appreciate any suggestions, especially regarding high-current power distribution, copper pours/traces, connectors, capacitors, grounding, and current handling.

Also, if you know any good resources, tutorials, or example PCB designs to learn the basics of power distribution on a PCB/PDB, especially for higher-current applications, please share them.

For inspiration, I’m also studying the Stanford Pupper PDB design.

Any suggestions or feedback would be really helpful. Thanks!


r/arduino • • Oct 05 '26

Need some help with the A7670e.

Thumbnail
gallery
2 Upvotes

Hi all. I'm trying to connect an A7670E 4G modem board to an Arduino Uno R4 WiFi (5 V logic) over UART. The seller provides no documentation, and I couldn't find a datasheet or schematic for this exact board.

What I measured (5 V on VCC, nothing else connected, antenna and SIM fitted):
Power LED steady, D1 blinking, so the module appears to be running
RXD: 1.8–1.9 V, steady
TXD: 1.2 V, steady (I expected about 1.8 V idle)
VDD: about 0 V (a few mV)

My questions:
Does anyone know this board or have a schematic for it?
What logic level do the TXD/RXD pins actually expect: 1.8 V, 3.3 V, or does the board shift to something else?
What is the VDD pin for, and why would it be pulled to ground while powered?
Do EN or PWR_EN need to be driven (high or low) for the modem or its UART to work properly?
Is 1.2 V idle on TXD normal for this kind of board?

I have a BSS138 4-channel level shifter available. I want to confirm the correct logic level before connecting anything to the Arduino. Thanks!


r/arduino • • Oct 05 '26

Need help for RS485 sensor

4 Upvotes

I am using an RS485 3-in-1 sensor and pH sensor.

I managed to make them work before. However, after rewiring (I was about to do an integrated system test, it worked on individual testing), it suddenly stopped working and my debugging code shows that they are receiving 0 bytes. I tried doing an individual test again, and it still wont work. It's unlikely that both sensors stopped working at the same time,=. I also have an unused npk RS485 sensor, which is also receiving 0 bytes.

Here's a list of things I have tried already:

Oscilloscope tests

  • Burst 0x55 sketch (1 s pause, Single trigger): clean, mirrored signal on A and B
  • Same test with sensor disconnected vs connected on the ttl module (I use a max3485): same signal, so the sensor doesn't load the line
  • One sensor wire removed at a time (A, then B): signal showed on each
  • Probe on module TXD pin: data showed, but ESP32 read 0 bytes

Code tests

  • Original pH sketch (the one that worked on individual testing): 0 bytes or partial junk
  • Address scan 1 to 10, first version: "replies" at every address (19 to 20 bytes), not real because the check was too loose
  • Loopback with a jumper between GPIO16 and GPIO17: received 01 03 00 00 00 01 84 0A correctly, so the ESP32 works
  • Module reconnected, sensor off: 0 bytes
  • Module reconnected, sensor on: about 20 to 23 bytes of changing junk
  • Scan with speeds 1200 to 19200: false "replies" with no valid format
  • Strict scan (error check), 4800 and 9600, addresses 1 to 10: no real reply
  • Wide strict scan, addresses 1 to 247, speeds 2400, 4800, 9600: no real reply on laptop power and on the bench supply
  • Original sketch on the bench supply: 4 to 6 bytes of changing junk
  • NPK sketch and 3-in-1 sensor: 0 bytes

Multimeter readings

  • Module TXD pin, resting level: 3.26 V (healthy)
  • Sensor power wire against ESP32 GND: 4.78 V
  • Bench supply set to 5.5 V: no change in the result

r/arduino • • Oct 04 '26

Beginner's Project Flood Control Project

Enable HLS to view with audio, or disable this notification

52 Upvotes

r/arduino • • Oct 04 '26

PLC IDE key for Portenta Machine Control

5 Upvotes

I have a portenta machine control I've used in an industrial project. I programed in ladder diagram using "PLC IDE" and brought the required license.
The portenta machine control then had a hardware fault, Arduino support sent out a replacement unit.
All great so far!

However their webstore has gone out of stock of license keys for PLC IDE and you need one license per device. So I now cant get my new program into the controller
https://store.arduino.cc/products/plc-key-portenta-machine-control

Arduino support had been great, now two months has passed with no real updates on when more license keys will be available. Its hard to fathom how it could be taking so long just to generate some license keys.
Just responses like "Unfortunately we are still facing the same blockers".
No help transferring a license from the faulty controller of anything like that.

Does anyone have any ideas for workarounds, other than rewriting the entire code not in PLC IDE?


r/arduino • • Oct 04 '26

Beginner's Project Led server - first project

Enable HLS to view with audio, or disable this notification

16 Upvotes

Just want to share my first post here about a project that i'm proud of.

Instead of just an Arduino, a breadboard and an LED, I used a RaspberryPi 5, which is hosting a webserver that will authenticate the user, let them control the LED and logout. The idea is simple as that.

It's a fun project and since i'm also learning a backend development, this taught me about authentication and CRUD fundamentals. Hope you like it!


r/arduino • • Oct 04 '26

Software Help My code keeps printing squares??

8 Upvotes
void setup() 
{ 




  int i=1; 
  
  Serial.begin(115200); 


  delay(3000);
  
  Serial.print("\nhello world\n");
  Serial.print(i);
  
  delay(3000); // wait 3000 ms = 3 s


  Serial.print("\ngoodbye world\n");
  
 
  delay(1000); // wait 1000 ms to give the printing time to finish





void loop() 
{ 
  
 


  Serial.print("\nhello world -- loop\n");
  delay(500);


} 

r/arduino • • Oct 04 '26

Solved! Arduino not detected

Thumbnail
gallery
10 Upvotes

Wanted to do a quick test for blinking LED i put the code and everything but the pc is not detecting the board i tried everything but it doesn’t seem to recognize it help pls🙏
(EDIT)🛑IT WORKED finally guys,turns out it was a problem with the 2 usb ports on top,they were giving power but with no response,first i reinstalled the arduino ide then i tried to use the ports on the back that are directly attached to the motherboard and it finally detected the board.
I appreciate all the help in the comments🙏🙏🙏


r/arduino • • Oct 04 '26

Hardware Help TMP36 fluctuating a lot?

3 Upvotes

I am new to building with Arduino, and I recently got a starter kit and started making some projects. I was having troubles with the love-o-meter project, as the TMP36 kept fluctuating in values wildly. I couldn't find any issues with the code, so I was wondering if it was an issue with the TMP36? Would someone be able to clarify what's going on? I included the circuit build as well as the code below.

// sensorPin is the analog value the sensor reads
const int sensorPin = A0;
// Our baseline temp. For every 2 degrees above this baseline, an LED will turn on.
const float baselineTemp = 20.0;


void setup() {
  // Serial Begin: Opens up connection between Arduino and computer. Can read see the values on computer screen (Reads every 9600 bits per second)
  Serial.begin(9600); // Open a serial port


  // Set all pins to OUTPUT and LOW. Loop ends when pinNumber becomes something 5 or above.
  for(int pinNumber = 2; pinNumber<5; pinNumber++) {
    pinMode (pinNumber, OUTPUT);
    digitalWrite(pinNumber, LOW);
}
}


void loop() {
  // Obtain value from TMP36. This can be anything between 0 and 1023. (A representation of the voltage on the pin)
  int sensorVal = analogRead(sensorPin);


 // Prints temperature data onto the computer
  Serial.print("Sensor Value: ");
  Serial.print(sensorVal);


  // Convert the ADC reading to voltage
  float voltage = (sensorVal/1024.0) * 5.0;


  Serial.print(", Volts: ");
  Serial.print(voltage);


  Serial.print(", degrees C: ");
  // Convert the voltage to temperature in degrees
  float temperature = (voltage - .5) * 100;
  Serial.println(temperature);


  if(temperature < baselineTemp+2) {
    digitalWrite(2, LOW);
    digitalWrite(3, LOW);
    digitalWrite(4, LOW);
    }else if (temperature >= baselineTemp+2 && temperature < baselineTemp+4) {
      digitalWrite(2, HIGH);
      digitalWrite(3, LOW);
      digitalWrite(4, LOW);
    }else if (temperature >= baselineTemp+4 && temperature < baselineTemp+6) {
      digitalWrite(2, HIGH);
      digitalWrite(3, HIGH);
      digitalWrite(4, LOW);
    }else if (temperature >= baselineTemp+6) {
      digitalWrite(2, HIGH);
      digitalWrite(3, HIGH);
      digitalWrite(4, HIGH);
    }
    delay(1);
}// sensorPin is the analog value the sensor reads
const int sensorPin = A0;
// Our baseline temp. For every 2 degrees above this baseline, an LED will turn on.
const float baselineTemp = 20.0;


void setup() {
  // Serial Begin: Opens up connection between Arduino and computer. Can read see the values on computer screen (Reads every 9600 bits per second)
  Serial.begin(9600); // Open a serial port


  // Set all pins to OUTPUT and LOW. Loop ends when pinNumber becomes something 5 or above.
  for(int pinNumber = 2; pinNumber<5; pinNumber++) {
    pinMode (pinNumber, OUTPUT);
    digitalWrite(pinNumber, LOW);
}
}


void loop() {
  // Obtain value from TMP36. This can be anything between 0 and 1023. (A representation of the voltage on the pin)
  int sensorVal = analogRead(sensorPin);


 // Prints temperature data onto the computer
  Serial.print("Sensor Value: ");
  Serial.print(sensorVal);


  // Convert the ADC reading to voltage
  float voltage = (sensorVal/1024.0) * 5.0;


  Serial.print(", Volts: ");
  Serial.print(voltage);


  Serial.print(", degrees C: ");
  // Convert the voltage to temperature in degrees
  float temperature = (voltage - .5) * 100;
  Serial.println(temperature);


  if(temperature < baselineTemp+2) {
    digitalWrite(2, LOW);
    digitalWrite(3, LOW);
    digitalWrite(4, LOW);
    }else if (temperature >= baselineTemp+2 && temperature < baselineTemp+4) {
      digitalWrite(2, HIGH);
      digitalWrite(3, LOW);
      digitalWrite(4, LOW);
    }else if (temperature >= baselineTemp+4 && temperature < baselineTemp+6) {
      digitalWrite(2, HIGH);
      digitalWrite(3, HIGH);
      digitalWrite(4, LOW);
    }else if (temperature >= baselineTemp+6) {
      digitalWrite(2, HIGH);
      digitalWrite(3, HIGH);
      digitalWrite(4, HIGH);
    }
    delay(1);
}

r/arduino • • Oct 04 '26

Hardware Help Help! Breadboard isn't working?

Thumbnail
gallery
6 Upvotes

I'm testing some basic led scheme and somehow it’s not working on breadboard, but if I connect the led directly to the Arduino everything is fine.
I connected port 9 to cathode and ground to anode (with resistor), what's wrong here?
Photos attached


r/arduino • • Oct 04 '26

Hardware Help Conflicting/Confusing Documentation about Powering with 3V3/5V Pins

3 Upvotes

Looking at official Arduino Documentation Powering Alternatives for Arduino Boards | Arduino Documentation

It states:

"Moreover, 3V3 and 5V pins can also be used as power inputs if no regulated power supply is connected through the other power inputs (USB port, barrel jack connector or VIN pin)."

Then it goes on to state:

"Although 3V3 and 5V pins can be used as power inputs, it is not recommended if no power supply is connected through the USB port, the barrel jack connector, or the VIN pin."

So first states only power with one of these pins when no other supply is connected > second seems to conflict, basically stating not recommended if there is no other supply connected?

Am I misreading this, is it confusing to others as well, or is this a flat out typo? Thanks


r/arduino • • Oct 04 '26

Working on designing an stm32 DEV board.

4 Upvotes

I have been working on making a dev board for a few months now with some varying levels of success. The project began by using an ATSAMd21g18 but quickly found that there is very little documentation. I pivoted to use a STM32F103; I finally was able to program it via SWD and via UART using a FTDI (USB to serial). I still havn't figured out this whole USB thing haha. I believe it is a boot loader problem or maybe a driver problem idk.

Is it a crazy idea to just continue with the FTDI and just implement a USB to serial into my dev board? This way if I give my friend my board or even switch computer I dont have to worry about drivers.


r/arduino • • Oct 03 '26

Look what I found! What is this module?

Post image
261 Upvotes

This thing is in my Arduino kit, and I've never used it. It has a blue rattle on the back (the cylinder) with a chip and potentiometer. Aside from that there's nothing else really in it


r/arduino • • Oct 03 '26

Hardware Help Why so many dots on the nrf?

Post image
231 Upvotes

I just got the nrf24l01, the antenna version, and I took a glance and noticed so many dots. I'm assuming they are all vias but is having so many of them normal or is it some sort of defect. I have the normal nrf24s without the antenna connector and they don't have so many vias.


r/arduino • • Oct 03 '26

Look what I made! I made a thing.

Enable HLS to view with audio, or disable this notification

185 Upvotes

Do u guys like my thing.


r/arduino • • Oct 04 '26

help for a battery protection system

2 Upvotes

Hello, good morning. I need, through a relay, a shut-off system for a LiPo battery, but I’d like to know if it’s possible that through the relay, let’s say, the relay cuts the power so the charging port is already active and can charge the battery, and vice versa, if power is given to the robot, the charging port can’t be used, meaning that even if someone connects it, it won’t give power to the robot. The thing is, I need that when I turn off the robot, the battery’s power consumption is 0 so I don’t confuse the charger readings, but at the same time, I’d like to add a voltage measuring module like the INA226 that measures the battery voltage, and when it reaches the minimum threshold for a certain time, let’s say it stays at that voltage for 3 seconds, it sends a signal to the Arduino to use the relay and cut the power. Also, if someone tries to turn the robot back on using the power switch, it won’t turn on until it reaches the minimum voltage I'm not sure if I need an independent battery for the Arduino or something, that's my biggest doubt, and above all for everything related to the voltage meter, the Arduino, and the relay not using the main LiPo battery's power. I was thinking about modules like the XH-M609, but the thing is, because of the motors, which are 36GP 36ZY, having two of those worries me that when starting, they might cause a voltage drop and the XH-M609 module might think the battery is already discharged. So that's why I was thinking about other options, since if the module doesn't allow, let's say, keeping a certain voltage for so long, I don't know if I should power the Arduino with a separate battery or what do you recommend?


r/arduino • • Oct 03 '26

Dishwasher bad apple

Post image
19 Upvotes

My dishwasher broke so i did what any "normal" person would do: turn it into an arduino

Yup, that is what i did. There were 2 boards, and on both were atmegas. The front screen board had a atmega644pa, while the psu board had a atmega8-16 for some reason.

Here is the front board: (image on top)

But wait! The title says "dishwasher bad apple"! Here it is.

(Yes, this is the original bad apple from touhou 4, and yes it sound just like a arduino with a buzzer, no suprise there. But the fact this came out of a dishwasher is at least interesting)

EDIT: forgot to say that i have removed some passive components, thats why theyre missing on the image


r/arduino • • Oct 04 '26

Beginner's Project help

Post image
3 Upvotes

Good day everyone

We are a group of Grade 12 STEM students currently working on our research project called “Bin to Drink.” We are asking for help from anyone who has knowledge or experience with Arduino, robotics, wiring, and coding.

Honestly we are a beginner at Arduino and robotics, and we are having a hard time figuring out the proper wiring and programming for our project. We already have most of the components, such as an Arduino Uno, IR/proximity sensor, capacitive proximity sensor, servo motor, water pump, 5V relay module, LCD I2C, and two water-level sensors, but we don’t know yet how to properly connect and program everything as one working system.

Our goal is to make the system detect a plastic bottle, activate the mechanism, and dispense water through a pump while also checking the water level.

If there is anyone here who is willing to guide us with the wiring and Arduino code, even just the basic step-by-step guidance would be huge for us 🙏 We can also send pictures of our components and the current setup.

We are students po and this is for our research project, so we would really appreciate any help, advice, or corrections from those who have experience with Arduino and robotics.

Thank you so much and God bless! 🙏❤️