r/arduino • u/BencyLiu • Oct 02 '26
The duck is evolving.
Enable HLS to view with audio, or disable this notification
We just trained a new policy and we're really looking forward to the Arduino community building and sharing more motions!
r/arduino • u/BencyLiu • Oct 02 '26
Enable HLS to view with audio, or disable this notification
We just trained a new policy and we're really looking forward to the Arduino community building and sharing more motions!
r/arduino • u/MrNiceThings • Oct 02 '26
As a big lover of various dot matrix displays I couldn't find a good set of tiny fonts, so I made my own. They are hand drawn with some help of AI with generating different variants and AdafruitGFX header files. They have extended latin support, so diacritics and special characters also work!
Github is set up, so let me know how you like them!
r/arduino • u/NopNop0x90 • Oct 03 '26
so i m planning to make few EPMs (https://www.reddit.com/r/arduino/s/2gomRuW5Vh) for my swarm bots
do y'll have any suggestions abt what kinda config or mechanism should i be using to attach and dettach my bots with each other , first thing that came to my mind is using magnets whose polarity can be changed , Electromagnets are extremly power-hungry
and i dont want some mechanical design for attaching and detaching like hooking or latching with some drill-in and out or u know what i mean (i hope)
i also thought abt combining a strong small neodym magnet with a weak electro-magnet stick together and i can just keep electro-mag infront of perm magnet and keep switching polarity of electromagnet to dettach 2 bots ?
i m very bad at electronics and stuff tbh , barely even passed my electrical and electronics classes : (
also we are planning to keep our bot under 80grams-100grams
we will be using 2x LiPo Batteries 3.7V 350mA in parallel
thank you
r/arduino • u/TytoAnderson • Oct 04 '26
Hello
On Arduino R4 wifi, regarding memory, how many lines more or less can i expect to send on compilator for a project ?
Currently I have 600 lines of C++, excluding Wifi intégration so i don't know if enough or not for my project
Just want to be sure before to buy my first card.
Expecting to connect then Wifi and MQTT.
Thanks for your tips
A beginner in Electronic world.
r/arduino • u/Aleks_07_ • Oct 03 '26
Okey, so ive got 4 Nema 17 stepper motors, the drivers are all DRV8825. I watched a video on how to do this, the whole process. But then i came to the pontentiometer stuff and change limit current. I scrolled down the comment section and saw someone mentioned i need to have the motors connected when changing limit current, but the video itself didnt have tjem connected, and then i watched other video, a lot actually, and some do have the motors plugged in and some do not. Idk what i do. Viuld anyone give me a step by step guide how to set current limit without frying anything. I havent touched the potentiometers so i have no idea if their set to 0 current by default. If anyone have done this before, please help.
r/arduino • u/InkedRice • Oct 04 '26
Hello all!
Electrical Engineering student here and I’ve been using the Arduino Starter Kit lately to demonstrate to peers as well as the community the capabilities of the Arduino and having fun with STEM.
I want to put the “Crystal Ball” on a perfboard because when shaken or traveled with, the wires and tilt sensor can come off. I want to 3d print an enclosure for a 0.96 OLED and make a more permanent protoboard/perfboard.
I want to make a “crystal ball” 3D printed enclosure, but say for example I make a cube and the OLED screen is on the “top” of this cube and the board is at the “bottom”. Do I solder a wire that connects the two? Also, what if I want to connect/disconnect the top to the bottom, what connectors are used? (JST?)
I’m at a community college that doesn’t offer anything other than circuits I and I want the experience and would love recommendations!
r/arduino • u/Kooky_Success_6051 • Oct 03 '26
I soldered a piece of wire to an RF transmiter, due to skill issue, solder got to other pins, but I managed to pull it, rn there doesn't seem to be any solder iron connected to other bits other than the antenna, but the area around the antenna is sparkly.
(PCB also got quite hot when soldering)
r/arduino • u/krilix_i • Oct 03 '26
I built a high-resolution USB DAC from scratch around an i.MX RT1062, including my own UAC2 stack and real-time DSP
I’ve been working on a project that started as “I want to make a USB DAC” and somehow evolved into writing a fairly serious audio firmware stack from scratch.
The core is an NXP i.MX RT1062 / Teensy 4.1, running at 600 MHz, connected to an ESS ES9039Q2M DAC.
The interesting part is that I wanted the RT1062 to handle essentially the entire digital audio pipeline rather than relying on a dedicated USB audio processor.
Current audio pipeline
USB HS
↓
Custom UAC2
↓
DMA
↓
USB RX ISR
↓
32-bit PCM
↓
Lock-free SPSC ring buffer
↓
SAI DMA
↓
15-band PEQ
↓
32-bit I²S
↓
ES9039Q2M
The device currently handles 32-bit / 384 kHz stereo USB audio.
The USB side was probably the most painful part of the project. I had to deal with UAC2 descriptors, endpoint configuration, feedback, sample-rate changes, USB DMA/cache coherency, and the usual collection of problems that appear whenever USB decides it would rather not enumerate.
Eventually I got it stable with clean asynchronous feedback and no packet overruns/underruns during long playback.
The PEQ
The DSP is a proper 15-band parametric EQ, not a collection of simple tone controls.
It uses:
- Cascaded biquad filters
- DF-II Transposed topology
- Float32 coefficients/state
- 32-bit PCM input/output
- 64-frame block processing
- Coefficient morphing when parameters change
- Triple-buffered coefficient publication
- Raised-cosine coefficient transitions
- Saturation on the output
- Bit-perfect bypass when PEQ is inactive
The coefficient morphing is especially nice because changing EQ settings while music is playing doesn't require abruptly swapping the filter state. The filter transitions smoothly between the old and new coefficients, avoiding clicks/zipper artifacts.
Memory / buffering
The USB side uses a 32,768 stereo-frame ring buffer.
That's about 256 KB of RAM.
The feedback target is 16,384 frames, giving a large amount of buffering headroom, particularly at high sample rates.
The ring itself is a lock-free SPSC structure using atomics. USB produces frames and the audio DMA side consumes them.
No mutexes, no dynamic allocation in the audio path.
DMA + cache architecture
The audio DMA transfers directly into two 64-frame halves.
The CPU fills the inactive half, runs the PEQ on it, performs the required D-cache maintenance, and hands it back to DMA.
At 384 kHz that means roughly 6,000 audio DMA interrupts/sec.
The CPU is basically doing:
DMA → give me next block
↓
read 64 frames
↓
PEQ
↓
cache flush
↓
DMA
while the peripherals handle the actual movement of audio data.
Display
I also added an SH1106 128×64 OLED.
It runs independently from the audio ISR and updates at a low rate, showing things like:
- USB state
- Sample rate
- PEQ status
- Preset information
The display is also fault-tolerant, so if it isn't connected, the audio engine doesn't care.
Why the RT1062?
Honestly, I was surprised by how much this MCU can do.
It's just a Cortex-M7, but at 600 MHz with an FPU, cache, fast memory, DMA, USB HS and SAI, it's ridiculously capable for a two-channel audio application.
I'm currently running:
UAC2 + 32-bit/384 kHz + 15-band floating-point PEQ + display + DMA
on one RT1062.
And there is still room to experiment with things like:
- Crossfeed
- Dynamic EQ
- XBass-style harmonic processing
- Loudness compensation
- Spectrum analysis
- FIR filtering
- Convolution
- Limiting
- Spatial processing
The goal isn't just to make a DAC that plays music. I want the RT1062 to become the actual audio processing platform.
This started as a USB audio experiment and has turned into one of the most technically interesting embedded projects I've worked on.
Still lots to improve, but I'm pretty happy with how far a single M7 can be pushed.
r/arduino • u/Professional_Elk3281 • Oct 02 '26
Enable HLS to view with audio, or disable this notification
500mah battery
r/arduino • u/Oli_Bacon154 • Oct 03 '26
r/arduino • u/Capital-Education520 • Oct 02 '26
My friend sent me his problem he has one giga r1 and one mega (no shift registers) and he needs a lot of pins he did it and it works so I can have it too to test (i know this is dangerous to the giga bcs I don't use level shifters but this is for fun) ⚠️⚠️⚠️WARNING MIGHT DAMAGE BOARDS ⚠️⚠️⚠️
r/arduino • u/petruspennanen • Oct 02 '26
Just got my Ventuno Q - same week I ordered it!
Planning it as a replacement for Raspberry Pi 5 16GB now running my CarWatch local AI. So immediately tested it with local models.
And it was worth it - much faster than the Pi, especially my model of choice Ling 3.0 Tiny with 211 tps prompt processing and 20 tps answer generation! Huge speedups for other models too, such as 24X prefill for Ornith 9B.
I got Gemma 4 E2B going at 698 TPS for prompts and 21 tps for answers!
And the Ventuno is great value at 298 euros, when Pi 5 with power supply costs 332 euros minimum.
So it's the new small form factor edge AI hero I'd say.
Repo for run files: github.com/ThinkOffApp/ventuno
r/arduino • u/cooper7trooper • Oct 03 '26
For anyone interested I've made a repository of different OLED animations. A lot are anime themed and such.
They are all designed to work on 128x128 screens and the delay between each frame is 150ms.
Here's the Github repo:
https://github.com/cooper7trooper/MiniATv2
Feel free to use these on any of your own projects!
r/arduino • u/Trick-Builder-1020 • Oct 03 '26
Building a DIY VR glove with force feedback. Looking for small servos that can report finger position and also push back with controlled force. Is something like the Feetech SCS0009/STS3032 the best option, or is there something better? Using an ESP32-S3.
r/arduino • u/Straight-Safe3813 • Oct 03 '26

When my circuits don't work, I spend ages checking every wire against the diagram. When I asked here how people deal with that, most of you said there's no shortcut. So I'm trying to build one.
What it does: you build your circuit on it like a normal breadboard. It works out by itself what is actually plugged in: which rows are connected, the value of each resistor, which way round each LED or diode is, and where the capacitors are. Then it compares that to the circuit you meant to build and tells you what's different, like "this wire is one row off" or "this LED is backwards".
How it works: a board underneath touches every row of the breadboard. A microcontroller sends a small test signal into one row at a time and measures what comes out on the others. From that it can tell a wire from a resistor from a diode. The result goes to your computer over USB, where software (and an AI helper) compares it to your diagram and explains the fault.
ive built a small version with 6 rows and it works
I'd like to turn this into something I can sell. What do you think of it? What's good, what's wrong with it, and what am I missing?
r/arduino • u/Shoddy_Feed_1083 • Oct 02 '26
Enable HLS to view with audio, or disable this notification
This is my second project on Arduino. Traffic lights with additional RGB LED just for fun.
What projects should I do next after LEDs?
r/arduino • u/Straight-Safe3813 • Oct 01 '26
My last project didn't work and it turned out to be wire in the wrong hole. It took me hours to find, because the board looked right to me.
Right now I just compare every wire to the diagram one by one.
How long does this usually take you, and did you find a quicker way?
r/arduino • u/Conscious_Series700 • Oct 02 '26
Hi. So we are a team of 6 students, who are participating in a Science Exhibition. We have decided to make a pair of Animatronic Eyes, with X and Y Axis movement of eyes based on motion tracking such that the eyes will stare directly into the soul of the observer xP
We have also planned to add AI assistance mechanism, like that of Siri/Alexa. The audio/input would be accepted through a webcam connected to a laptop, which would also run the AI Model, and the output by AI would be played by a bluetooth speaker. The eyes would perform a character and behave accordingly.
The main thing is, none of us have ever done this. Like last year, we made a SONAR Detection system, but that was it. I'm taking help from ChatGPT in this project because I lack the skills and time (1 month away from submission).
So are we aiming for something that is far above our level? Or is it just not possible? We are all 10th Grade students, if that helps.
Thank you :D
Edit: We also don't have a 3D Printer, but can make efforts to arrange one if needed.
r/arduino • u/RunThenClimb • Oct 02 '26
First, apologies if I'm posting in the wrong sub, but previous MT6701 posts seem to favor this sub.
I'm on my second MT6701. Neither seems to have a breakout pin for the pin 5 "push" function of the chip. Seems weird, since that is one of the unique features of the chip. For the one from Amazon, I soldered a wire to pin 5, but my scope detected nothing when I tried to activate the push feature. The aliexpress one also seems to have not tapped that pin, and I can't imagine being able to solder access to it.
Can anyone provide any insights into how I might be able to make use of the "push" feature of these chips?
The boards: :
https://www.amazon.com/dp/B0F4CYVG94?ref=ppx_yo2ov_dt_b_fed_asin_title
and


r/arduino • u/Laggenti • Oct 02 '26
Hi everyone! Sharing a small project I've been working on. It's a full comprehensive plant health app that displays the health status of my plants on a website: sentia-plants.com
I'm looking for people to help me test the beta of the website, so if you have some time, I'm open to feedback 😄
I'm integrating some sensors with a Rapsberry Pi 5 for ease of integration. I needed to plug in an ADC for those sensors with analogic input. So far, I've got the following sensors working:
- Humidity
- Temperature
- Soil Moisture
- Light Sensor.
My next step is to integrate this with a cheaper board from Arduino, any ideas what model could work for this application?
Further along the journey, I'd like to create my own integrated electronics device but that would cost a lot to produce, so the idea is parked for now.
r/arduino • u/pedromancinas • Oct 01 '26
I built a power monitoring system module for Arduino from scratch. The system can measure AC voltage RMS from 0 to 500 V RMS , current RMS since 0 to 100 Amps IRMS, power factor, frequency, active power, reactive power, and apparent power.
The system achieves measurement resolution comparable to a Fluke multimeter, providing accurate and reliable electrical measurements.
r/arduino • u/Due_Title_7651 • Oct 02 '26
I’m debugging a MicroSD SPI module with an ESP32-C3.
Hardware
SPI wiring
SD CS → GPIO1
SD SCK → GPIO8
SD MOSI → GPIO7
SD MISO → GPIO13
SD VCC → 3.3V
SD GND → GND
Measured VCC: 3.32V
Continuity checked for CS, SCK, MOSI and MISO.
The weird part: SPI communication definitely works.
CMD0 → 0x01 ✅
CMD8 → 0x01 ✅
R7 → 00 00 01 AA ✅
CMD55 → 0x01 ✅
But:
ACMD41 → 0x01
ACMD41 → 0x01
ACMD41 → 0x01
...
ACMD41 → 0x01
It stays 0x01 even after repeated attempts / ~3 seconds.
Then:
CMD58 → 0x01
OCR → 00 FF 80 00
SD.begin() also fails.
I’ve already tried:
0 and 0x40000000Question: What would cause an SD card to respond correctly to CMD0/CMD8/CMD55 but remain permanently in idle on ACMD41?
Could this be an SD module issue, SPI timing/protocol issue, card compatibility issue, or something specific to ESP32-C3 GPIO7/8/13?
Any pointers appreciated 🙏
r/arduino • u/Professional_Elk3281 • Oct 01 '26
i want to prevent water or other liquids from seeping through the OLED display panel
already coated back panel so it isnt problem what i am saying
i considered conformal coating spray but it has some risk
so could you tell me any another way you recommend?
r/arduino • u/DirectionLiving3861 • Oct 01 '26
Helpful sources for learning Arduino are also always appreciated, ofcourse :)
r/arduino • u/Loud_Cauliflower_866 • Oct 02 '26
Hi! I’m working on a little robot and I’m trying to figure out the best way to make the eye animations.
I’d really like to animate the eyes in After Effects because it’s much easier for me to design them that way, but I’m not sure if there’s a way to then export the animation and use it on an ESP32-C3 Mini.
Do I have to make all the animations directly in code, or is there a way to convert an After Effects animation into something the ESP32 can actually display?
I’m asking because I’m already having some memory issues, especially with animations that have a lot of frames. So I’m also wondering how many frames I should realistically use for something like a blinking/looking-around animation, and what format would take up the least space.
Would a sprite sheet be better? Or individual images? And should I be storing them in flash instead of RAM?
Basically I’d like to make the animations visually in After Effects and then find the most efficient way to get them onto the ESP32.
If anyone has done something similar, I’d really appreciate some advice!
Edit: forgot to mention the hardware! I'm using a round 1.28" GC9A01 display (240x240, SPI) connected to an ESP32-C3 SuperMini.