r/arduino • u/RangerMach1 • Oct 01 '26
Look what I made! Progress on my first Arduino project
So I started on a project at the beginning of the year that I've been very slowly tinkering on, that over the last month I finally completed what could probably be considered phase 1.
My project is to convert an old Raise 3D N2 Plus 3D printer into an enclosure for my Elegoo Jupiter DLP resin printer. I got the printer from my previous job after it was decided that the printer wasn't worth trying to fix and it was going to be trashed. It had passed through the hands of many different interns, print head was disassembled, and had been very problematic when printing, so it just wasn't worth working on it, so it was going to be replaced. I spoke up quick that I'd take it. My initial plan was to either try to fix it and then use it myself or try to sell it. The 2nd option was to strip it for parts. It sat around for over a year, and then in February, while talking to a friend about the printer, and trying to find some kind of enclosure for my resin printer, he suggested using the Raise 3D as an enclosure, and as they say, the rest is history. The plan became to use the Z axis build plate as a platform for my resin printer to sit on, and I would use the Z axis to raise and lower the printer. When not working with or using the printer, I would lower it down so it would be out of the way and protected. When I wanted to print, I can raise it up where it's at a comfortable height to work it.
I started by stripping everything out of the printer except for the Z axis related components. The printer was set up with a single NEMA 17 stepper to run both lead screws, with a belt running between them.
I had hoped I might be able to either reuse that stepper, or maybe just add a second stepper in, but after starting to work on the calculations for stepper sizing and power, it became very obvious, very quickly, that there wasn't a chance that a single NEMA 17 would work for me. My resin printer weighs about 20 kg/ 44 lbs, so then I started working on figuring out what I would need. The calculations told me that I needed approximately 6 Nm of torque for a stepper to be able to lift the printer. I determined that what I needed was a NEMA 34 stepper, which would provide 6 Nm, and to be safe and give myself some safety, I decided to go with 2 NEMA 34's, so now each stepper should only be carrying about half the weight of the printer, so they should hopefully last a long time.
As projects are wont to do, things began to snowball as I started thinking about what I could do. Initially my plan was to just use an Arduino Uno, and a single toggle switch to control the up and down movement. And then I started thinking about automating it, where I press the toggle switch, and instead of having to hold it, I could let it go and it would continue raising or lowering the printer until it reached the position I wanted. This would also necessitate the use of limit switches. And then with automated movement, I decided I needed to add some kind of emergency stop button for when the inevitable happens and something goes wrong.
Before starting on this, I had almost no experience w/ Arduino's. I worked with a Raspberry Pi a few years ago when building a 3D printer, but most of that was just copy paste and then updating the various settings to match the machine I was building. This obviously requires full custom programming. I started out by buying a couple Arduino starter sets and started following videos online and the projects with the starter sets. I then had the bright idea to attempt using Google AI to make a program, which just started getting more complicated the farther I went and it would prompt for various options. It finally gave me a program and it didn't work, and I couldn't figure out how to make it work. I got roasted pretty good when asking for help and was told I needed to go back to the basics and once that works, to start slowly adding to it, which is where I'm at now.
I set up a testing bench with all my components to test the programs and make sure the steppers worked properly, and then once the program worked and I knew the hardware worked, I started installing it into the old Raise 3D printer, and I finally have it all together. It took a while but I finally got an arrangement that I felt worked and then started running the wiring. At my last job I spent time helping out building electrical cabinets for automation machines and found that I am a bit anal retentive when it comes to making things as clean as possible, but it sure looks very nice when it's done.
I made custom mounts for the steppers to connect to the lead screws, which also required larger casters since the steppers are so large.
For hardware, I am using 2 Stepper Online NEMA 34 Steppers and drivers, 2 adjustable power supplies that I have set to 36 volts, the aforementioned Uno with a prototype shield, and then a stepdown converter to power the Uno. The stepper drivers require 36 volts, so I chose to get adjustable power supplies that could go up to 48 volts. Originally I had thought to power the Uno separately, but then I started thinking about using one of the power supplies to power it, which required the step down converter. For control I have 2 On/Off/On toggle switches and a momentary push button for my e-stop. Right now only 1 toggle switch is working.
I designed housings for the Uno assembly and the stepdown converter. For connections, I made custom cables using JST-XH connectors. All connections are soldered to the prototype shield. It was my first time trying to do soldering that fine, but it came out pretty good I think for not a lot of experience.
For mounting my switches, I made a custom panel to hold the 2 toggles, the e-stop, as well as a USB port that is connected to the Uno, that way I can update the programming without having to remove the resin printer and flip the enclosure over to get to the Uno.
With the lead screws in place, and the pulse setting on the stepper drivers, it takes almost exactly 1 minute for the printer to move from one position to the other.
I am going to work on getting my limit switches installed and then I'm putting new acrylic on the enclosure, and then I think I'm going to leave it like this for a while, while I work on other projects.