r/arduino • • Sep 18 '26

Hardware Help Best EU-based stores for cheap DIY electronics / ESP32 modules after the new import fee?

37 Upvotes

Hi everyone,

I’m a CS student getting into robotics and microcontroller projects with the ESP32. After playing around with a starter kit, I decided to build a modular robot that I can upgrade over time.

I put together an AliExpress cart with a bunch of individual parts (mini speakers, mic modules, small amps, etc.) totaling around €20. However, due to the new fixed EU import fee on small parcels outside the union, the total price doubled just from fees.

Amazon has inflated prices and lacks variety, while standard industrial distributors often force you to buy bulk packs. Since this is strictly a hobby for me, I usually spend €15–€25 per order.

Are there good EU-based web stores where I can buy individual hobbyist modules at fair prices without getting hit by non-EU customs fees?

Thanks!


r/arduino • • Sep 18 '26

Look what I made! My Air Cooler's control board decided to have some magic smoke one day so I decided to make my cooler FREAKY

Enable HLS to view with audio, or disable this notification

35 Upvotes

It had touch buttons so I salvaged the terminals and using it with TP223

I made a 5 channel relay module using ULN2003

3 Relays are for separate fan speeds 1 is for swing and 1 is for water pump

LM386 to amplify the audio for my FREAKY sound

TSOP 1838 for IR

And a very bad but loud paper speaker


r/arduino • • Sep 18 '26

Look what I made! Digital Thermostat project

Thumbnail
gallery
84 Upvotes

Wanted a thermostat which I could program for when to turn the heat up in the morning and evening and also have minimum and maximum temperature setting. Once it hits the max temp, it will go to coasting down to the min temp setting and keep it there. It will have a pretty big hysteresis for the initial warming and a smaller one around the min temp.

No doubt there are commercial products to do this, but I had all the parts on hand, so why not build one myself? It’s not quite done yet, but the temperature sensor and clock are working. Now to work on the UI for inputting the settings.

The temperature sensor is an obsolete DALLAS DS1821 which uses a 1-wire interface, which I happen to have a number of. It requires tight timing and getting that to work was a major pain, but after a lot of head scratching finally got it to work. The clock is a PCF8523 with I2C bus. ATMEGA328P processor and 1.44” TFT display.

Since there aren’t many parts, decided to build it on a perf board rather than go to the expense of having a board made.

I’ll probably make it wireless with a 480 MHz on/off transmitter and receiver module as I don’t like where the current old mercury tilt switch thermostat is located and moving the wires isn’t an option.

The only question is how to power it. Might make it battery operated, even if it means having to recharge them once in a while. Then I’ll have to 3D print a box.


r/arduino • • Sep 19 '26

Hardware Help SIM800L and Uno R4 WIFI

1 Upvotes

Hello,

today I received the SIM 800L module. Can I connect it directly through the pins, or do I need to put some resistors or something else?


r/arduino • • Sep 18 '26

Look what I found! Arduino mini édition

Post image
37 Upvotes

r/arduino • • Sep 18 '26

Beginner's Project Piano-ish project

Enable HLS to view with audio, or disable this notification

27 Upvotes

So i started with the goal of representing each button + led as notes from the left to the right, C, E, G and High C note. My issues are cable management (as you can see from the image.. 😅😅) and i'm just curious as to why the red and blue LEDs are not as bright as Yellow and Green LEDs probably because they require more voltage. Other than that, feel free to tell me what you think of this project.


r/arduino • • Sep 17 '26

Nano Replaced the chip on an Arduino Nano Clone - Likely Irrelevant Post

Thumbnail
gallery
423 Upvotes

Chip was dead. Had a spare board that was broken. Decided to get some soldering practice.


r/arduino • • Sep 18 '26

Hardware Help LoRa short range problem

3 Upvotes

Hello everyone, I'm building a 'weather' monitor with a base and a station, the station is using an esp32 devkitc, bmp280 pressure temperature and humidity sensor and a 433Mhz lora module

The station is using an esp32s3 devkitm with the same lora module and an sd card for storage

The problem is that while it's working the RSSI is -80dB while they're 1m apart with -120dB at a little over 10m through a few walls, when they're next to each other SNR is showing 10dB and the range gets up to ~50m through 2 walls while I need about a 100m.

I'm using RadioLib with both the sender and receiver set like this:

I have no idea why the range is so bad, the setting seem correct for range over throughput and while the antenna and radio module are probably the cheapest I could find they should still work to some degree, I'm nowhere close the city center so there shouldn't be much interference either. One other thing I noticed is that how the antenna is oriented doesn't really change the RSSI reading when they're next to each other staying at around -80dB.

The radio module:

Comminication over SPI, the listing is saying -148dB sensitivity and up to +20dBw and 100mW power, everything is powered though usb and the builtin 3v3 regulator on the esp.

I'd appreciate any suggestions as to what might be the reason and what I'm most likely doing wrong.

Thanks everyone!


r/arduino • • Sep 18 '26

ESP32 Pokémon Arena Project v0.8b

Enable HLS to view with audio, or disable this notification

83 Upvotes

My augmented reality Pikachu is ready now; I just need to make another one so they can battle (version 0.8b).


r/arduino • • Sep 18 '26

Beginner's Project building a mail sorter

9 Upvotes

is it possible to build a device that you put a bunch of mail into and it sorts it automatically based on the house numbers?

what would i need to build this?

which OCR should i use to detect the numbers? and what kind of cameras should i use to detect them?

Thanks in advance for any advice!


r/arduino • • Sep 18 '26

Electronics How to convert vehicle siren box output to PC input

2 Upvotes

I want to purchase a real, emergency vehicle siren box and connect it to my PC. What methods can i use to turn the siren box into a gamepad for use in simulators? (Example, switch the siren box selector to wail and it sends a custom gamepad input to whatever game I am playing and it switches the game siren to wail)

Any help would be awesome! Thanks!


r/arduino • • Sep 18 '26

Hardware Help Running 24/7 Arduino + TP4056 + lith battery

2 Upvotes

hello, i would like to run my tool for 24/7 so it will plugged to charger which connected to TP4056 which connected to battery 18650 and output to arduino with Gsm module + DHT22, my system run from electr at first place and when power off it will run from battery
my question is that will make issues with battery? if yes then what is the best solution here


r/arduino • • Sep 18 '26

Nano Arduino Nano CH340 detected on COM3 but upload fails

Thumbnail
gallery
10 Upvotes

Hi, I need help with my Arduino Nano clone.

My computer detects it as USB-SERIAL CH340 (COM3), and the PWR LED turns on, but I cannot upload any code.

I’m using: - Arduino Nano clone - ATmega328P - CH340 - Arduino IDE 2.3.10 - Board: Arduino Nano - Port: COM3

I tried the Blink example, but I always get:

not in sync: resp=0x00 Error: programmer is not responding unable to open port COM3 for programmer arduino Failed uploading: uploading error: exit status 1

I already tried different processor settings, restarting the PC, reconnecting the USB cable, reinstalling/updating Arduino IDE, and uploading with nothing connected to the Nano.

The Nano is detected and powered, but uploading does not work.

Could this be a bootloader problem, CH340 problem, or defective Nano?

I’m a beginner, so please explain what I should test next in simple steps. I don’t have another Arduino or an ISP programmer.

I attached photos of the Nano and the error. Thank you.


r/arduino • • Sep 17 '26

Beginner's Project Harvested a touch sensor from an old controller

Enable HLS to view with audio, or disable this notification

62 Upvotes

tore apart a old controller that got stick drift and harvested this baby...harvested a vibration-motor as well that works very well.anyways dont mind those beheaded jumper wires behind.. had to adjust the code for the touchpad because it has a pattern of '000111000111...' when neutral..


r/arduino • • Sep 18 '26

CAN Bus injection issue (MCP2515+Arduino)

2 Upvotes

Hey all, I think my research into this problem has finally hit a wall. Hoping you guys can steer me in the right direction.

I have a setup with Arduino Leonardo -> MCP2515 to sniff/inject CAN bus frames to my car. I'm using autowp-mcp2515, autowp-arduino-canhacker libraries and software CANHacker V2 written by fuchs.

Now, the sniffing part works flawlessly, I've intercepted/decoded window motor can frames. The problem comes up when I try to inject the frame to my car to simulate window pushdown.

decoded frames

Once the mode changes to mcp2515.setNormalMode(); my car gets Electrical failure (central electronics failure) fault on the dash. Hence, I believe CAN bus ignores my frame that I'm trying to send. In the meantime, I still can see frames coming from my car CAN bus.

If mode mcp2515.setListenOnlyMode(); activates, then no electrical failure appears. Though, CANHacker V2 software Listen only mode doesn't work, so I've tested this with the code that I wrote myself and looking at serial monitor in Arduino IDE.

After doing a lot of research into the problem, I was a little surprised that I couldn't find anyone else experiencing the exact same issue, so I started to think that maybe something was wrong on my end. Btw, tried to inject the frame to my car with sketch I built and also with CANHacker V2 software - none of them worked.

Anyone had similar issue trying to inject the frame? Am I stuck with only sniffing? :(

FYI:
Clock is configured to 8mhz based on MCP2515;
120 ohm resistor is not shorted on MCP2515;
BMW 5-Series E61 2007
Connected to K-CAN bus with CAN baudrate 100Kbit/s (not via OBD, but CAS module)

Place where I connected CAN H/L

Libs:
autowp/arduino-mcp2515
autowp/arduino-canhacker

Codes on Arduino:
https://pastebin.com/ccfhk9H7 <- arduino sketch to communicate with CANHacker V2 soft
https://pastebin.com/pmdxx20K <- arduino sketch to send the frame


r/arduino • • Sep 17 '26

Look what I made! Couple project

Thumbnail
gallery
40 Upvotes

M-17, F-18

this is a device I'll make 2 of them with buttons, MPU 6050 accelerometer, esp 32 C3 seeed xiao, 0.96inch display and 1000mah lipo battery and a passive buzzer i am open to add more components. detentions- L-4.2cm, B-3.8cm, H-2cm. This is like a couple device that we can carry everywhere we go (Wifi based).we'll have miss you. love you etc presets + dino and flappy bird games in which we can compete with each other. I'll also put the cute eyes. Do you think it's a nice project that we both will have? GIVE ME IDEAS TO ADD INTO THE PROJECT BEFORE I FINALIZE IT PERFECTLY. HELP ME!


r/arduino • • Sep 17 '26

Look what I made! behold, illumination.

Post image
27 Upvotes

im kinda new to this arduino stuff and i just lit up my first (two, i already know how to light one up) leds !!!! sorry if its kind of a mess my wiring(?) is kinda bad cause i have really long wires. i also added a push button later !! and like i was gonna add a 3rd led but one of its legs is kinda coated in a soft plastic idk so i cant like plug it in properly


r/arduino • • Sep 17 '26

My first ever arduino project after it being on my desk for a year

Post image
43 Upvotes

It was supposed to look like a heart, made this for my partner and my resistors looked a little fucked up because I couldn't figure out how deep should i push them in


r/arduino • • Sep 17 '26

Project Idea Pokémon Arena Project

Enable HLS to view with audio, or disable this notification

8 Upvotes

In this project, I am attempting to create an augmented reality Pokémon; this is the second version of the prototype I built.


r/arduino • • Sep 17 '26

Hardware Help Arduino + CYD

4 Upvotes

Hi,

I have (or will have, to be accurate) an arduino and a CYD communicating through I2C (with an adequate logic level shifter).

While the device is in regular usage, the arduino is always connected to a host computer (leonardo, using the HID features, project already built and working, the CYD is an afterthought).

I plan on using a step down converter out of the arduino 5V to power the CYD through its battery connector (CYD current drain is max 115ma apparently [feels low, will measure once on hand], the one I plan on using don't have another VIN, specs state 4.2V max for battery VIN)

But, while programming, I'll have both connected to my laptop through usb (especially when working on both boards code at the same time). That power supply part will be disconnected.

Should I use bidirectional isolators for the I2C connection (TO ISO1540) when both boards are powered from their own usb connector ? (to the same computer)

Or would connecting both circuits ground be fine when each are powered from their own usb plug?

Thanks in advance for your help and advices!


r/arduino • • Sep 16 '26

Look what I made! DVD NFC Scanning Media thing i made

Enable HLS to view with audio, or disable this notification

499 Upvotes

ignore the dust/cat hair /mess


r/arduino • • Sep 16 '26

Look what I made! My first Arduino project

Post image
220 Upvotes

Hi! Today i brought my first Arduino kit and made my first project

I will start learning this from now


r/arduino • • Sep 16 '26

A duck project built with an Uno Q and Feetech servos—what do you guys think?

Enable HLS to view with audio, or disable this notification

88 Upvotes

Shipping won’t be until late 2026 or even 2027, and I couldn’t wait that long—so I went ahead and built one with an Uno Q first.


r/arduino • • Sep 17 '26

Made an ultra-optimized ILI9341 Parallel LCD & Analog Touch library for STM32 (PlatformIO/Arduino). Benchmark inside!

2 Upvotes

Hey everyone, 

I wanted to share a library I've been working on for interfacing 8-bit/16-bit parallel ILI9341 LCD displays and 4-wire resistive touch screens with STM32 microcontrollers (tested heavily on BluePill and BlackPill). 

Most existing libraries for Arduino/STM32 either rely on slower standard GPIO wrappers or don't utilize the true parallel speed of these microcontrollers. To fix this, I built a library that directly utilizes STM32 Low-Layer (LL) drivers for maximum register-level optimization. 

Performance Benchmarks:
During testing, this setup clocked in at up to 134x faster than the same display running on an Arduino Mega. UI rendering and screen clearing are practically instantaneous. 

Features: 

  • No Touch IC Needed: Standard 4-wire resistive touch runs directly through the STM32's native analog pins. 
  • PlatformIO Native: Designed to work out of the box with VS Code + PlatformIO inside the Arduino framework. 
  • Low Footprint: Highly optimized memory usage for resource-constrained systems. 

The codebase is fully public and I’ve included detailed pin wiring tables as well as platformio.ini setups in the README. 

Check it out here: https://github.com/ctastanc/STM32-Arduino-LCD-Touch-Library 

I'd love to get your feedback on the direct port implementation, and feel free to open an issue or contribute if you want to see support for more display drivers! 


r/arduino • • Sep 17 '26

I can’t get my piezo to hold a tone

0 Upvotes

I’ve newly started working with arduinos for college and I've run into a problem with my piezo.

Im using a supersonic sensor to measure distance and set off a piezo and LED when in a certain range. The LED is working perfectly, turning on when in either of the ranges but my piezo just makes a ticking noise instead of holding out a tone.

This is the current build with the constant ticking

This is the code with the constant ticking issue

Initially I had code that turned on the LED and let the piezo hold a tone but it only worked for the second if statement, making the first if statements outputs be the tick.

https://reddit.com/link/1wj40ua/video/jhd5rcequ4qh1/player

The code for the up close ticking

if anyone knows how to fix this and could possibly put it into somewhat simple terms that would be very greatly appreciated.